Newtech Milazzo User manual

Milazzo Installation
& Fixing Guide
www.newtech.co.nz | 0800 728 662
MODULAR BATHROOM SYSTEM

Milazzo Modular Bathroom System INSTALLATION & FIXING GUIDE
02
FIXING SHELF AND SLAB TOP BRACKETS
Milazzo shelf and timber slab top brackets are to be fixed to a double stud at the
pre-line stage of the build.
Shelf and timber slab top brackets are to be screwed to the wall with 10g x 1 ⁄”
screws and screwed to the shelf/slab top with 10g x 1 1/4 “screws.
Milazzo shelf and timber slab top brackets
are to be used on spans larger than
500mm spaced at a max of every 500mm.
Important: Maximum timber slab top overhang without support is 300mm.
10g x 1 ⁄” screws
10g x1 ⁄” screws
Wall fixing
10g x 1 ⁄”
screw
10g x 1 ⁄” shelf
joining screws
Wall fixing
10g x 1 ⁄”
screw
10g x1 ⁄”
screws
10g x1 ⁄” shelf
joining screws
Wall fixing
10g x 1 ⁄”
screw
10g x 1 ⁄” shelf
joining screws
FIXING SHELF AND SLAB TOP TO THE WALL
Milazzo shelf and timber slab top brackets
are to be used on spans larger than
500mm spaced at a max of every 500mm.

Milazzo Modular Bathroom System INSTALLATION & FIXING GUIDE
03
Timber slab top is to be fixed to cabinetry with front and back brackets.
Important: Maximum StoneCast and Quartz slab top overhang without support is 300mm.
28
30
1,2
50
80
40
1,2
80 80
40
Milazzo timber slab top
front bracket
Milazzo timber slab top
back bracket
Milazzo timber slab top with
Luma Lite front bracket
Milazzo timber slab top with
Luma Lite back bracket
Milazzo timber
slab top front
bracket
Milazzo timber
slab top back
bracket
INSTALLING LUMA-LITE
Luma lite to be fixed in place with
silicone every 300mm to cabinet and basin.
FIXING SLAB TOPS TO CABINETRY
Luma lite to be fixed in place
with silicone every 300 mm
to cabinet and basin.
FIXING SLAB TOPS TO CABINETRY WITH SILICONE
Quartz and StoneCast slab tops are to be fixed to cabinetry with silicone approximately
every 300mm.
Luma Lite LED Driver to
be mounted to the internal
rear of the cabinet.

Milazzo Modular Bathroom System INSTALLATION & FIXING GUIDE
04
Cabinets are to be screwed together with 10g x 1 ⁄” screws.
When fixing 2 cabinets with drawers in,
the drawers may need to be removed to
allow for easy screwing.
Wall fixing 10g x 1 ⁄”
screws. 50mm from
top edge
Wall fixing 10g x 1 ⁄”
screws
10g x1 ⁄” cabinet
joining screws
FIXING CABINETRY TOGETHER
CONNECTING TOE KICK PLINTH TO CABINETRY
Toe kick plinth is to be connected to cabinetry with concealed angle brackets.
730
475
120
119
115
880 1180
1470 1770

Milazzo Modular Bathroom System INSTALLATION & FIXING GUIDE
05
• Cabinet configuration may aect plumbing options and layout for your basins.
• Some basin locations may not be possible with some cabinet configurations.
• Please consult with Newtech and your plumber to ensure your plumbing configuration is correct for
your cabinetry configuration.
NOTE
Newtech
Phone: [phone]
[e-mail]
www.newtech.co.nz
For warranty information, please visit our website.
CONTACT AND WARRANTY INFORMATION
MILAZZO TAP HOLE CONFIGURATION
CORAL RIDGE ROUND QUARTO ROUND 410 MAYA ROUND
CORAL DIAMOND ROUND TONI RECTANGULAR MAYA SQUARE
CORAL RIDGE SQUARE TONI OVAL WASHINGTON
HARPER
200
70
185
185 40
175
80
200
85
250
210
70
185
40
180
175
175
70
175
275
70
180
85
270
260
DRAWER REMOVAL & LEVELING CABINETRY
REMOVING DRAWER INSERTING DRAWERS
Open the drawer fully. Place your hands centrally on the top and bottom of the
draw front. With a swift motion, pull the drawer directly upwards. This will pop the
drawer out of it’s runners.
Place the drawer back onto the runners. Place one hand towards the back of the
draw-er and apply a small amount of weight downwards. With the other hand squeeze
the grey tab on both the left and right side towards the drawer front until you hear a
‘click’. To ensure correct installation check that the rear of the drawer does not lift
upwards.
LEVEL THE VANITY
Note: Floor standing vanities should likewise, be checked for sitting level, plumb and
square and suitably packed to achieve this. Fix to the wall to secure through mounting
brackets on the back rail.
Open the drawer fully. Place your hands centrally
on the top and bottom of the draw front. With a
swift motion, pull the drawer directly upwards.
This will pop the drawer out of it’s runners.
Place the drawer back onto the runners. Place one
hand towards the back of the drawer and apply a
small amount of weight downwards. With the other
hand squeeze the grey tab on both the left and
right side towards the drawer front until you hear a
“click”. To ensure correct installation check that the
rear of the drawer does not lift upwards.
LEVEL THE VANITY
Note: Floor standing vanities should likewise, be
checked for sitting level, plumb and square and
suitably packed to achieve this. Fix to the wall to
secure through mounting brackets on the back rail.
TONI ROUND
210
70
185
175
70
175
175
70
175