Nexa LCMR-1000 User manual
OTHER INFORMATION
Indoor range: up to 30 m (optimal conditions). The range is strongly
dependent on local conditions, such as the presence of metals. For
example, the thin metal coating in Low-emissivity (Low-E) glass has
a negative impact on the range of radio signals.
There may be restrictions on the use of this device outside the EU. If
applicable, check whether this device complies with local directives.
Maximum load: Never connect lights or equipment that exceed
the maximum load of the receiver, as it can result in defects, a short
circuit or fire.
Life-support: Never use Nexa products for life-support systems or
other applications in which equipment malfunctions can have life-
threatening consequences.
Interference: All wireless devices may be subject to interference,
which could affect performance. The minimum distance between 2
receivers should be at least 50 cm.
NNL
NEXA
Learn button LED indicator
Neutral
Neutral In
Live In Live Out
WIRING DIAGRAM
LCMR-1000
RELAY, 1 CHANNEL
TECHNICAL DATA
A declaration of conformity is available at www.nexa.se
LCMR-1000
Power source 220-240 V~50 Hz
Max. charge 2300 W / 10A
Frequency System Nexa (433.92 MHz)
Range up to 30 m
Storage locations 6
Power consumption < 1 W (standby)
Operating temperature 0-40 °C
IP rating IP20 Indoor use
Dimensions 53 x 53 x 25 mm
Built-in receiver for wireless control of lamps, etc. The receiver
needs both phase and neutral. The receiver is fully compatible with
other System Nexa products.
SAFETY
Read through the entire instruction first. Engage a professional if so
required. Nexa cannot be held liable if the product is used for any
purpose other than the one for which it is designed, or if there is
failure to comply with the instruction.
Never connect bulbs or equipment exceeding the receiver’s
maximum stated load – this may lead to faults, short-circuiting or
fire. Do not attempt to repair the product.
The product contains no repairable parts.
INSTALLATION
Make sure that the conductors are powered down by turning off
the power in the distribution box.
Connect LCMR-1000 as shown in the wiring diagram.
LINKING
To control LCMR-1000 using a System Nexa remote control (or
other device), the transmitter and receiver must be linked as follows:
1. Power up LCMR-1000
2. Press the learn button, the LED indicator starts to flash slowly
3. Press the “ON” button for the selected channel on a System
Nexa remote control within 18 seconds
See the instructions for use for the product in question if you wish
to train other System Nexa devices (motion detector, magnetic
contact, bridge, etc.)
LINKING CONFIRMATION
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
DELETING A STORAGE LOCATION
1. Power up LCMR-1000
2. Press the learn button, the LED indicator starts to flash slowly
3. Press the “OFF” button for the selected channel to be deleted on
a System Nexa remote control within 18 seconds.
See the instructions for use for the product in question if you wish
to delete other System Nexa devices (motion detector, magnetic
contact, bridge, etc.)
DELETION CONFIRMATION
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
ENGLISH
DELETING ALL STORAGE LOCATIONS.
1. Power up LCMR-1000
2. Press and hold down the learn button for 6 seconds, the LED
indicator starts to flash quickly
3. Release the learn button and then press it again briefly.
CONFIRMATION OF DELETION OF ALL STORAGE LOCATIONS
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
STORAGE:
LCMR-1000 has 6 storage locations and can be controlled from up
to 6 different devices (remote controls, motion detectors, magnetic
contacts, bridges, etc.). If all storage locations are occupied, it is not
possible to train a new device without deleting a storage location
first: see “DELETING A STORAGE LOCATION”
CONTROL
The receiver can be controlled in a number of ways.
1. With a trained System Nexa remote control
2. With other trained System Nexa transmitters
3. With a Nexa Bridge
FUSE
LCMR-1000 is provided with a glass tube fuse, 250V/T5A, which
provides overload protection. If the fuse is broken, check the
connected device for faults or short-circuit first before replacing the
fuse and powering LCMR-1000 back up.
NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN
Repairing: Do not attempt to repair this product. There are no user-
serviceable parts inside.
Water-resistance: This product is not water-resistant. Keep it dry.
Moisture will corrode the inner electronics and can result in a short
circuit, defects and shock hazard.
Cleaning: Use a dry cloth to clean this product. Do not use harsh
chemicals, cleaning solvents, or strong detergents.
Environment: Do not expose the product to excessive heat or cold,
as it can damage or shorten the life of electronic circuit boards.
