Nexcom Nsa 5190 User manual

NEXCOM International Co., Ltd.

Published February 2024 www.nexcom.com

Network and Communication Solutions

Network Security Appliance

NSA 5190

User Manual

Content

Contents

Preface

Disclaimer.............................................................................................. iv

Acknowledgements ............................................................................... iv

Regulatory Compliance Statements........................................................ iv

Declaration of Conformity...................................................................... iv

RoHS Compliance ................................................................................... v

Warranty and RMA ................................................................................ vi

Safety Information ................................................................................viii

Installation Recommendations...............................................................viii

Safety Precautions.................................................................................. ix

Technical Support and Assistance............................................................ x

Conventions Used in this Manual............................................................ x

Global Service Contact Information........................................................ xi

Package Contents.................................................................................xiii

Ordering Information ............................................................................xiv

Chapter 1: Product Introduction

Overview ................................................................................................1

Key Features ...........................................................................................1

Hardware Specifications..........................................................................2

Knowing Your NSA 5190 ........................................................................3

Front Panel ..........................................................................................3

Rear Panel ...........................................................................................4

Mechanical Dimensions...........................................................................5

Chapter 2: Jumpers and Connectors

Before You Begin ....................................................................................5

Precautions ............................................................................................5

Jumper Settings ......................................................................................6

Locations of the Jumpers and Connectors...............................................7

Jumper ...................................................................................................8

CMOS Clear/AT_ATX .........................................................................8

Internal Connectors ................................................................................9

BIOS Socket (for SPI Flash) ...................................................................9

Power Switch ......................................................................................9

FAN Slot ........................................................................................10

SATA Power Connector .................................................................11

M.2 Key M Connector (Optional) ...................................................12

PCIe Slot (For Nexcom LAN Module)...............................................13

PCIe Slot (For NVMe Device only) ...................................................15

SATA Gen3 Connector.......................................................................17

Locations of the Front Panel Board Connectors .....................................18

Console Port .....................................................................................19

LAN Port............................................................................................19

LED Indicators ...................................................................................20

Reset Button .....................................................................................21

USB 3.0 Ports ....................................................................................21

Block Diagram ......................................................................................22

Content

Chapter 3: BIOS Setup

About BIOS Setup.................................................................................23

When to Configure the BIOS.................................................................23

Default Configuration...........................................................................24

Entering Setup......................................................................................24

Legends................................................................................................24

BIOS Setup Utility..................................................................................26

Main .................................................................................................26

Advanced .........................................................................................27

Chipset .............................................................................................39

Security .............................................................................................42

Boot..................................................................................................44

Save & Exit ........................................................................................45

Preface

PrefaCe

This publication, including all photographs, illustrations and software, is

part of this manual may be reproduced, copied, translated or transmitted in

any form or by any means without the prior written consent from NEXCOM

International Co., Ltd.

Disclaimer

The information in this document is subject to change without prior notice and

does not represent commitment from NEXCOM International Co., Ltd. However,

users may update their knowledge of any product in use by constantly checking

its manual posted on our website: http://www.nexcom.com. NEXCOM shall

not be liable for direct, indirect, special, incidental, or consequential damages

arising out of the use of any product, nor for any infringements upon the rights

of third parties, which may result from such use. Any implied warranties of

merchantability or fitness for any particular purpose is also disclaimed.

Acknowledgements

NSA 5190 are trademarks of NEXCOM International Co., Ltd. All other

product names mentioned herein are registered trademarks of their

respective owners.

Regulatory Compliance Statements

This section provides the FCC compliance statement for Class A devices and

describes how to keep the system CE compliant.

Declaration of Conformity

FCC

This equipment has been tested and verified to comply with the limits for

a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference

to radio communications. Operation of this equipment in a residential area

(domestic environment) is likely to cause harmful interference, in which

case the user will be required to correct the interference (take adequate

measures) at their own expense.

The product(s) described in this manual complies with all applicable

European Union (CE) directives if it has a CE marking. For computer systems

to remain CE compliant, only CE-compliant parts may be used. Maintaining

CE compliance also requires proper cable and cabling techniques.

