Nex-tech QC3862 User manual

Miniature 1080p WiFi IP Camera
QC3862
User Manual
Thank you for purchasing this product, the machine uses a unique
ultra-portable design, it can be applied in various fields, it is very
convenient, safe and bring a colorful life for you, please set your
camera correctly in accordance with the guidelines of the quick
steps .
I. Start
Switch the power to ON to boot up the camera. It will take about
30-60 seconds to finish booting up.
With the power switch ON, hold down the reset button for 5
seconds to restore the factory settings.
1. The blue light is the power indicator. Solid blue means the
device is on.
2. The red light is the WiFi indicator.
a. Point-to-point mode (direct connection between phone
and camera): red light flashes slowly.
b. Remote access mode (camera connected to a WiFi
router): solid red light.

c. Failure to connect when in remote access mode: red light
flashes quickly.
Note: resetting the camera would make it into point-to-
point mode.
to enable or
to enable or
3. Infrared night mode control: On the app, tap
disable night mode.
4. Indicator lights control: On the app, tap
disable the indicator lights.
II. APP software download
For Android phones, search for APP software named “MiniCam ” in
Google Play.

For Iphone, APP software named “MiniCam” in App Store.
III. Point-to-point mode
Enter the phone settings where WIFI signal inside, find the signal
(If the UID number WiFi signal is not available, please try to reset
the camera) and connected as the picture shows

IV. Connect camera to WiFi router
Method 1: Add a new device to connect the camera online point-
to-point, click into the camera system will prompt whether to
connect WIFI, rapid network configuration method as shown in
the following figure
Then turn on the phone APP (minicam) and the new device will pop up
automatically as shown in Figure 2 above. After clicking "OK", the following
picture is shown.
Click into the online camera to see the video as shown above.

Method 2: In the case of point-to-point connection of the camera online, enter
the list of cameras as shown in the following figure
Click on the icon to enter "Wi-Fi Config" and select your WIFI. Enter the
password to configure the camera to connect to WIFI as shown below.

After clicking "confirm", the camera will automatically restart (about 30
seconds, when the camera shows "online", so that remote access can be
made.
Memory Card Video Settings: Click on the icon to enter "Micro SD
Config", which can set the mode of memory card video and screen size, as
follows:
Alarm Settings: Click on the icon to enter the "Advanced Configuration" and
then to "Alarm Configuration", you can turn on or off the mobile detection alarm,
as shown below.
The menu can be popped up by clicking on the screen when the camera is
watching on the mobile phone. The main menu options are shown in the figure
below.

Icons and buttons for video pages

7. Specifications
Resolution Ratio 1080P/720P/640P/320P
Video Format AVI
Frame Number 25
Visual Angle 150 degree
Motion Detection Camera
Shooting
Straight line 6 meters
Minimal Illumination 1LUX
Video Duration Over 1 Hours
Compressed Format H.264
Recording Range 5㎡
Consumption 240MA/3.7V
Storage Temperature -20-80 degree centigrade
Operating Temperature -10-60 degree centigrade
Operation Humidity 15-85%RH
Memory Card Type TF card
Player Software VLCPlayer/SMPlayer
Computer Operating Windows/Mac OS X
System
Mobile Phone Operating
System
Android/iOS
Web browser IE7 and above,chrome,firefox safari.etc
Largest customer 4

8.FAQ
1. Why remote monitoring is not smooth?
You should choose suitable resolution to watch according to your Internet.
2. Why SD card cannot save?
SD card must be formatted if this is your first time to use.
3. Why Connection is not on the network?
Select the correct connection way according to your network
4. Why APP remote viewing SD card video is not smooth?
As a result of the mobile decoding ability are different, and you can adjust
video equipment according to your mobile’s resolution
5. How to find my password?
To press reset key with 10 seconds and Restore the factory Settings.
Note:
The device name easy to remember just write
Paste on P2P UID
Password had not been changed, then that is 8888 if you have
modified, please fill in the date.
Special note:
1. If the camera is not connected to the router, please reset,
even after a hot machine to configure.
2. If the camera does not read the memory card, or mobile
phone in the LAN advanced settings in the background
formatting after use.
2. Shutdown Reset: Please re-operation off and reset when you
see the red light.

Distributed by:
TechBrands by Electus Distribution Pty. Ltd.
320 Victoria Rd, Rydalmere
NSW 2116 Australia
Ph: 1300 738 555
Int’l: [phone]
Fax: [phone]
www.techbrands.com
Made in China