Next NEXT600-S User manual

NEXT600-S
peristaltic pump User Manual

NOTED：
Warning：
!
!
Due to the wear, may cause the tube cracks. If it happened,
the liquid will overflow from the tube, then may damage the human
body and equipment, so please often check and timely replace the
tube!
Please ensure plug the power cord directly into a wall outlet,
and to avoid the use of extension cords
If the power cord or plug became frayed or have other
damaged, please unplug the power plug (pull out the plug but not
the power cord)
If the following condition occurs, turn off the power and pull
out the plug (pull out the plug but not the power cord):
1. The liquid is spilled on the unit.
2. When you think the machine needs maintenance or repair.
Customer's power outlet must have a reliable earth ground
Please ensure the power was off, when you want to load or
unload the foot switches and other external controllers, to avoid the
external control interface's burning.
Before operating, please read this User Manual carefully.

Product Introductions
Operation Panel
Menu Descriptions
Operating instructions
Technical Parameters
Suitable Pump Heads & Tubes
External Interface
Functions & Features
Flow Rate Descriptions
Pump Tubes Descriptions
Pump Tubes Parameters
Maintenance, Warranty & Service
1
2
3
5
6
7
8
10
9
11
9
12
TABLE OF CONTENTS

Two kinds of operating modes, transferring and dispensing, can be switched
freely, to ensure the quantitative distribution of the fluid.
Applicable pump heads: YZ35, YZ35-13.
With both-way large torque, low power motor. It can be connected with
several pump heads to satisfy the different demands of the flow rates.
FULL SPEED button available for filling in & emptying out the tubing quickly.
Long life, digital rotary knob; the revolving speed can be continuously
adjusted by hand, or to preset distribution frequency, time, interval and back
suction angle.
Memory function available in case of power off and it will continue the work
once the power was restarted.
Supports MODBUS communication protocol through the DB15 interface of
the drive. And communication protocols customized is available.
Good cost performance.
With liquid calibration, flow rates dispensing displaying function.
Digital dispensing type pumps
1
PRODUCT INTRODUCTION
▲
▲
▲
▲
▲
▲
▲
1 . 3 ~ 1 2 0 0 0 m l / m i n
Digital distribution type pump--NEXT600-S
Velocity range
A
Typical applications:
◆Glue dispensing ◆Water sampling
◆For liquid chromatography
◆Multi channel transmission is widely used in bulk liquid
HOT
Products
▲
B
E
F
C
D
High-precision
Digital type
A drive B pump head
C power switch D control
interface
E built-in fuse F power socket
-
-
-
-
-
-
-
Note: the use of external control and see page 8

2
LED DISPLAY INTERFACE
4-LED DISPLAY
SPEED
DIRECTION LITER/ ML/ MIN/ SEC/
EXTERNAL
CONTROL
MENU
L/
ml/ sec
min
rpm
T
FILLING NUMBERS
WO RK S TA TE
Peristaltic pump operating panel
The peristaltic pump is composed of three parts: driver, pump head, pump assembly is simple,
easy to understand.
This manual will provide various parameters of peristaltic pump value and operation method for
you.
To provide comprehensive services in all aspects for you
SCHEMA T I C D I A G R A M O F P U M P
一 二 三
Peristaltic pump characteristics
NO POLLUTION / WITHOUT CLEANING / LOW SHEAR / EASY
MAINTENANCE / WIDE APPLICATION RANGE
NE X T6 0 0- SNE X T6 0 0- S
4 color LED display
Speed, velocity
Speed / full speed knob
Left / right / stop switch

