Nikro APD15150 User manual

INSTRUCTION MANUAL
MODEL #APD15150
& APW15150
COMPRESSED AIR
POWERED HEPA VAC

____
INDUSTRIES, INC.
--------WARNING--------
All Nikro Industries Inc. products that have rated efficiencies of 99.97% @ 0.3 microns and 99.99% @
0.3 microns, have H.E.P.A. filters that have been individually tested to meet these minimum
efficiencies.
Although all the filters have been pre-tested, the possibility of leaks or filter failure due to handling,
transportation, punctures, loaded filters, moisture, wear and tear, etc., does exist.
Therefore, when using this equipment in highly sensitive areas or where any release of particles above
and beyond the minimum efficiencies would be detrimental and harmful to humans, plants or property;
it is strongly recommended that the units be individually tested prior to their use.
This is to assure that they are maintaining the efficiency levels, which they were designed to filter out.
FAILURE TO DO SO COULD RESULT IN SERIOUS HARM TO HUMAN LIFE, PLANT LIFE
AND/OR PROPERTY.
1115 N. Ellsworth Ave., Villa Park, IL 60181
Telephone: [phone] FAX: [phone]
Toll Free: 800-875-6457

AIR OPERATED VACUUM CLEANERS
OPERATION AND MAINTENANCE, MANUAL WITH ILLUSTRATED PARTS LIST
Read and follow all instructions, warnings, and cautions before using this machine.
These instructions are for your protection and convenience. Please read them carefully since
failure to heed these precautions could result in discomfort or injury. When using compressed air
equipment, basic safety precautions should always be followed.
SAFETY INSTRUCTIONS
Air supply should not exceed 100 PSI
Use a compressor and air line that meet the requirements listed below on the specifications chart
Water separator must be used on compressed air line.
Air control valve must be off before connecting to compressed air line, then open valve slowly,
making sure not to exceed the 100 PSI rated pressure.
When cleaner is running, never allow fingers, hair. or loose clothing to come near intake, suction
ports, or nozzle.
Replace damaged or worn parts immediately with genuine original equipment parts to maintain
safety and to protect your limited warranty.
Not recommended for drums with walls and bottoms thinner than 20 gauge.
NEVER LEAVE VACUUM UNATTENDED WHEN CONNECTED TO AIR LINE.
SPECIFICATIONS
Model # Tank Size Tank Construction Static Lift C.F. M. Dry Pickup Wet Pickup Filtration C.F.M. P.S.I Air Hose ID
AHD15150
AHD15225
AHW15150
AHW15225
AHD15150-S
AHD15225-S
AHW1550-S
AHW15225-S
APD15150
APD15225
APW15150
APW15225
AHD55225
AHD55TWN
15 Gal
15 Gal
15 Gal
15 Gal
15 Gal
15 Gal
15 Gal
15 Gal
15 Gal
15 Gal
15 Gal
15 Gal
55 Gal
55 Gal
Painted Steel
Painted Steel
Painted Steel
Painted Steel
Stainless Steel
Stainless Steel
Stainless Steel
Stainless Steel
Polyethylene
Polyethylene
Polyethylene
Polyethylene
Painted Steel
Painted Steel
150”
225”
150”
225”
150”
225”
150”
225”
150”
225”
150”
225”
225”
225”
90
120
90
120
90
120
90
120
90
120
90
120
120
195
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Opt.
Opt.
Yes
Yes
Opt.
Opt.
Yes
Yes
Opt.
Opt.
Yes
Yes
Opt.
Opt.
99.97% at 0.3 micron
99.97% at 0.3 micron
99.97% at 0.3 micron
99.97% at 0.3 micron
99.97% at 0.3 micron
99.97% at 0.3 micron
99.97% at 0.3 micron
99.97% at 0.3 micron
99.97% at 0.3 micron
99.97% at 0.3 micron
99.97% at 0.3 micron
99.97% at 0.3 micron
99.97% at 0.3 micron
99.97% at 0.3 micron
20
100
20
100
20
100
20
100
20
100
20
100
100
200
100
100
100
100
100
100
100
100
100
100
100
100
100
100
1 / 2”
3 / 4”
1 / 2”
3 / 4”
1 / 2”
3 / 4”
1 / 2”
3 / 4”
1 / 2”
3 / 4”
1 / 2”
3 / 4”
1 / 2”
3 / 4”
Compressed Air Requirements

