New England Burbank Raised Potting Bench User manual

General Information
•Read Instructions through carefully before beginning assembly.
•When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
•We recommend an area approx 4’x 8’ (1.2 m x 2.4 m) for unobstructed assembling.
•You should not need to use excessive force when assembling components.
Burbank Raised Potting Bench
AS SEMBLY IN ST RUCTIONS
1
Not to Scale
1
4
Ver 2.2/072617
www.newenglandarbors.com
www.newenglandarbors.co.uk
Please read through before starting assembly.
Check Box for These Contents
In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
(UK Tel: [phone] (Mon. to Fri. 1:00 PM to 10:00 PM GMT).
11
8
15
6
2
9
7
12
5
3
10
13
16 17
65 in
(165 cm)
32 1/2 in
(83 cm)
37 in
(94 cm)
44 in
(112 cm)
20 in
(51 cm)
24 in
(61 cm)
6 in
(15 cm)
18 1/2 in (47 cm)
14
1. Post Caps (2) - 10611
2. Trellis Top Rail (1) - 10971
3. Trellis Post - Left (1) - 10972
4. Trellis Post - Right (1) - 10973
5. Trellis Slats - Vertical (5) - 10974
6. Trellis Horizontal Rail - Middle (3) - 10975
7. Trellis Horizontal Rail - Bottom (1) - 10976
8. Potting Bench Pre-assembled Left Panel (1) - 10226
9. Potting Bench Boards (4) - 10978
10. Potting Bench Pre-assembled Top Rail - (2) - 10979
11. Potting Bench Board Supports (2) - 10980
12. Potting Bench Pre-assembled Shelves (2) 10981
13. Potting Bench Pre-assembled Right Panel (1) - 10219
14. Corner Brackets (4) - 10227
15. 1 1/2” (38 mm) Stainless Steel Screws (16) - 20005
16. 5/8” (16 mm) Stainless Steel Screws (20) - 20016
17. S-Hooks (3) - 10990

The Burbank Potting Bench
3
2
2
STE P ONE
Lay one of the pre-assembled side panel on the ground as shown
aside (Left panel shown) and insert the two pre-assembled top rails
as well as the two pre-assembled shelves. You might need a helper
to stabilize the components as they are inserted into the side panel.
Note: The shelf rails havetabs at the end of the extrusions; push them
firmly intothe routed hole until the tabs lock into place.
With a helper, align and insert the other pre-assembled side panel
onto the assembly from Step One above.
Push shelf rails until the tabs lock into place.
Carefully stand upthe potting bench on its legs as shown and insert
the two board supports tohelp stabilize the entire assembly.
Make sure the two board supports are fully inserted into the pre-
assembled top rails (they are notched)
1
The Burbank Potting Bench
www.newenglandarbors.com
1
Note: Shelf braces should be facing
down (away from the top rails)
2
3

The Burbank Potting Bench
3
5
STEP ONE
Fasten the Pre-assembledside panels to the top rails using two
1-1/2” (38 mm) screwsprovided as shown. Repeat for all four corners.
Line up and insert the four potting bench boards one by one.
Note the difference between the four boards and the order
they go in (see illustration below).
4
The Burbank PottingBench
4
5
Fasten corner brackets to the underside of the top rails to the
posts as shown using four short screws per bracket.
6
6

The Burbank Potting Bench
3
4
2
STEP T WO
To assemble thelattice, first insertthe vertical trellis slats (5)into
the threemiddle rails as shown aside. Excessive force should not be
needed.
Insert the component from the previous step onto the top and
bottom rail asshown.
Note the routed hole offset on the bottom rail. Make sure the
holes are closer towards the back (flat part ofthe top rail).
Insert the left and right trellis posts asshown.
Note the tabs at the end of the rails. Once inserted, the tabs
will lock the assembly into place.
1
The Burbank Potting Bench
1
2
3

The Burbank Potting Bench
5
STEP TWO
Fasten the top rail onto the trellis posts by fastening two 5/8” (16 mm) screws
per side as shown. Screws do not need to be fasten all the way down (half
way is sufficient, to prevent the top rail from pulling out of the trellis posts)
Attach the trellis assembly onto the back posts of the potting
bench followed by the two posts caps as shown. You may need
a helper to align the two posts together.
Fasten the trellis assemblyto the potting bench using 8 of the
1 1/2” (38 mm) screws provided as shown.
Hang the three provided hooks on the trellis as shown to hang
gloves, pots, garden tools, etc.
4
4
5
6
6
7
North America Toll Free Phone: [phone]
United Kingdom Tel: [phone]
www.newenglandarbors.com
www.newenglandarbors.co.uk
5
7