CHOOSE THE DISPLAY MODE
C0-0 0-5 v
C0-1 0-1 0 v
C0-2 4-20MA
C0-3 0-10KHz
C0-4
I N T E R N A L C O N T R O L
( D E F A U L T )
E-CONTROL AND SYSTEM SETTING
SP E E D
FLOWRATE
SPEED CONTROL MODE
START /STOP CONTROL MODE
C1-0
INTERNAL CONTROL
(DEFAULT)
C2-0 EXTERNAL CONTRA
C1-1 EXTERNAL CONTROL
C2-1
I N T E R N A L C O N T R O L
( D E F A U L T )
DIRECTION MODE
START/STOP SIGNAL MODE
BOOT DISPLAY：DEVICE ADDRESS
(1～32)
ESC (EXIT)
ESC (EXIT)
ESC (EXIT)
3
Pump menu function definition
When choosing (speed display mode) can
open the options menu (set, external control
system)
When choosing (flow) model can open the
options menu (set, external control system),
(pump head pump set), (calibration)
A0-0
A1
A0-1
A1
A2 E0
Remarks Explain
Operating instructions
Start-stop direction control
Speed 󰾬󰾬function
Menu Operation function
Full speed function
Reversible left - stop - right switch place in the "left", the pump running at
setting speed counterclockwise; place in the "right", the pump running at
setting speed clockwise; place in "stop" the pump stop running.
Speed 󰾬󰾬control knob turn clockwise, LED speed/flow display increase;
counterclockwise rotation speed control knob, LED speed/flow display
decrease.
Press the knob to enter the menu operation when the pump stops; turn the
knob to select the appropriate options, and then press the knob to confirm.
When the pump running at speed mode, press the button at full speed, pump
will run at maximum speed 100rpm, displaying "100", to complete the quick
emptying, filling or cleaning operations; release the full speed button, the
pump will back to the previous state.
◆

Co-0
RS485 DISALE
(DEFAULT )
C o -1485 ENABLE
R s 4 8 5 E N A B L E
Cb-0 （0-5v）(DEFAULT)
Cb-1
Cb-2
（0-10v）
（0-10KHz）
EXTERNAL CONTROL OUTPUT
Cb-3
（4-20MA）
Cb-4 N O O U T P U T
Cc-0 （RETURN TO FACTORY SETTING）
RETURN TO FACTORY SETTING
PUMP HEAD & TUBE SETTING
（NOTE: THIS MENU IN THE FLOW MODE DISPLAY）
PUMP HEAD SETTING
A200 （Yz1515x ）DEFAULT
A201
A202
（Bz15）
（313D）
A203 （ ）Yz2515x
A204
（Bz25）
A205 Dg（6）
C4-0
C4-1
10～300（10 RPM DEFAULT ）
SUCTION SPEED
( RESOLUTION 1 RPM)
C5-1 S T A R T
INITIAL STATUS
C5-0 STOP (DEFAULT)
Device address
24 0 0
9600(DE F A ULT)
BA U D R A TE
12 0 0
48 0 0
SUCTION ANGLE
( RESOLUTION 1 .)
NO SUCTION(DEFAULT)
10-720 CAN CHOOSE
-01-CHOOSE THE ADDRESS IS NO.1
-30- CHOOSE THE ADDRESS IS NO.30
.. . .. .. ..
C3-0 LE V E L ( DE F A U L T )
C 3 -1 P U L S E
SIGNAL FUNCTION MODE
Cd-0
Cd-1
（ ）
（ ）
ESC (EXIT)
EXTERNAL START/
STOP CONTROL CHOOSE
external start/stop control
cable No. 1 is avaible
external start/stop control
cable No. 2 is avaible
ESC (EXIT)
ESC (EXIT)
ESC (EXIT)
ESC (EXIT)
ESC (EXIT)
ESC (EXIT)
ESC (EXIT)
ESC (EXIT)
ESC (EXIT)
ESC (EXIT)
FALLING /SHORT CONNECT ADGE
RISING ADGE/DISCONNECT
4