OTHER INFORMATION
Indoor range: up to 30 m (optimal conditions). The range is strongly
dependent on local conditions, such as the presence of metals. For
example, the thin metal coating in Low-emissivity (Low-E) glass has
a negative impact on the range of radio signals.
There may be restrictions on the use of this device outside the EU. If
applicable, check whether this device complies with local directives.
Maximum load: Never connect lights or equipment that exceed
the maximum load of the receiver, as it can result in defects, a short
circuit or fire.
Life-support: Never use Nexa products for life-support systems or
other applications in which equipment malfunctions can have life-
threatening consequences.
Interference: All wireless devices may be subject to interference,
which could affect performance. The minimum distance between 2
receivers should be at least 50 cm.
NNL
NEXA
Learn button LED indicator
Neutral
Neutral In
Live In Live Out
WIRING DIAGRAM
LCMR-1000
RELAY, 1 CHANNEL
TECHNICAL DATA
A declaration of conformity is available at www.nexa.se
LCMR-1000
Power source 220-240 V~50 Hz
Max. charge 2300 W / 10A
Frequency System Nexa (433.92 MHz)
Range up to 30 m
Storage locations 6
Power consumption < 1 W (standby)
Operating temperature 0-40 °C
IP rating IP20 Indoor use
Dimensions 53 x 53 x 25 mm
Built-in receiver for wireless control of lamps, etc. The receiver
needs both phase and neutral. The receiver is fully compatible with
other System Nexa products.
SAFETY
Read through the entire instruction first. Engage a professional if so
required. Nexa cannot be held liable if the product is used for any
purpose other than the one for which it is designed, or if there is
failure to comply with the instruction.
Never connect bulbs or equipment exceeding the receiver’s
maximum stated load – this may lead to faults, short-circuiting or
fire. Do not attempt to repair the product.
The product contains no repairable parts.
INSTALLATION
Make sure that the conductors are powered down by turning off
the power in the distribution box.
Connect LCMR-1000 as shown in the wiring diagram.
LINKING
To control LCMR-1000 using a System Nexa remote control (or
other device), the transmitter and receiver must be linked as follows:
1. Power up LCMR-1000
2. Press the learn button, the LED indicator starts to flash slowly
3. Press the “ON” button for the selected channel on a System
Nexa remote control within 18 seconds
See the instructions for use for the product in question if you wish
to train other System Nexa devices (motion detector, magnetic
contact, bridge, etc.)
LINKING CONFIRMATION
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
DELETING A STORAGE LOCATION
1. Power up LCMR-1000
2. Press the learn button, the LED indicator starts to flash slowly
3. Press the “OFF” button for the selected channel to be deleted on
a System Nexa remote control within 18 seconds.
See the instructions for use for the product in question if you wish
to delete other System Nexa devices (motion detector, magnetic
contact, bridge, etc.)
DELETION CONFIRMATION
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
ENGLISH
DELETING ALL STORAGE LOCATIONS.
1. Power up LCMR-1000
2. Press and hold down the learn button for 6 seconds, the LED
indicator starts to flash quickly
3. Release the learn button and then press it again briefly.
CONFIRMATION OF DELETION OF ALL STORAGE LOCATIONS
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
STORAGE:
LCMR-1000 has 6 storage locations and can be controlled from up
to 6 different devices (remote controls, motion detectors, magnetic
contacts, bridges, etc.). If all storage locations are occupied, it is not
possible to train a new device without deleting a storage location
first: see “DELETING A STORAGE LOCATION”
CONTROL
The receiver can be controlled in a number of ways.
1. With a trained System Nexa remote control
2. With other trained System Nexa transmitters
3. With a Nexa Bridge
FUSE
LCMR-1000 is provided with a glass tube fuse, 250V/T5A, which
provides overload protection. If the fuse is broken, check the
connected device for faults or short-circuit first before replacing the
fuse and powering LCMR-1000 back up.
NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN
Repairing: Do not attempt to repair this product. There are no user-
serviceable parts inside.
Water-resistance: This product is not water-resistant. Keep it dry.
Moisture will corrode the inner electronics and can result in a short
circuit, defects and shock hazard.
Cleaning: Use a dry cloth to clean this product. Do not use harsh
chemicals, cleaning solvents, or strong detergents.
Environment: Do not expose the product to excessive heat or cold,
as it can damage or shorten the life of electronic circuit boards.
