Network Electronics V0106Q User manual

network-electronics.com
Analogue Video Distributor
-1x6 Quad
Rev. 5
Flashlink User Manual
V0106Q

V0106Q Rev. 5
2
Network Electronics ASA
Thorøya
P.O. Box 1020
Sandefjord, Norway
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.network-electronics.com
Service Phone: [phone]
Revision history
Current revision of this document is the uppermost in the table below.
Revision Replaces Date Change description
5 4 2007-10-29 New front page and removed old logo.
4 3 2007-03-30
Added Materials Declaration and EFUP; updated
EC Declaration of Conformity.
3 2 09/02/05
Updated Frequency response specification to
500MHz.
2 1 23/11/04
Removed reference to discontinued product
V0106D.
1 0 30/03/04
Updated warranty description, and combined D
and Q.
0 - 10/10/00 Initial Revision.

V0106Q Rev. 5
3
Contents
Revision history............................................................................... 2
1 Product overview......................................................................... 4
2 Specifications .............................................................................. 5
2.1 Technical specifications ...............................................................................5
2.2 Rear view.....................................................................................................5
2.3 Power connection........................................................................................5
3 Connections ................................................................................ 7
3.1 Termination of video signals ........................................................................7
General environmental requirements for Network Electronics
equipment ..................................................................................... 8
Product Warranty ........................................................................... 9
Materials Declaration and EFUP .................................................... 10
Materials declaration .......................................................................................10
Environmentally Friendly Use Period (EFUP).....................................................10
Recycling information......................................................................................11
EC Declaration of Conformity ....................................................... 12

V0106Q Rev. 5
4
1Product overview
The V0106Q video distribution amplifier provides four separate 1 to 6 video
distribution amplifiers in a single rack space ultra low profile enclosure.
Looped inputs allow forming of different configurations. A high frequency
(500MHz) and high performance video amplifier circuit in SMD technology
with minimum signal degradation makes the V0106Q suitable for use with
graphic workstations, black-burst distribution, house reference feeds and other
demanding studio, CCTV, multimedia, industry and broadcast applications.

V0106Q Rev. 5
5
2Specifications
2.1 Technical specifications
Frequency response: 0 – 500MHz –3dB
Differential gain: < 0.07%
Differential phase: < 0.22°
Video S/N Ratio: > 70dB
Gain: 0dB ±0.1dB
Number of inputs: 4, looped
Number of outputs: 4x6
Impedance: 75Ohms
Return loss: > 40dB
Max signal: 2 Vp-p
Coupling: DC
Connector: BNC
AC power: External power supply 100 – 260 VAC
DC power: ±5V, connector DB9 male
Dimensions: 483 x 44 x 40 mm (19”, 1RU)
2.2 Rear view
Video inputs A/B Video inputs C/D
Power connector Video outputs A/B Video outputs C/D
2.3 Power connection
Do not connect mains to the desktop power supply before connecting
the power supply to the distributor.
Connect the DB9 female connector from the desktop power supply to the
main unit. Tighten the screws to assure a proper contact. To connect mains to
the desktop power supply you need a mains cord with IEC 320 connector.
V0106Q is normally delivered with the desktop power model AC ±5V / 10W.
Upon customer request, V0106Q can also be delivered with DC ±5V / 30W,
which may be fed by a 36 - 72 VDC mains power source. A Frame mounted
power supply solution is also available.
Please refer to the latest Network Product Catalogue for power supply types,
or call the Network Electronics ASA for this information.

V0106Q Rev. 5
6
V0106Q requires ±5V DC with a minimum current of 300mA. The following
pin-out is used on the DB9 male power connector:
Pin #1 0V
Pin #2 +5V
Pin #6 -5V

V0106Q Rev. 5
7
3Connections
3.1 Termination of video signals
It is not necessary to terminate unused video outputs.
The looped outputs on the input section of the V0106Q must always be
terminated. A 75 ohms termination plug is used direct on the V0106Q.
To assure correct frequency response a precision termination plug with 0,1%
tolerance must be used.
If the video signal is routed from the looped outputs to other devices, the end
of the loop chain must have an internally terminated device or a termination
plug.

