New England PX947 User manual

Dimensions
Width - 70cm
Depth - 38cm
Height - 45cm
Important– Please read these instructions fully before starting assembly
Assembly Instructions- please keep for future reference
464/3944
Ottoman
Issue 1 - 12/04/2017
XK092
PX947

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
•Assemble the item as close
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Handy Hints
• We do not
recommend the use
of power drill/drivers
for inserting screws,
as this could damage
the using. Only use hand
screwdrivers

A×1
B×1
C×1
D×1 E×1
F×1
Components - Fittings
Note:
may be supplied than are required.
1 ×12 2 ×2 3 ×8 4 ×8 5 ×8 6 ×4 7 ×1
2
Components -Panels
Please check you have all the panels listed below
Tools required
Phillips screwdriver
(medium & large)
1 2 3 4 5 6 7
A
A
A
A
A
B
A
A
C
A
A
DA
A
E
A
A
F

3

4
Assembly Instructions
Step 1
Step 3
Step 2
Inserting Male Camlocks
1. Insert 4 x Male
Camlocks 4 into Left
Side Panel D and 4 x
Male Camlocks 4 into
Right Side Panel E as
shown
4
Inserting Dowels
1. Into Back Panel C
and Front Panel B
insert 8 x Dowels 1 as
shown
4
4
4
4
44
4
3
3
A
A
D
A
A
E
4
4
4
4
4
4
4
4
A
A
D4
A
A
E
5 5
55
5
5
5
5
A
A
C
A
A
B
A
A
C
A
A
B
5
A
A
D
A
A
C
3
3
1. Locate Back Panel C
onto Male Camlocks in Left
Side Panel D as shown
2. Into holes shown in
Back Panel C insert 2 x
Female Camlocks 3 as
shown.
A
A
C
A
A
D
A
A
C
3

5
Assembly Instructions
Step 4
Step 5
3
3
3
3
1. Locate Front Panel C
onto Male Camlocks in Left
Side Panel D as shown
2. Into holes shown in
Front Panel C insert 2 x
Female Camlocks 3 as
shown.
A
A
B
A
A
D
A
A
B
3
A
A
B
3
A
A
F
1. Slide Base Panel f
into position
A
A
F
Step 6
A
A
E
33
3
3
1. Locate Male Camlocks
in Right Side Panel E
into adjacent holes in Front
and Back Panels B and
C
2. Into holes shown in
Front Panel and Back
Panels B and C insert
4 x Female Camlocks 3
as shown.
A
A
E
A
A
B
A
A
C
A
A
BA
A
C
3
3

Assembly Instructions
Step 7
6
2
7
7
A
A
A
A
A
C
2
1x3
1x3
2
2
7 7
6
6
6
6
1x3
1x3
6
6
6
6
1. Connect 2 x Hinges 2
to Back Panel C using
3 x Screw 1 per hinge
2. Connect Lid Panel A
to the Hinges as shown
using 3 x Screw 1 per
hinge
3. Connect Safety Stay 7
to the unit using 4 x
Screw 6
Please note: The safety
stay must be mounted
correctly. Failure to do so
may cause damage to the
unit.
Assembly Complete
2
A
A
C
1
A
A
A
1
7
6