Preface

RoHS Compliance

NEXCOM RoHS Environmental Policy and Status

Update

NEXCOM is a global citizen for building the digital

infrastructure. We are committed to providing green

products and services, which are compliant with

European Union RoHS (Restriction on Use of Hazardous Substance in

Electronic Equipment) directive 2011/65/EU, to be your trusted green

partner and to protect our environment.

RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg)

< 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent

Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) <

0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or

1,000ppm.

In order to meet the RoHS compliant directives, NEXCOM has established an

engineering and manufacturing task force in to implement the introduction

of green products. The task force will ensure that we follow the standard

NEXCOM development procedure and that all the new RoHS components

and new manufacturing processes maintain the highest industry quality

levels for which NEXCOM are renowned.

The model selection criteria will be based on market demand. Vendors and

suppliers will ensure that all designed components will be RoHS compliant.

How to recognize NEXCOM RoHS Products?

For existing products where there are non-RoHS and RoHS versions, the

suffix “(LF)” will be added to the compliant product name.

All new product models launched after January 2013 will be RoHS compliant.

They will use the usual NEXCOM naming convention.

Preface

Warranty and RMA

NEXCOM Warranty Period

NEXCOM manufactures products that are new or equivalent to new in

accordance with industry standard. NEXCOM warrants that products will be

free from defect in material and workmanship for 2 years, beginning on the

date of invoice by NEXCOM.

NEXCOM Return Merchandise Authorization (RMA)

▪Customers shall enclose the “NEXCOM RMA Service Form” with the

returned packages.

▪Customers must collect all the information about the problems

encountered and note anything abnormal or, print out any on-screen

messages, and describe the problems on the “NEXCOM RMA Service

Form” for the RMA number apply process.

▪Customers can send back the faulty products with or without accessories

(manuals, cable, etc.) and any components from the card, such as CPU

and RAM. If the components were suspected as part of the problems,

please note clearly which components are included. Otherwise, NEXCOM

is not responsible for the devices/parts.

▪Customers are responsible for the safe packaging of defective products,

making sure it is durable enough to be resistant against further damage

and deterioration during transportation. In case of damages occurred

during transportation, the repair is treated as “Out of Warranty.”

▪Any products returned by NEXCOM to other locations besides the

customers’ site will bear an extra charge and will be billed to the customer.

Repair Service Charges for Out-of-Warranty Products

NEXCOM will charge for out-of-warranty products in two categories, one is

basic diagnostic fee and another is component (product) fee.

System Level

▪Component fee: NEXCOM will only charge for main components such as

SMD chip, BGA chip, etc. Passive components will be repaired for free,

ex: resistor, capacitor.

▪Items will be replaced with NEXCOM products if the original one cannot

be repaired. Ex: motherboard, power supply, etc.

▪Replace with 3rd party products if needed.

▪If RMA goods can not be repaired, NEXCOM will return it to the customer

without any charge.

Board Level

▪Component fee: NEXCOM will only charge for main components, such

as SMD chip, BGA chip, etc. Passive components will be repaired for free,

ex: resistors, capacitors.

▪If RMA goods can not be repaired, NEXCOM will return it to the customer

without any charge.

Preface

Warnings

Read and adhere to all warnings, cautions, and notices in this guide and

the documentation supplied with the chassis, power supply, and accessory

modules. If the instructions for the chassis and power supply are inconsistent

with these instructions or the instructions for accessory modules, contact

the supplier to find out how you can ensure that your computer meets

safety and regulatory requirements.

Cautions

Electrostatic discharge (ESD) can damage system components. Do the

described procedures only at an ESD workstation. If no such station is

available, you can provide some ESD protection by wearing an antistatic

wrist strap and attaching it to a metal part of the computer chassis.

Preface

Installation Recommendations

Ensure you have a stable, clean working environment. Dust and dirt can get

into components and cause a malfunction. Use containers to keep small

components separated.

Adequate lighting and proper tools can prevent you from accidentally

damaging the internal components. Most of the procedures that follow

require only a few simple tools, including the following:

▪A Philips screwdriver

▪A flat-tipped screwdriver

▪A grounding strap

▪An anti-static pad

Using your fingers can disconnect most of the connections. It is recommended

that you do not use needle-nose pliers to disconnect connections as these

can damage the soft metal or plastic parts of the connectors.

Safety Information

Before installing and using the device, note the following precautions:

▪Read all instructions carefully.