V0106Q Rev. 5
8
General environmental requirements for Network Electronics
equipment
1. The equipment will meet the guaranteed performance specification under the
following environmental conditions:
- Operating room temperature range: 0°C to 45°C
- Operating relative humidity range: < 95% (non-condensing)
2. The equipment will operate without damage under the following environmental
conditions:
- Temperature range: -10°C to 55°C
- Relative humidity range: < 95% (non-condensing)

V0106Q Rev. 5
9
Product Warranty
The warranty terms and conditions for the V0106Q follow the General Sales
Conditions by Network Electronics ASA. These conditions are available on the
company web site of Network Electronics ASA:
www.network-electronics.com

V0106Q Rev. 5
10
Materials Declaration and EFUP
Materials declaration
For product sold into China after 1st March 2007, we comply with the
“Administrative Measure on the Control of Pollution by Electronic Information
Products”. In the first stage of this legislation, content of six hazardous
materials has to be declared. The table below shows the required
information.
Toxic or hazardous substances and elements
組成名稱
Part Name
鉛
Lead
(Pb)
汞
Mercury
(Hg)
镉
Cadmium
(Cd)
六价铬
Hexavalent
Chromium
(Cr(VI))
多溴联苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
V0106Q X O O O O O
DP AC ±5V, 10W O O O O O O
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this
part is below the limit requirement in SJ/T11363-2006.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials
used for this part is above the limit requirement in SJ/T11363-2006.
Environmentally Friendly Use Period (EFUP)
EFUP is the time the product can be used in normal service life without leaking
the hazardous materials. We expect the normal use environment to be in an
equipment room at controlled temperature range (0ºC - 40ºC) with moderate
humidity (<90%, non-condensing) and clean air, not subject to vibration or
shock.
Where a product contains potentially hazardous materials, this is indicated on
the product by the appropriate symbol containing the EFUP. The hazardous
material content is limited to lead (Pb) in some solders. This is extremely
stable in normal use and the EFUP is taken as 50 years, by comparison with
the EFUP given for Digital Exchange/Switching Platform in equipment in
Appendix A of “General Rule of Environment-Friendly Use Period of Electronic
Information Products”. This is indicated by the product marking:
50
It is assumed that while the product is in normal use, any batteries associated
with real-time clocks or battery-backed RAM will be replaced at the regular
intervals.
The EFUP relates only to the environmental impact of the product in normal
use, it does not imply that the product will continue to be supported for 50
years.

V0106Q Rev. 5
11
Recycling information
Network Electronics ASA provides assistance to customers and recyclers
through our web site http://www.network-electronics.com. Please contact
Network Electronics ASA’s Customer Support for assistance with recycling if
this site does not show the information you require.
Where it is not possible to return the product to Network Electronics ASA or its
agents for recycling, the following general information may be of assistance:
-Before attempting disassembly, ensure the product is completely
disconnected from power and signal connections.
-All major parts are marked or labelled to show their material content.
-Depending on the date of manufacture, this product may contain lead
in solder.
-Some circuit boards may contain battery-backed memory devices.

EC Declaration of Conformity
MANUFACTURER Network Electronics ASA
P.B. 1020, N-3204 SANDEFJORD, Norway
AUTHORISED REPRESENTATIVE
(Established within the EEA) Not applicable
MODEL NUMBER(S) V0106Q
DESCRIPTION Analogue Video Equaliser Distributor – 1x6 QUAD
DIRECTIVES this equipment complies with LVD 73/23/EEC
EMC 89/336/EEC
HARMONISED STANDARDS applied in order to
verify compliance with Directive(s)
EN 55103-1:1996
EN 55103-2:1996
EN 60950-1:2006
TEST REPORTS ISSUED BY Notified/Competent Body Report no:
Nemko 199922157016
TECHNICAL CONSTRUCTION FILE NO Not applicable
YEAR WHICH THE CE-MARK WAS AFFIXED 1999
TEST AUTHORIZED SIGNATORY
MANUFACTURER AUTHORISED REPRESENTATIVE
(Established within EEA) Date of Issue
2007-03-30
Place of Issue
Not applicable Sandefjord,
Norway
Name Nils B. Sannes
Position Quality Manager
(authorised signature)