PROCEDURES FOR REMOVING CONTAMINATED FILTERS .
Caution:
When removing contaminated filters or using this machine, you should always wear gloves,
clothing and a respirator approved for the particular contaminant which you are working with.
FILTER REMOVAL PROCEDURES
1. Turn off and unplug machine
2. Slowly and carefully lift one side of the lid assembly from the tank. Holding the lid with
one hand, reach under the lid and gently tap all around the dacron filter bag, allowing any
loose dust particles to drop into the tank.
3. Carefully lift the lid assembly off the tank. With a damp rag, wipe underside of the lid
assembly. Set it aside and dispose of rag properly. (Never set the lid assembly down on the
HEPA filter).
4. Remove the impaction prefilter. (Refer to the following section "Procedure on changing the
impaction filter").
5. Carefully pull the paper filter protector bag over the rim of the tank and push it down into
the tank.
Caution: Be careful not to create any airborne dust by snapping the elastic bag
6. Take the collar of the paper collection bag and carefully slide it down and off the down
tube and remove the collection bag from the tank.
7. Take a damp rag and wipe down the inside of the tank. Dispose of contaminated rag
properly.
8. All hazardous waste must be disposed of properly. Never put contaminated debris in a
regular trash container. All debris must be placed in a bag or container labeled "Hazardous
Materials", and should be removed by a licensed waste hauler.
CONSULT PROPER AUTHORITIES FOR REGULATIONS REGARDING DISPOSAL
PROCEDURE ON CHANGING THE IMPACTION FILTER
1. The precautionary steps described in this manual should be used when changing the
impaction prefilter.
2. The impaction prefilter should be changed when any of the following occur.
A. Whenever a tear is found in any of the filters preceding the impaction filter.
B. At least every other time the collection bag is changed.
3. To change the impaction prefilter, follow the first three procedures in the section on "Filter
Removal Procedures" and then proceed.
4. Carefully slide the non-clinging dacron bag off the HEPA filter and set aside.
5. Remove the impaction prefilter from the HEPA filter. (Never use any type of tool or object
to remove this filter, to insure that you do not puncture the HEPA filter). This filter cannot
be cleaned or reused and should be disposed of properly.

REFERENCE PART NO. DESCRIPTION. 1 860527 AIR LINE CONNECTOR 2 860528 SHUT-OFF VALVE 3 860529 VENTURI BOX 4 860530 VENTURI BOX GASKET 5 860531 BRASS BRUSHING 6 860532 AIR JET, 150 STATIC LIFT 860533 AIR JET, 225 STATIC LIFT 7 860534 VENTURI 8 860535 FOAM INSERT (EXHAUST SILENCER) 9 860536 EXHAUST HOUSING

REFERENCE PART NO. DESCRIPTION QTY. REQ.
1 520008 LID (15 GAL.) 1
2 520018 LID GASKET 1
3 520014 LID EDGING GASKET 1
4 520367 FILTER MOUNTING PLATE 1
5 520307 HEPA FILTER 1
6 520366 FILTER PROTECTOR CAGE 1
7 520316 IMPACTION FILTER - PINK 1

REFERENCE PART NO. DESCRIPTION QTY. REQ.
1 861157 PNEUMATIC HEAD ASSY. 1
2 520210 DACRON FILTER BAG 1
3 520034 FILTER PROTECTOR 1
4 520032 COLLECTION BAG 1
5 860805 TANK AND CART ASSY. 1

#520321-DOWN TUBE ASSY.
INCLUDES
540001 DOWN TUBE ELBOW
860468 DOWN TUBE COUPLER
(RUBBER)
860360 DOWN TUBE 8” LG. X 2” DIA
TUBE
REFERENCE PART NO. DESCRIPTION QTY. REQ.
1 520321 DOWN TUBE ASSY. 1
2 860550 HANDLE 1
3 860802 15 GAL. POLY TANK 1
4 860803 LID LATCH 2
5 520216 INTAKE GASKET 1
6 860549 HOSE INTAKE 1
7 520222 TANK SIDE HANDLE 2
8 860584 AXEL ASSY. 1
9 860801 NYLON INSERT NUT (1/2-13) 2
10 520227 REAR WHEEL 2
11 860804 FRONT CASTER 2
12 520217 INTAKE KNOB 1

ET PICK-UP
CONVERSION LID ASSY.
520037
DACRON FILTER BAG
520034
FILTER PROTECTOR
520315
WATER PICK-UP ADPT.
WARNING: 520317
FOR SAFE AND PROPER WATER PICK-UP, WATER SHUT-OFF
THE CONVERSION ASSY. MUST BE
ASSEMBLED EXACTLY AS SHOWN
IMPORTANT:
WHEN CONVERTING FOR WET PICK-UP,
THE UPPER CLAMP ON THE DOWN
TUBE (LOCATED INSIDE THE TANK
ASSY.) MUST BE SOOSENED AND
BOTTOM HALF OF THE TUBE REMOVED; 15 GAL. TANK ASSY.
THIS WILL PREVENT WATER FROM
SPLASHING UP ONTO THE HEPA FILTER.

WARRANTY
Nikro equipment is warranted for 2 years from the date delivered to the original
purchaser. Parts, which become defective due to faulty workmanship or materials during
normal use in these years will be repaired or exchanged at no charge if returned and
approved by an authorized Nikro service center. The freight shall be at the expense of the
customer.
This warranty does not apply to normal wear and tear, neglect, misuse, or
incorrect installation. If any other replacement parts, filters or attachments are used other
an original Nikro parts, this warranty will become void.
This warranty does not apply to hoses, switches, lights, sensors, or breaks in cords. All
motors are subject to manufacturer’s warranty. Contact Nikro Industries for assistance
with these items.
Nikro disclaims responsibility for loss of production, profits, or any other costs
that may indirectly occur due to the failure of this product.