▪Do not place the unit on an unstable surface, cart, or stand.

▪Follow all warnings and cautions in this manual.

▪When replacing parts, ensure that your service technician uses parts

specified by the manufacturer.

▪Avoid using the system near water, in direct sunlight, or near a heating

device.

▪The load of the system unit does not solely rely for support from the

rackmounts located on the sides. Firm support from the bottom is highly

necessary in order to provide balance stability.

▪The computer is provided with a battery-powered real-time clock circuit.

There is a danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type recommended by the manufacturer.

Discard used batteries according to the manufacturer’s instructions.

Preface

Safety Precautions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a

damp cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a stable surface during installation. Dropping it or

letting it fall may cause damage.

7. The openings on the enclosure are for air convection to protect the

equipment from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting

the equipment to the power outlet.

9. Place the power cord in a way so that people will not step on it. Do not

place anything on top of the power cord. Use a power cord that has been

approved for use with the product and that it matches the voltage and

current marked on the product’s electrical range label. The voltage and

current rating of the cord must be greater than the voltage and current

rating marked on the product.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the

power source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical

shock.

13. Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by

service personnel:

a. The power cord or plug is damaged.

b.Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d.The equipment does not work well, or you cannot get it to work

according to the user’s manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. Do not place heavy objects on the equipment.

16. The unit uses a three-wire ground cable which is equipped with a third

pin to ground the unit and prevent electric shock. Do not defeat the

purpose of this pin. If your outlet does not support this kind of plug,

contact your electrician to replace your obsolete outlet.

17. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY

REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE

RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES

ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.

Preface

Technical Support and Assistance

1. For the most updated information of NEXCOM products, visit NEXCOM’s

website at www.nexcom.com.

2. For technical issues that require contacting our technical support team or

sales representative, please have the following information ready before

calling:

– Product name and serial number

– Detailed information of the peripheral devices

– Detailed information of the installed software (operating system,

version, application software, etc.)

– A complete description of the problem

– The exact wordings of the error messages

Warning!

1. Handling the unit: carry the unit with both hands and handle it with care.

2. Maintenance: to keep the unit clean, use only approved cleaning products

or clean with a dry cloth.

Conventions Used in this Manual

Warning:

Information about certain situations, which if not observed,

can cause personal injury. This will prevent injury to yourself

when performing a task.

CAUTION!

CAUTION!CAUTION! Caution:

Information to avoid damaging components or losing data.

Note:

Provides additional information to complete a task easily.

Preface

Global Service Contact Information

Headquarters

NEXCOM International Co., Ltd.

9F, No. 920, Zhongzheng Rd.,

Zhonghe District, New Taipei City, 23586,

Taiwan, R.O.C.

Tel: +886-2-8226-7786

Fax: +886-2-8226-7782

www.nexcom.com

Asia

Taiwan

NexAIoT Headquarters

Industry 4.0 and Cloud Services

12F, No.922, Zhongzheng Rd.,

Zhonghe District, New Taipei City,

23586, Taiwan, R.O.C.

Tel: +886-2-8226-7796

Fax: +886-2-8226-7926

Email: [email protected]

www.nexaiot.com

NexAIoT Co., Ltd.

Taichung Office

16F, No.250, Sec.2, Chongde Rd.,

Beitun District,

Taichung City, 406, Taiwan, R.O.C.

Tel: +886-4-2249-1179

Fax: +886-4-2249-1172

Email: [email protected]

www.nexaiot.com

NexCOBOT Taiwan Co., Ltd.

13F, No.916, Zhongzheng Rd.,

Zhonghe District,

New Taipei City, 23586, Taiwan, R.O.C.

Tel: +886-2-8226-7786

Fax: +886-2-8226-7926

Email: [email protected]

www.nexcobot.com

GreenBase Technology Corp.

13F, No.922, Zhongzheng Rd.,

Zhonghe District,

New Taipei City, 23586, Taiwan, R.O.C.

Tel: +886-2-8226-7786

Fax: +886-2-8226-7900

Email: [email protected]

www.nexcom.com.tw

DivioTec Inc.

19F-1A, No.97, Sec.4, ChongXin Rd.,

Sanchong District,

New Taipei City, 24161, Taiwan, R.O.C.

Tel: +886-2-8976-3077

Email: [email protected]

www.diviotec.com

AIoT Cloud Corp.

13F, No.922, Zhongzheng Rd.,

Zhonghe District,

New Taipei City, 23586, Taiwan, R.O.C.

Tel: +886-2-8226-7786

Fax: +886-2-8226-7782

Email: [email protected]

www.aiotcloud.dev

EMBUX TECHNOLOGY CO., LTD.

13F, No.916, Zhongzheng Rd.,

Zhonghe District,

New Taipei City, 23586, Taiwan, R.O.C.

Tel: +886-2-8226-7786

Fax: +886-2-8226-7782

Email: [email protected]

www.embux.com

TMR TECHNOLOGIES CO., LTD.

13F, No.916, Zhongzheng Rd.,

Zhonghe District,

New Taipei City, 23586, Taiwan, R.O.C.

Tel: +886-2-8226-7786

Fax: +886-2-8226-7782

Email: [email protected]

www.tmrtek.com

Preface

NEXGOL Chongqing

1st Building No.999,

Star Boulevard, Yongchuan Dist,

Chongqing City, 402160, China

Tel: +86-23-4960-9080

Fax: +86-23-4966-5855

Email: [email protected]

www.nexcom.cn

Beijing NexGemo Technology Co.,Ltd.

Room 205, No.1, Fazhan Rd.,

Beijing International Information Industry Base,

Changping District,

Beijing, 102206, China

Tel: +86-10-8072-2025

Fax: +86-10-8072-2022

Email: [email protected]

www.nexgemo.com

Japan

NEXCOM Japan

9F, Tamachi Hara Bldg.,

4-11-5, Shiba Minato-ku,

Tokyo, 108-0014, Japan

Tel: +81-3-5419-7830

Fax: +81-3-5419-7832

Email: [email protected]

www.nexcom-jp.com

China

NEXSEC Incorporated

201, Floor 2, Unit 2, Building 15, Yard 3,

Gaolizhang Road, Haidian District,

Beijing, 100094, China

Tel: +86-10-5704-2680

Fax: +86-10-5704-2681

Email: [email protected]

www.nexsec.cn

NEXCOM Shanghai

Room 406-407, Building C, No 154, Lane 953,

Jianchuan Road, Minhang District,

Shanghai, 201108, China

Tel: +86-21-5278-5868

Fax: +86-21-3251-6358

Email: [email protected]

www.nexcom.cn

NEXCOM Surveillance Technology Corp.

Floor 8, Building B3, Xiufeng Industrial Zone,

GanKeng Community, Buji Street,

LongGang District,

ShenZhen, 518112, China

Tel: +86-755-8364-7768

Fax: +86-755-8364-7738

Email: [email protected]

www.nexcom.cn

America

USA

NEXCOM USA

46665 Fremont Blvd.,

Fremont CA 94538, USA

Tel: +1-510-656-2248

Fax: +1-510-656-2158

Email: [email protected]

www.nexcomusa.com

Preface

Package Contents

Before continuing, verify that the NSA 5190 package that you received is

complete. Your package should have all the items listed in the following table.

Item Part Number Name Qty

1 19S00519000X0 NSA5190 ASSY 1

2 6014606898X00 LABEL BLANK WAI GHA 2

3 6019900094X00 PARTITION FOR RODS-HTQ-A-2AC VER:B FULPAK 1

4 6030000350X00 CONSOLE CABLE ST:ST-1903024 1

5 Z300000040X00 OUTSIDE BOX LABEL FOR STANDARD VER.A 1

6 5040210058X00 EAR SET FOR ODS-VL3 SERIES VER:A CHYUAN-JYH 1

7 50311F0684X00 I HEAD SCREW FOR nROK6221-IPAI BLACK PANEL LONG FEI 6

8 6013301929X00 EPE FOR NSA5190 FRONT BOTTOM VER:A TSAIJIN 1

9 6013301930X00 EPE FOR NSA5190 FRONT TOP VER:A TSAIJIN 1

10 5044440031X00 RUBBER FOOT KANG YANG:RF20-5-4P 4

11 6013301931X00 EPE FOR NSA5190 REAR BOTTOM VER:A TSAIJIN 1

12 6013301932X00 EPE FOR NSA5190 REAR TOP VER:A TSAIJIN 1

13 60110A0229X00 ACCESSORY BOX FOR S2216/S2224 VER:A YI GIA 1

14 60111B0072X00 OUTSIDE CARTON FOR NSA3170A-OS1 VER:B YI GIA 1

15 601110A126X00 OUTSIDE CARTON FOR FTA5180 VER:A YI GIA 1

16 6012200053X00 PE ZIPPER BAG #3 炎洲:印刷由任袋3號1

17 6012200096X00 PE BAG FOR UTM625 VAR:A CHYUAN-JYH 1

Preface

Ordering Information

The following information below provides ordering information for NSA 5190.

Barebone

• NSA 5190 (P/N: 10S00519000X0)

1U w/ 12th/13th Gen Intel®Core™ processor, 2 x 1GbE RJ45 ports, and 4 x LAN module slots

For optimal performance, the configuration of LAN modules below is recommended.

Model P/N Controller Interface Port Number Bypass Speed Location Slot*

NI 180C 2BQ000ODS13X1 i350AM4 x 2 PCIe 8 x RJ45 None 1 GbE 3, 4

NI 184CX1 2BQ000ODS14X1 i350AM4 x 2 PCIe 8 x RJ45 4 1 GbE 3, 4

NX 140F 2BQ000ODS11X1 XL710-BM1 PCIe 4 x SFP+ None 10 GbE 1, 2

NX 142FX1 2BQ000ODS15X1 XL710-BM1 PCIe 4 x LC 2 10 GbE 1, 2

NX 142FX1-LR 2BQ000ODS16X1 XL710-BM1 PCIe 4 x LC 2 10 GbE 1, 2

NV 120F 2BQ000ODS17X1 XXV710-AM2 PCIe 2 x SFP28 None 25 GbE 1, 2

* Refer to the image below for the location of slots.

1 2 3 4

** To check the availability of other compatible LAN modules, please contact your responsible NEXCOM account manager or fill in the online inquiry form.

Chapter 1: Product Introduction

ChaPter 1: ProduCt IntroduCtIon

Overview Key Features

▪12th/13th Gen Intel®Core™ processor

▪4 x DDR4 2666/3200 non-ECC/ECC UDIMM, up to 128GB

▪1 x M.2 2280 M key NVMe SSD (optional)

▪1 x PCIe 4.0 x8 connector for low profile riser card

▪2 x 1GbE RJ45 ports

▪4 x LAN module slots

Chapter 1: Product Introduction

Hardware Specifications

Main Board

▪12th/13th Gen Intel®Core™ processor, formerly Alder Lake S/Raptor

Lake S, max 65W

▪PCH: R680E

▪TPM 2.0 onboard

Main Memory

▪4 x DDR4 2666/3200 non-ECC/ECC UDIMM with up to 32GB per slot

(max. up to 128GB)

Storage

▪1 x M.2 2280 Key M PCIe 3.0 x4 NVMe SSD, up to 512GB (optional)

Interface-External

▪2 x Buttons: power/reset

▪4 x LEDs: PWR1/PWR2/FAN/SYS

▪2 x USB 3.0 ports

▪1 x RJ45 console port

▪2 x 1GbE RJ45 ports

▪4 x LAN module slots (see details)

▪3 x Swappable smart fans

▪2 x Power inlets for redundant PSU

Interface-Internal

▪1 x PCIe 4.0 x8 connector, limited support for low-profile riser cards and

is exclusively for NVMe storage card (optional, see details)

Power Input

▪550W CRPS (1+1) redundant PSU

Dimensions and Weight

▪Chassis dimension (W x D x H): 438 x 511 x 44 mm

▪Packaging size: 675 x 635 x 217 mm

▪Weight without packaging: 9.97 kg

▪Weight with packaging: 18.09 kg

Environment

▪Operating temperature: 0°C~40°C

▪Storage temperature: -20°C~80°C

▪Relative humidity: 10%~90% non-condensing

Certifications

▪CE/FCC Class A

▪LVD

Chapter 1: Product Introduction

Knowing Your NSA 5190

Front Panel

1 2 4

3 5 6 7 8 9

1. Reset Pin Hole

Reset the system by using a paperclip to press and hold the pinhole for a

few seconds.

