Night Stars Ll01-Rgb-R User manual

IMPORTANT SAFEGUARDS
To reduce the risk of re, electric shock, or injury when using any electric
appliance, precautions should be made. These precautions include but are not
limited to:
Read all instructions.
CAUTION! — Use only as directed. Improper use may result in damage to the
eyes due to direct exposure to laser radiation.
This product has a polarized plug to reduce the risk of electric shock. It
will therefore only t into a polarized outlet one way. If the plug does not t,
reverse the plug. If it still does not t, contact a qualied electrician. Do not
use with an extension cord unless the plug can be fully inserted. Do not alter
the plug.
This unit is certied as a Class IIIa laser product by the US Federal Laser
Product Performance Standard (FLPPS) according to regulations in 21 CFR
Subchapter J. Class IIIa laser products can be hazardous when directly
viewed.
Avoid looking directly into Class IIIa lasers. This product, as well as other
demonstration laser products like some laser pointers, are classied as Class
IIIa laser energy levels. This product uses diractive optics to scatter the beam
of energy. This scattering eect causes the energy concentration to drop
below the exposure limits for momentary or accidental viewing at a relatively
short distance for the laser aperture. As with all bright light sources, when you
operate this device in public areas it is recommended that up-close access to
the light be restricted.
While the Class IIIa laser in this device may be hazardous on its own, it is
encased in a protective housing and uses diractive holographic optics,
therefore the laser radiation is not directly exposed to during operation or
maintenance. Each individual laser beam is less than 5mW, which is about the
same as an average laser pointer.
DO NOT attempt to open the protective housing or operate the device if
the aperture windows are damaged. If the unit requires service that involves
removing the protective housing, contact the manufacturer. Opening the
protective housing voids the warranty.
Use only three-wire outdoor extension cords that have three-prong grounding
plugs, plugged into grounded outlets. Acceptable extension cord types:
SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW,
SJW-A, SJOW, SJOW-A, SJTW, SJTW-A, SJTOW, SJTOW-A
Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the
circuit(s) or outlet(s) to be used while operating portable laser light in a wet
location. Receptacles with built-in GFCI protection are available for this purpose.
SAVE THESE INSTRUCTIONS

First, install the included 23A battery in the remote. To
test the remote’s battery connection, press any button
and the LED will illuminate. If the LED does not illuminate,
check to make sure you have installed the battery
according to the correct polarity. The remote can be used
hand-held or mounted to a surface.
Assembly
1. To attach the ground stake, remove the hex screw,
locking washer, and washer from the stake with the
included Allen wrench.
2. Use the same hex screw, locking washer, and washer
to attach the stake to the pivot mount. (See assembly
diagram labeled “2” in the image to the right.)
3. Insert stake into the ground.
4. Position the projection by loosening and tightening the
angle adjustment screws. (Angle adjustment screws
labeled “4” in the image to the right.)
5. Plug the 2-prong adapter into the outlet on the power supply transformer. Screw on the
weather-resistant cap tightly to help protect the connection from weather.
6. With your remote ready and making sure you are within range of the laser, plug in
power supply adapter to power source. Within 5 seconds of plugging in, press the
ON/OFF button on your remote to sync it with the laser. Reposition light if necessary.
Occasionally, re-syncing remote may be necessary after unplugging or after long-term
storage. Repeat steps above if this occurs.
Do not point laser light toward oncoming pedestrians, vehicles, or trafc routes on land, sea, or air.
Ground Stake Allen Wrench Light Projector Remote & Battery
Antenna
When extended, remote has a
range of 8.5 to 11 yards
Remote Control
Flash Setting
Toggle between ashing
or steady light
Change Light Color
Choose red, green, blue or combination
Timer Cancel
Cancels timer settings
6-Hour Timer
Sets the unit on a 6-hour on,
18-hour o daily cycle
8-Hour Timer
Sets the unit on a 8-hour on,
16-hour o daily cycle
2-Hour Timer
Sets the unit on a 2-hour on,
22-hour o daily cycle
4-Hour Timer
Sets the unit on a 4-hour on,
20-hour o daily cycle
2-Prong
Adapter
Light On/O
Press On/O while unit is plugged in and
remote will connect to unit in 5 seconds

Follow Us
Like Us
Viatek Site
Read Instructions
Before Operating MADE IN
CHINA
© 2014 VIATEK CONSUMER PRODUCTS GROUP, INC. All specifications are subject to change without notice. All rights reserved.
For customer service call 888.7.VIATEK (+1.423.402.9010 for outside the United States) or visit us online at viatekproducts.com
Pour le service a la clientele appelez le 888.7.VIATEK (+1.423.402.9010 pour l'extérieur des États-Unis) ou visitez viatekproducts.com
Para servicio al consumidor llame al 888.7.VIATEK (fuera de Estados Unidos marque +1.423.402.9010) o visite viatekproducts.com
Protect your product for 1 year beyond our standard warranty with the Viatek No Question
Protection Extended Warranty Plan. With the Extended Warranty there are no return
shipping charges, the product will be replaced or reimbursed with no deductible, and the
product is protected 100% from any mechanical or electrical failures caused by power
surges or manufacturer’s defects. Order online at viatekproducts.com today.
PATENT PENDING
REV-Model No.
DO NOT DISPOSE OF BATTERIES IN FIRE. ALWAYS DISPOSE OF BATTERIES PER LOCAL & FEDERAL GUIDELINES
Follow Us
Like Us
Viatek Site
06/26/14LL01-RGB-R
Product Specications
Laser Classication
Maximum Laser Power
Laser Wavelength
Laser MTBF
Power Consumption
Power Input
Operation
Operating Temperature
Projection Coverage
Maintenance
Remote Battery
Warranty
Class IIIa
(Single beam) Less than 5mW
Green: 532nm / Red: 660nm
More than 5000 hours
Up to 5 watts
120VAC (when used with supplied transformer)
Indoor / Outdoor
-4˚F to 86˚F
25 ft. x 25 ft.
Maintenance free — no user serviceable parts
23A (L1028), included
Limited 1-year warranty
Notes:
� Only use supplied transformer connected to a properly grounded outdoor
outlet.
� Do not use with dimmers.
� Operate in temperatures of -4˚F to 86˚F. There may be a slight delay if operating
below 55˚F. Please allow up to 10 minutes for light to warm up and reach its full
projection. Green laser startup time may take up to 30 minutes in temperatures
below 14˚F.
� When hanging the laser light, for safety purposes it is recommended to mount
using a sturdy hanging clamp and safety cable.