NewTechWood Planter Box User manual

Planter Box Installation Guide
v20191125

Planter Box Installation Guide / v20191125 1
Important Note 2
Planter Box Component for 1x3 3
Single Layer Installation 4
Multi-layer Installation 5
CONTENTS

Planter Box Installation Guide / v20191125 2
IMPORTANT:
Read All Sections Before You Start
For the most up to date information, please visit our website @ www.newtechwood.com
Prior to installing any composite product, it is recommended that you check with local building codes
for any special requirements or restrictions. The diagrams and instructions outlined in this guide are
for illustration purposes only and are not meant or implied to replace a licensed professional. Any
construction or use of NewTechWood must be in accordance with all local zoning and/or building codes.
The consumer assumes all risks and liability associated with the construction and use of this product.
Safety
When dealing with any type of construction project, it is necessary to wear appropriate safety equipment
to avoid any risk of injuries. NewTechWood recommends but is not limited to the following safety
equipment when handling, cutting, and installing the product: gloves, a respiratory protection, long
sleeves, pants, and safety glasses.
Tools
Standard woodworking tools may be used. It is recommended that all blades have a carbide tip.
Environment
A clean, smooth, flat, and strong surface is needed to install the UltraShield Naturale Planter Box
correctly. Please check with local building codes before ever installing any type of decking. If installation
does not occur immediately, NewTechWood's products need to be put on a flat surface at all times.
Never ever should it be put on a surface that is NOT at.
Static
Static can also be more prevalent in areas that are of higher altitude because the humidity is lower. For
these areas, be careful of using conducive objects such as metal railing and chairs as static shocks might
occur more often. A potential way to lower the amount of static shocks occurring is to apply Staticide
(www.aclstaticide.com) on your deck or use anti-static mats before doorways. NewTechWood’s products
have been tested against EN 1815 - Assessment of Static Electrical Propensity and have received values
under the maximum standard of 2kV.
Layout
Before installing the UltraShield Naturale Planter Box, always make sure that you are installing it on a
clean smooth at surface.
The UltraShield Naturale Planter Box CANNOT be installed on places such as dirt, soil, or raised structure.
It must be laid out on a at solid surface.

Planter Box Installation Guide / v20191125 3
Planter Box Components for 1x3
C
B
G
E
F
D
A
A - UQ0116
(X4)
D - UQ0119
(X1)
E - UQ0120
(X8)
C - UH08-252
(X2)
B - UH08-988
(X2)
F - UQ0115
(X4)
G - UQ0101
(X3)
IMPORTANT POINTS:
•Parts B, C, D will be different depending on the planter box kit model.
•Parts D, G quantity will be different depending on the planter box kit model.

Planter Box Installation Guide / v20191125 4
1Lay & connect the grids (G-UQ0101) on a at
surface as shown in Diagram 1.
DIAGRAM 1
DIAGRAM 3
2Insert the posts (F-UQ0115) on the 4
corners as shown in Diagram 2.
Note: The groove side of the post should
be facing inward for inserting the boards.
Lay the perforated (D-UQ0119) sheet on the
grids as shown in Diagram 3.
3
Insert 2 plugs (E-UQ0120) into the pre-
drilled holes in every board to lock the
board and post together as shown in
Diagram 6.
5
Press down to x the post caps (A-UQ0116)
as shown in Diagram 7 and 8.
6
DIAGRAM 2
Insert the boards (B-UH08-988, C-UH08-
252) between the posts as shown in
Diagram 4 and 5.
4
Single Layer Installation
The following installation is for the 1x3 planter box. Other planter boxes will be installed in the same
manner, the only difference being the length of the boards.
DIAGRAM 6
DIAGRAM 4
DIAGRAM 5
DIAGRAM 7
DIAGRAM 8

Planter Box Installation Guide / v20191125 5
1Follow the steps 1-5 in Single Layer
Installation on page 2.
Insert the boards between the posts as
shown in Diagram 10 and 11.
3
Insert 2 plugs into the pre-drilled holes
in every board to lock the board and post
together as shown in Diagram 12.
4
Press down to x the post caps as shown
in Diagram 13 and 14.
5
DIAGRAM 9
DIAGRAM 10
DIAGRAM 12
DIAGRAM 13
DIAGRAM 14
DIAGRAM 11
Multi-layer Installation
The planter box can be stacked up and installed up to 3 layers.
2Insert the posts on top of the 4 installed
posts as shown in Diagram 9.
Note: The groove side of the post should
be facing inward for inserting the boards.

Planter Box Installation Guide
v20191125
©2019 Huidong Meixin Plastic Lumber Products Manufacturing Co., Ltd.
NewTechWood is a registered trademark of Huidong Meixin Plastic Lumber Products
Manufacturing Co., Ltd. To obtain a copy of the most current version of this installation guide,
visit us online at www.newtechwood.com.
®