5
Pump parameter table
Input calibration：0.001ml～999L
Range units
0.001-9.99 9 0 .001
10 -99.9 9 0 .0 1
Resolution
mL
10 0 -999.9 0 .1
100.0-999.9 0.1
10 .00-99.9 9 0 .0 1
10 0 0 -9 999 1
10 0 0 -9 999 1
L
L
L
mL
mL
mL
Measured liquid input：0.001ml～999L
Range units
0.001-9.99 9 0 .001
10 -99.9 9 0 .0 1
Resolution
mL
mL
100-99 9 .9 0 .1
100.0-999.9 0.1
10 .00-99.9 9 0 .0 1
1000-99 9 9 1
1000-99 9 9 1
mL
mL
L
L
L
CALIBRATION FUNCTION
E S C E E X I T
VOLUME CALIBRATION( ESC IS EXIT )
ENTER THE ACTUAL VOLUME (ESC IS EXIT )
PRESS THE KNOB TO CONFIRM
DIRECTION (REPEATED OPERATION)
-
-
-
-
-
-
-
Tube and calibration parameter
are on the Parameter table.
-0.5- 0 5（ . ID）
-13- 13（ #）
ESCE （EXIT）
TUBE SETTING
Dg（10）
A206
A207
KZ25
A208 Yz35
A209
ESCE （EXIT）
Kz35
sec
⑸Rotate the knob to the
⑷To rotate and press the knob (return to the main interface).
⑵Press the knob to enter (and rotate speed display mode).
sec
⑴Press the button to enter the (display of choice).
sec
⑹The According to the operation of the peristaltic pump 80rpm/min
Application one: speed mode transmission
Transmission fluid to rotate speed of 80rpm/min.
⑶Press the knob to determine the current model for the speed display mode.
Application three: calibration fluid
Application two: flow mode transmission
Transmission fluid to rotate speed of 80ml/min.
sec
⑸Rotate the knob to the
⑷To rotate and press the knob (return to the main interface).
sec
⑹The peristaltic pump according to the 80ml/min operation
⑶Press the knob to determine the current model for the flow pattern.
⑴Press the button to enter the (display of choice).
⑵Press the knob and rotate to enter (flow).
sec
With 8 ml/min speed transmission fluid.
(1)Turn the oeristaltic pump to flowrate mode
(2)Customers can choose right pump head and tube. For
example, user choose YZ1515X pump head and 13# tube, need
to enter choose A200, then enter choose -13-
(3)Return main interface,adjust the flowrate as 8ml/min.
if the flowrate not precise, user can use calibration
function to adjust.
(4)Enter to displaying 8ml
(5)Pull ,peristaltic pump will transfer liquid and auto
stop when reach the set time, and metering and store the
liquid volume.
(6)Pull to stop position,displaying 8.000.Use the digital
knob to input the actual calibrtation volume .
(7)Then press the knob to the mian interface.

6
Technical specifications
Technical guidance
NE X T 6 00-S
Driver
Model
Technical
parameters
Part of the pump head and pump
Optional pump head, pump type
SUITABLE PUMP HEAD & FLOWRATE REFERENCE
TU B E
MO D E
DRIVE
MODE
NEXT600-S
-
-
-
-
Note: the use of the pump head to see the pump head vser manual.
-
-
-

7
-15- -7 3 -
-24- -8 2 -
15# DEFAULT 73# DEFAULT
24 # 82#
A204 A208
（BZ25） （YZ35）
-0.5- -0.5-
-1.0- -1.0-
-2.0- -2.0-
0.5*0.8 DEFAULT 0.5*0.8 DEFAULT
1*1 1 *1
2*1 2 *1
A205 A206
（DG6） （Dg10）
-2.4- -2.4-
-3.0- -3.0-
-4.8- -4.8-
2.4*0.8 2 .4*0.8
3*1 3 *1
4.8*1 4 .8*1
Pump Head Tube Corresponding To The Table
-13- -1 3 -
-14- -1 4 -
13# DEFAULT 13# DEFAULT
14 # 14 #
A200 A201
（YZ1515x） （BZ15）
-16- -1 6 -
-18- -1 8 -
-17- -1 7 -
-19- -1 9 -
-25- -2 5 -
16 # 16 #
18 # 18 #
17 # 17 #
19 # 19 #
25 # 25 #
-13- -1 5 -
-14- -2 4 -
13# DEFAULT 15# DEFAULT
14 # 24 #
A202
（KZ3D）
-16- -3 5 -
-18-
-17- -3 6 -
-19-
-25-
16 # 35 #
18 #
17 # 36 #
19 #
25 #
A203
（YZ2515x）
The pursuit of excellence
The creation of customer value
PUMP HEAD MODE PUMP HEAD MODE TUBE NO TUBE NO TUBE MODE TUBE MODE
The pursuit of excellence
The creation of customer value