2. LED Indicators

Indicate the FAN, SYS, PWR1, and PWR2.

3. RJ45 Type Console Serial Port

Used to connect a console device with RJ45 type connection.

4. USB 3.0 Ports

Used to connect USB 3.0/2.0/1.1 devices.

5. LAN Ports

Used to connect to a network.

6. LAN Slot 1*

7. LAN Slot 2*

8. LAN Slot 3*

9. LAN Slot 4*

LAN Slot 1 LAN Slot 2 LAN Slot 3 LAN Slot 4 PCIe5 (Internal for NVMe)

Connector Type PCIe 4.0 x8 PCIe 4.0 x8 PCIe 4.0 x8 PCIe 4.0 x8 PCIe 4.0 x8

Signal PCIe 4.0 x8 PCIe 4.0 x8 PCIe 4.0 x4

PCIe 4.0 x4

PCIe 3.0 x4

PCIe 4.0 x4

Chapter 1: Product Introduction

Rear Panel

121110

10. Swappable Smart Fans

11. Power Button

Press to power on or off the system.

12. AC Power Inlets

Connect each AC cord to the dual redundant power inlets.

Chapter 1: Product Introduction

Mechanical Dimensions

Chapter 2: Jumpers and Connectors

ChaPter 2: JumPers and ConneCtors

This chapter describes how to set the jumpers and connectors on the

NSA 5190 motherboard.

Before You Begin

▪Ensure you have a stable, clean working environment. Dust and dirt can

get into components and cause a malfunction. Use containers to keep

small components separated.

▪Adequate lighting and proper tools can prevent you from accidentally

damaging the internal components. Most of the procedures that follow

require only a few simple tools, including the following:

– A Philips screwdriver

– A flat-tipped screwdriver

– A set of jewelers screwdrivers

– A grounding strap

– An anti-static pad

▪Using your fingers can disconnect most of the connections. It is

recommended that you do not use needle-nosed pliers to disconnect

connections as these can damage the soft metal or plastic parts of the

connectors.

▪Before working on internal components, make sure that the power is off.

Ground yourself before touching any internal components, by touching

a metal object. Static electricity can damage many of the electronic

components. Humid environments tend to have less static electricity than

dry environments. A grounding strap is warranted whenever danger of

static electricity exists.

Precautions

Computer components and electronic circuit boards can be damaged by

discharges of static electricity. Working on computers that are still connected

to a power supply can be extremely dangerous.

Follow the guidelines below to avoid damage to your computer or yourself:

▪Always disconnect the unit from the power outlet whenever you are

working inside the case.

▪If possible, wear a grounded wrist strap when you are working inside the

computer case. Alternatively, discharge any static electricity by touching

the bare metal chassis of the unit case, or the bare metal body of any

other grounded appliance.

▪Hold electronic circuit boards by the edges only. Do not touch the

components on the board unless it is necessary to do so. Don’t flex or

stress the circuit board.

▪Leave all components inside the static-proof packaging that they shipped

with until they are ready for installation.

▪Use correct screws and do not over tighten screws.

Table of contents

Popular Rack & Stand manuals by other brands

Onn

Onn ONA16TM009 Product guide

Manfrotto

Manfrotto 127 instructions

FONESTAR

FONESTAR SVW-134BV quick start guide

Echogear

Echogear ECHO-GM2FC instruction manual

Kohler

Kohler MEMOIRS K-6880 Installation and care guide

CHIEF

CHIEF LCD2C installation instructions

ECG

ECG LD 326501 instruction manual

Alvin

Alvin WRF38 Assembly instruction

Conrad Electronic

Conrad Electronic 41 60 80 operating instructions

AllMounts

AllMounts PLB-43S instruction manual

Bechara

Bechara PRESTIGE Product Guide and Assembly Instructions

Draper

Draper Revelation operating instructions

Pioneer

Pioneer CP-ST100 manual

Medrad

Medrad Ceiling Mount Plate Placement Considerations and Installation Requirements

KSL

KSL WM112T Quick installation guide

CHIEF

CHIEF SL-150 instruction manual

Vivo

Vivo MOUNT-PC01 instruction manual

Scanstrut

Scanstrut SC-SL-01 manual

Nexcom NSA 5190 User manual

Popular Rack & Stand manuals by other brands