OTHER INFORMATION
Indoor range: up to 30 m (optimal conditions). The range is strongly
dependent on local conditions, such as the presence of metals. For
example, the thin metal coating in Low-emissivity (Low-E) glass has
a negative impact on the range of radio signals.
There may be restrictions on the use of this device outside the EU. If
applicable, check whether this device complies with local directives.
Maximum load: Never connect lights or equipment that exceed
the maximum load of the receiver, as it can result in defects, a short
circuit or fire.
Life-support: Never use Nexa products for life-support systems or
other applications in which equipment malfunctions can have life-
threatening consequences.
Interference: All wireless devices may be subject to interference,
which could affect performance. The minimum distance between 2
receivers should be at least 50 cm.
NNL
NEXA
Learn button LED indicator
Neutral
Neutral In
Live In Live Out
WIRING DIAGRAM
LCMR-1000
RELAY, 1 CHANNEL
TECHNICAL DATA
A declaration of conformity is available at www.nexa.se
LCMR-1000
Power source 220-240 V~50 Hz
Max. charge 2300 W / 10A
Frequency System Nexa (433.92 MHz)
Range up to 30 m
Storage locations 6
Power consumption < 1 W (standby)
Operating temperature 0-40 °C
IP rating IP20 Indoor use
Dimensions 53 x 53 x 25 mm
Built-in receiver for wireless control of lamps, etc. The receiver
needs both phase and neutral. The receiver is fully compatible with
other System Nexa products.
SAFETY
Read through the entire instruction first. Engage a professional if so
required. Nexa cannot be held liable if the product is used for any
purpose other than the one for which it is designed, or if there is
failure to comply with the instruction.
Never connect bulbs or equipment exceeding the receiver’s
maximum stated load – this may lead to faults, short-circuiting or
fire. Do not attempt to repair the product.
The product contains no repairable parts.
INSTALLATION
Make sure that the conductors are powered down by turning off
the power in the distribution box.
Connect LCMR-1000 as shown in the wiring diagram.
LINKING
To control LCMR-1000 using a System Nexa remote control (or
other device), the transmitter and receiver must be linked as follows:
1. Power up LCMR-1000
2. Press the learn button, the LED indicator starts to flash slowly
3. Press the “ON” button for the selected channel on a System
Nexa remote control within 18 seconds
See the instructions for use for the product in question if you wish
to train other System Nexa devices (motion detector, magnetic
contact, bridge, etc.)
LINKING CONFIRMATION
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
DELETING A STORAGE LOCATION
1. Power up LCMR-1000
2. Press the learn button, the LED indicator starts to flash slowly
3. Press the “OFF” button for the selected channel to be deleted on
a System Nexa remote control within 18 seconds.
See the instructions for use for the product in question if you wish
to delete other System Nexa devices (motion detector, magnetic
contact, bridge, etc.)
DELETION CONFIRMATION
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
ENGLISH
DELETING ALL STORAGE LOCATIONS.
1. Power up LCMR-1000
2. Press and hold down the learn button for 6 seconds, the LED
indicator starts to flash quickly
3. Release the learn button and then press it again briefly.
CONFIRMATION OF DELETION OF ALL STORAGE LOCATIONS
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
STORAGE:
LCMR-1000 has 6 storage locations and can be controlled from up
to 6 different devices (remote controls, motion detectors, magnetic
contacts, bridges, etc.). If all storage locations are occupied, it is not
possible to train a new device without deleting a storage location
first: see “DELETING A STORAGE LOCATION”
CONTROL
The receiver can be controlled in a number of ways.
1. With a trained System Nexa remote control
2. With other trained System Nexa transmitters
3. With a Nexa Bridge
FUSE
LCMR-1000 is provided with a glass tube fuse, 250V/T5A, which
provides overload protection. If the fuse is broken, check the
connected device for faults or short-circuit first before replacing the
fuse and powering LCMR-1000 back up.
NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN
Repairing: Do not attempt to repair this product. There are no user-
serviceable parts inside.
Water-resistance: This product is not water-resistant. Keep it dry.
Moisture will corrode the inner electronics and can result in a short
circuit, defects and shock hazard.
Cleaning: Use a dry cloth to clean this product. Do not use harsh
chemicals, cleaning solvents, or strong detergents.
Environment: Do not expose the product to excessive heat or cold,
as it can damage or shorten the life of electronic circuit boards.
OTHER INFORMATION
Indoor range: up to 30 m (optimal conditions). The range is strongly
dependent on local conditions, such as the presence of metals. For
example, the thin metal coating in Low-emissivity (Low-E) glass has
a negative impact on the range of radio signals.
There may be restrictions on the use of this device outside the EU. If
applicable, check whether this device complies with local directives.
Maximum load: Never connect lights or equipment that exceed
the maximum load of the receiver, as it can result in defects, a short
circuit or fire.
Life-support: Never use Nexa products for life-support systems or
other applications in which equipment malfunctions can have life-
threatening consequences.
Interference: All wireless devices may be subject to interference,
which could affect performance. The minimum distance between 2
receivers should be at least 50 cm.
NNL
NEXA
Learn button LED indicator
Neutral
Neutral In
Live In Live Out
WIRING DIAGRAM
LCMR-1000
RELAY, 1 CHANNEL
TECHNICAL DATA
A declaration of conformity is available at www.nexa.se
LCMR-1000
Power source 220-240 V~50 Hz
Max. charge 2300 W / 10A
Frequency System Nexa (433.92 MHz)
Range up to 30 m
Storage locations 6
Power consumption < 1 W (standby)
Operating temperature 0-40 °C
IP rating IP20 Indoor use
Dimensions 53 x 53 x 25 mm
Built-in receiver for wireless control of lamps, etc. The receiver
needs both phase and neutral. The receiver is fully compatible with
other System Nexa products.
SAFETY
Read through the entire instruction first. Engage a professional if so
required. Nexa cannot be held liable if the product is used for any
purpose other than the one for which it is designed, or if there is
failure to comply with the instruction.
Never connect bulbs or equipment exceeding the receiver’s
maximum stated load – this may lead to faults, short-circuiting or
fire. Do not attempt to repair the product.
The product contains no repairable parts.
INSTALLATION
Make sure that the conductors are powered down by turning off
the power in the distribution box.
Connect LCMR-1000 as shown in the wiring diagram.
LINKING
To control LCMR-1000 using a System Nexa remote control (or
other device), the transmitter and receiver must be linked as follows:
1. Power up LCMR-1000
2. Press the learn button, the LED indicator starts to flash slowly
3. Press the “ON” button for the selected channel on a System
Nexa remote control within 18 seconds
See the instructions for use for the product in question if you wish
to train other System Nexa devices (motion detector, magnetic
contact, bridge, etc.)
LINKING CONFIRMATION
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
DELETING A STORAGE LOCATION
1. Power up LCMR-1000
2. Press the learn button, the LED indicator starts to flash slowly
3. Press the “OFF” button for the selected channel to be deleted on
a System Nexa remote control within 18 seconds.
See the instructions for use for the product in question if you wish
to delete other System Nexa devices (motion detector, magnetic
contact, bridge, etc.)
DELETION CONFIRMATION
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
ENGLISH
DELETING ALL STORAGE LOCATIONS.
1. Power up LCMR-1000
2. Press and hold down the learn button for 6 seconds, the LED
indicator starts to flash quickly
3. Release the learn button and then press it again briefly.
CONFIRMATION OF DELETION OF ALL STORAGE LOCATIONS
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
STORAGE:
LCMR-1000 has 6 storage locations and can be controlled from up
to 6 different devices (remote controls, motion detectors, magnetic
contacts, bridges, etc.). If all storage locations are occupied, it is not
possible to train a new device without deleting a storage location
first: see “DELETING A STORAGE LOCATION”
CONTROL
The receiver can be controlled in a number of ways.
1. With a trained System Nexa remote control
2. With other trained System Nexa transmitters
3. With a Nexa Bridge
FUSE
LCMR-1000 is provided with a glass tube fuse, 250V/T5A, which
provides overload protection. If the fuse is broken, check the
connected device for faults or short-circuit first before replacing the
fuse and powering LCMR-1000 back up.
NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN
Repairing: Do not attempt to repair this product. There are no user-
serviceable parts inside.
Water-resistance: This product is not water-resistant. Keep it dry.
Moisture will corrode the inner electronics and can result in a short
circuit, defects and shock hazard.
Cleaning: Use a dry cloth to clean this product. Do not use harsh
chemicals, cleaning solvents, or strong detergents.
Environment: Do not expose the product to excessive heat or cold,
as it can damage or shorten the life of electronic circuit boards.
OTHER INFORMATION
Indoor range: up to 30 m (optimal conditions). The range is strongly
dependent on local conditions, such as the presence of metals. For
example, the thin metal coating in Low-emissivity (Low-E) glass has
a negative impact on the range of radio signals.
There may be restrictions on the use of this device outside the EU. If
applicable, check whether this device complies with local directives.
Maximum load: Never connect lights or equipment that exceed
the maximum load of the receiver, as it can result in defects, a short
circuit or fire.
Life-support: Never use Nexa products for life-support systems or
other applications in which equipment malfunctions can have life-
threatening consequences.
Interference: All wireless devices may be subject to interference,
which could affect performance. The minimum distance between 2
receivers should be at least 50 cm.
NNL
NEXA
Learn button LED indicator
Neutral
Neutral In
Live In Live Out
WIRING DIAGRAM
LCMR-1000
RELAY, 1 CHANNEL
TECHNICAL DATA
A declaration of conformity is available at www.nexa.se
LCMR-1000
Power source 220-240 V~50 Hz
Max. charge 2300 W / 10A
Frequency System Nexa (433.92 MHz)
Range up to 30 m
Storage locations 6
Power consumption < 1 W (standby)
Operating temperature 0-40 °C
IP rating IP20 Indoor use
Dimensions 53 x 53 x 25 mm
Built-in receiver for wireless control of lamps, etc. The receiver
needs both phase and neutral. The receiver is fully compatible with
other System Nexa products.
SAFETY
Read through the entire instruction first. Engage a professional if so
required. Nexa cannot be held liable if the product is used for any
purpose other than the one for which it is designed, or if there is
failure to comply with the instruction.
Never connect bulbs or equipment exceeding the receiver’s
maximum stated load – this may lead to faults, short-circuiting or
fire. Do not attempt to repair the product.
The product contains no repairable parts.
INSTALLATION
Make sure that the conductors are powered down by turning off
the power in the distribution box.
Connect LCMR-1000 as shown in the wiring diagram.
LINKING
To control LCMR-1000 using a System Nexa remote control (or
other device), the transmitter and receiver must be linked as follows:
1. Power up LCMR-1000
2. Press the learn button, the LED indicator starts to flash slowly
3. Press the “ON” button for the selected channel on a System
Nexa remote control within 18 seconds
See the instructions for use for the product in question if you wish
to train other System Nexa devices (motion detector, magnetic
contact, bridge, etc.)
LINKING CONFIRMATION
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
DELETING A STORAGE LOCATION
1. Power up LCMR-1000
2. Press the learn button, the LED indicator starts to flash slowly
3. Press the “OFF” button for the selected channel to be deleted on
a System Nexa remote control within 18 seconds.
See the instructions for use for the product in question if you wish
to delete other System Nexa devices (motion detector, magnetic
contact, bridge, etc.)
DELETION CONFIRMATION
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
ENGLISH
DELETING ALL STORAGE LOCATIONS.
1. Power up LCMR-1000
2. Press and hold down the learn button for 6 seconds, the LED
indicator starts to flash quickly
3. Release the learn button and then press it again briefly.
CONFIRMATION OF DELETION OF ALL STORAGE LOCATIONS
The relay in LCMR-1000 click 4 times, and any connected lamp
flashes twice.
STORAGE:
LCMR-1000 has 6 storage locations and can be controlled from up
to 6 different devices (remote controls, motion detectors, magnetic
contacts, bridges, etc.). If all storage locations are occupied, it is not
possible to train a new device without deleting a storage location
first: see “DELETING A STORAGE LOCATION”
CONTROL
The receiver can be controlled in a number of ways.
1. With a trained System Nexa remote control
2. With other trained System Nexa transmitters
3. With a Nexa Bridge
FUSE
LCMR-1000 is provided with a glass tube fuse, 250V/T5A, which
provides overload protection. If the fuse is broken, check the
connected device for faults or short-circuit first before replacing the
fuse and powering LCMR-1000 back up.
NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN
Repairing: Do not attempt to repair this product. There are no user-
serviceable parts inside.
Water-resistance: This product is not water-resistant. Keep it dry.
Moisture will corrode the inner electronics and can result in a short
circuit, defects and shock hazard.
Cleaning: Use a dry cloth to clean this product. Do not use harsh
chemicals, cleaning solvents, or strong detergents.
Environment: Do not expose the product to excessive heat or cold,
as it can damage or shorten the life of electronic circuit boards.
Other manuals for LCMR-1000
1
Table of contents
Other Nexa Relay manuals