8
-15- -8 6 -
-24- -9 0 -
-35- -8 8 -
15# DEF A U L T 86# DEFAULT
2 4 # 9 0 #
3 5 # 8 8 #
A207 A209
（KZ25） （KZ35）
-36- -9 2 -3 6 # 9 2 #
Series driver control needs to answer the pin
1 9 2 10 3 11 4 12 5 13 6 14 7 15 8
EXTERNAL CONTROL INTERFACE DIAGRAM
THE EXTERNAL CONTROL
PIN PARAMETER TABLE
The pursuit of excellence
The creation of customer value
E-CONTROL INPUT INTERFACE DEFINITION
INPUT WIRE COLOR
The pursuit of excellence
The creation of customer value

9
DRIVE EXTROCONTROL INTERFACE (DB-15) DESCRIPTION
15-pin connector on the back of the machine is done by an external signal to
control the machine interface. First prepare a DB15 connector (hole), and
several different colors of the signal cable to the 15-pin female connector to
open, according to the following sequence diagram welding wire signal lines of
different colors, and the signal lines 15-pin connector clip line fixed together, if
necessary, can be reinforced plastic injection, and finally installed on the shell
screws.
-
-
-
-
-
-
-
Functions And Features
The Reference Flow Diagram
Note :1 ,External control line is optional
2 ,If the wire less than 8 pcs ,the final 2 use for RS485 : for example :black is
E-C ground ,red is start/stop. yellow&green are 485 (5 wires)
3,External wire operation guide : A)enable and ground wire connect and
disconnect ,to control enter or exit the external control
B)start/stop 1 and ground wire connect and disconnect, to control the stop
and start ; start/stop2 and ground wire connect and disconnect ,to check if
there is voltage signal to control the start/stop .
C)Direction and ground wire connect and disconnect , to control the pump’s
direction
D)Between the Speed and ground will connect to the 0-5v 0-10v 4-20ma 0-
10khz …control signal .
--------------------- --------------------- --------------------- --------------------- --------------------- ---------------------
10
15
100 200 300 400 500 6000
73# 7.4L
82# 1 2 L
5
YZ35-13、YZ35
More information
warm reminding:
Please select suitable type and
texture tubes, to guarantee the
optimum performance of the
p e r i s t a l t i c p u m p s . P l e a s e
contact our customer service in
case any questions, thanks.
(rpm/min)
(ml/min)
Applicable pump heads: YZ35-13, YZ35.
Rotating speed stepless regulation, may adjust speed by hand through rotary
knobs, or automatic control through external control interface, easy operation
and intuitive.
To adjust the rotating speed by rotary knob, it is better than by membrane
keypad in reducing the failure rates during the operation procedure.
FULL SPEED button available for filling in & emptying out quickly.

10
-------------------------------------------------
----------------------------------------------
----------------------------------------------
------- ----- ----------- ----- ----------- ----- ----
------- ----- ----------- ----- ----------- ----- ----
Import Hose And Its Characteristics
◆C h e m i c a l
resistance
Resistant to strong
acid (such as
c o n c e n t r a t e d
s u l f u r i c a c i d
concentration of
98%), the majority
of highly corrosive
organic solvents
◆Advantage
◆Application
Excellent abrasion
resistance, anti fatigue,
anti ultraviolet aging
resi stanc e o zone
resistance, oxidation
resistance,evenif long-
term exposure tohigh
temperature and ozone aging
environment,will not
crack.
Ink and long time of
peristaltic pump liquid
transport, can be long-term
used for various gaskets,
wear casing andinsulated
cable.
◆Advantage
◆Application
Anti-aging, anti-oxidant,
wall to prevent the
accumulation of smooth, easy
to clean
Chemical analysis instruments
with a hose, can withstand
almost all commonly used
laboratory inorganic
chemicals, can be used as a
condenser, incubators,
trachea, drains, peristaltic
hose pumps and other
experiments.
Tygon F-4040-A
◆Advantage
Tygon fuel and lubricant
supply pipe can resist
swelling and hardening caused
due to hydrocarbon-based
fluids, specially designed and
manufactured, do not rattle,
dedicated to the delivery of
most fuels .
Dedicated to hydrocarbons,
petroleum products,
d i s t i l l a t e
hydrocarbons,petrol,
kerosene, fuel oil, chips
composite oil, glycol based
coolant transmission,
compatible with most petroleum
products
Norprene Chemical
◆Advantage
◆Corrosion resistance
Double tube, the inner wall is
Teflon material, the outer
layer of neoprene, smooth
surface, free of plasticizers
Resistant to acid and
corrosive organic solvents,
are ideal for pumping acid,
ketones and other corrosive
liquids
Fluran F-5500-A
Norprene A-60-F
Tygon R-3603
------- ----- ----------- ----- ----------- ----- ----
◆Advantage
Platinum vulcanization
treatment, the precipitate
is very low, the hydrophobic
inner surface, its ultra-
smooth lumen can reduce the
accumulation of adsorbent
particles and microorganisms
in the transportation of
sensitive liquid probability
completely non-toxic, non-
hemolytic and pyrogen
ingredients produced.
Tygon 3 35 0
Strong heat resistance
Corrosion resistance
long time
Adsorption of Low
In accordance with America standard
P h a r M e d
◆Advantage
The best choice for tissue
and cell applications, non-
toxic, non-hemolytic, ozone
resistance, anti-oxidation,
ultraviolet and visible
light can not penetrate,
protect sensitive fluid.
Can be repeated autoclaving
does not affect the life of
a closed system can be
disinfected by heat fusion
heat sealing.

11
Hose Parameters
Accessories Optional
FK-1C
Distribution Controller .
can Achieve Rationing.
FO OT SWI TCH:
To co ntrol the pump ’s star t/ stop
Noted: Foot switch and dispensing controller is optional, these
devices control only pump start and stop state operation of the pump
speed and direction through the panel switch settings.
-
-
-
-
-
-
-
Micro flow tube
The basic flow tube
Industrial hose
Tube
Hose section
Wall thickness
Inside diameter
Pressure
Continuous
Interval
Tube
Hose section
Wall thickness
Inside diameter
Pressure
Continuous
Interval
Tube
Hose section
Wall thickness
Inside diameter
Pressure
Continuous
Interval

12
Maintenance And Warranty
Maintenance
Warranty
When the pump is idle, we recommend you to release the tubing from
pressure. This helps to protect the tubing from unnecessary strain
and prolongs its service life Keep rollers clean and dry. This
will prolong the service lives of tubing and pump head
One year product warranty (excluding pump tube), during the
warranty period as a result of user mishandling or man-made
damage, the Company is not responsible for warranty. Of-warranty
repairs, and only pay maintenance cost
Fa u l t D isplay
Trouble shooting
Reason Method
Motherboard insurance
blown fuse
Change It
Drive is broken Change It
Change It
Reinstall the line or
replace a new line .
Open the pump , The fan and display are
normal work,to control the start/stop .
the motor is normal work ,but the pump
head didn’t work .
The pump is normal work .but it’s
not display .
Open the pump, The fan and display are
normal work ,to control the start /stop ,
the pump not work.
The rubber coupler
is broken
The connect line is
Loose or damaged .
---------------------------
---------------------------
--------------------- ------
Operation requirements:
1.The name of the fluid:
2.Flow rates (ml/min):
3.Fluid properties (Corrosion, viscosity,
temperature, etc.):
4.Whether the fluid contains insoluble granules
or suspended solids:
5.The running time for the pump
(hour/day):
6.The pressure of outlet and entry,
suction and delivery lift:
7.Others:
Your contact details:
1.Company name:
2.Address:
3.Contact person:
4.Tel.:
5.Fax:
6.E-mail:
The way you need our reply:
By calling:
By fax:
By E-mail: