Ningbo Innopower Hengda Metal Products P1201 User manual

0
GAS FIRE PIT
0063
Model: P1201 is with glass stones
Model: P1201A is with lava rocks and 4pcs logs
Model: P1201A-L is with 4pcs logs
Model: P1201A-LA is with lava rocks
WARNING: FOR OUTDOOR USE ONLY OR IN AMPLY VENTILATED AREAS
PLEASE KEEP THE MANUAL FOR FUTURE REFERENCE!
INSTRUCTION
MANUAL
Pin No.: 0063CU7826

1
GAS FIRE PIT SAFETY WARNINGS
PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION AND USE.
 This appliance must be used outdoors or in a well ventilated area and should not be installed or used indoors.
 To change the gas cylinder in a well ventilated area away from any inflammation sources such as candle,
cigarettes, or other flame producing appliances.
 Do not move this appliance when in operation or after it has been turned off before the temperature has cooled
down.
 Do not attempt to alter the appliance in any manner.
 Do not obstruct the ventilation holes of the cylinder housing.
 Use only the type of gas specified by the manufacturer.
 Repairs should be done by a qualified person.
 In case of violent wind, particular attention must be taken against tilting of the appliance.
 To check that the regulator seal is correctly fitted and able to fulfil its function.
 Do not use this appliance until all connections have been leak tested.
 In the event of gas leakage, the appliance shall not be used or if alight, the gas supply shall be shut off and the
appliance shall be investigated and rectified before it is used again.
 The appliance should be inspected before use and at least annually by a qualified service person. More frequent
cleaning may be required as necessary. It is imperative that control compartment, burners and circulating air
passageways of the appliance be kept clean.
 Shut off and check the appliance immediately if any of the following conditions exist:
 The smell of gas in conjunction with extreme yellow tipping of the burner flames.
 Any guard or other protective device removed for servicing the appliance must be replaced before operating the
appliance.
 Children and adults should be warned of the hazards of high surface temperatures and should stay away to
avoid burns or clothing ignition.
 Young children and pets should be carefully supervised when they are in the area of the appliance.
 Clothing or other flammable materials should not be hung from the appliance, or placed on or near the
appliance.
 Certain material or items when stored under or near this appliance will be subjected to radiant heat and could be
seriously damaged.
 Do not place articles on or against this appliance.
 Do not use or store flammable materials near this appliance.
 Do not spray aerosols in the vicinity of this appliance while it is in operation.
 Always maintain at least 1m clearance from combustible materials.
 Always position the appliance on a firm level surface.
 The cylinder must be stored outdoors or in a well ventilated area.
 Storage this appliance indoors is permissible only if gas cylinder is disconnected and removed from the
appliance.
 The appliance must be installed and gas cylinder stored in accordance with local gas fitting regulations.
 The hose assembly must be replaced prior to the appliance being put into operation if there is evidence of
excessive abrasion or wear, or if the hose is damaged, and that the replacement hose assembly shall be that
specified by the manufacturer.
 Shut off the valve at the gas cylinder or the regulator before moving the appliance.
 To close the gas supply at the valve of the gas cylinder or the regulator after use.
 Checking the tubing or the flexible hose per month and each time the cylinder is changed.
 The regulator & hose assembly must be located out of pathways where people may trip over it or in area where
the hose will not be subject to accidental damage.
 Flexibles metallic hoses which are parts of the gas circuit shall comply with EN16617:2015.

2
PART LIST
ASSEMBLY
Instruction before assembly
Required Tools: Philip Screwdriver / Adjustable Spanners / Wrenches
Leak Detection Solution: one part, detergent and three parts water
Tighten all connections after completion of assembly.
Before assembly, make sure all packing material and any transmit protection must be moved.
Small deviations in equipment may occur. This is no lack of quality but subject to improvements.
# DESCRIPTION
1 Reflector
2 Short bolt
3 Long bolt
4-1 Top insulation board
4-2 Glass window bracket A
4-3 Glass window
4-4 Glass window bracket B
5 Burner & tank housing
assembly
6 M5x12 Screw
7 M5x6 Screw
8 Lava rock or glass stones
9 4pcs Logs or without
CAUTION:
 Glass window is a hot part, don’t touch it while it is working!
 In case of hotplate glass breakage, shut off all burners and any
heating element and isolate the appliance from the power supply.
 Do not touch the appliance surface.
 Do not use the appliance before leakage test.

3
Step 1: Open door and take out all inside parts.
Step 2:
Install the 4pcs Glass window bracket B (#4-4) onto the Burner & tank housing assembly (#5) by using 4pcs M5x12
screws (#6), the bigger screw-hole side on the bottom of bracket B must be subjacent.See illustration 1
Note: The right-angle of bracket B and tank housing assembly must be paralleled during installing
Step 3 : Install the 4pcs lower Glass window bracket A (# 4-2) onto the Glass window bracket B (# 4-4) by using
16pcs M5x6 screws (#7). See illustration 1
Step 4: Insert the Glass window (#4-3) into the lower Glass
window bracket A (# 4-2) carefully, then fix the upper Glass window bracket A (# 4-2) onto the Glass window bracket
B (# 4-4) by using 16pcs M5x6 screws (#7) carefully. See illustration 2
Step 5: A-Put all lava rocks or glass stones (#8) and 4pcs logs (#9 or without) on the burner.
B- Fix 4pcs long bolts(#3), top insulation board (#4-1), 4pcs short bolts (#2) and reflector (#1) according to the
following order
Please remove out all glass
parts slowly and carefully.
illustration 1
illustration 2

4
CAUTION:
 Glass window is a hot part, don’t touch it while it is working!
 In case of hotplate glass breakage, shut off all burners and any
heating element and isolate the appliance from the power supply.
 Do not touch the appliance surface.
 Do not use the appliance before leakage test!
 Do not block pilot box and burner when filling lava rock or glass stones on the burner.
GAS REQUIREMENTS
 The pressure adjuster should comply with the standard EN16129 and current regulations in the country where it
is installed, which may be found at your nearest retailer of gas items.
 Refer to the technical date. It is strictly prohibited to use adjustable pressure.
 The life expectancy of the regulator is estimated as 10 years. It is recommended that the regulator is changed
within 10 years of the date of manufacture or the national conditions require it.
 The type of replaceable hose should meet the standard of EN16436-1.
 The length of the hose must be 0.4 meters (minimum) and 1.0 meters (maximum). Worn or damaged hose must
be replaced. Ensure that the hose is not obstructed nor kinked. It is recommended that the hose is changed
within 1 year of the date of manufacture or the national conditions require it.
 Never use a gas cylinder with a damaged body, valve, collar, or foot ring. A dented or rusty gas tank may be
hazardous and should be checked out by a gas supplier.
 Always perform a leak test on gas connections whenever a cylinder is connected. If bubbles form in the leak test
solution, do not use. Never use a flame to test for leaks.
 Never connect this appliance to an unregulated gas source.
 Use only regulator and hose approved for LP Gas at the correct pressures and gas type.
 Using 30mbar butane regulator for butane of I3B/P(30) or butane of I3+.
 Using 30mbar propane regulator for propane or butane/propane mixture of I3B/P(30).
 Using 37mbar propane regulator for propane of I3P(37).
 Using 50mbar butane regulator for butane of I3B/P (50).
 Using 50mbar propane regulator for propane or butane/propane mixture of I3B/P (50)
CONNECTING TO A GAS CYLINDER
 Use max.13kg gas cylinder. Please refer to your gas supplier for suitable gas cylinder.
 Refer to your gas supplier for instructions on the use of your gas cylinder.
 Only change gas cylinders outdoors or in a well ventilated area away from naked
flames and any other source of ignition.
 The gas cylinder must always be used in an upright position.
 Close the appliance control knob by turning fully clockwise.
 Close the gas cylinder tap and then attach the regulator onto the gas cylinder.

5
 Tighten all connections firmly and with a spanner where appropriate. The cylinder should be located on the
cylinder base.
 Check for leaks at all joints using soapy water. If a leak is found, tighten the joint and then re-test.
SECURING A GAS CYLINDER
1. Position a gas cylinder inside the tank housing.
2. Stick cylinder restraint straps together as RIGHT photo illustrated.
The straps must be in a proper tightness for the gas cylinder.
Caution: Please take care that the cylinder restraint straps. DO NOT strain the regulator assembly.
LEAK TESTING
NEVER USE A NAKED FLAME TO CHECK FOR LEAKS.
NEVER LEAK TEST WHILE SMOKING.
The gas connections on this appliance are leak tested at the factory prior to shipment.
This appliance needs to be periodically checked for leaks and an immediate check is
required if the smell of gas is detected.
 Make a soap solution using 1 part of liquid dish-washing soap to 3 parts water. The
soap solution can be applied with a soap bottle, brush, or rag to the leak tested
points shown in the figure.
 The valve of the gas cylinder should be in the OFF position at this point of the leak
test. Once the soapy solution is applied to the gas connections, the valve of the gas
cylinder needs to be turned to the ON position.
 Soap bubbles will begin to form in the soapy solution if a leak is present.
 In case of a leak, turn off the gas supply. Tighten any leaking fittings, then turn the
gas supply on and recheck.
OPERATING INSTRUCTIONS
BEFORE FIRST USE AND AFTER EVERY GAS CYLINDER CHANGE, GAS DELIVERY SYSTEM MUST BE
PURGED OF AIR BEFORE IGNITING! TO DO THIS, TURN THE CONTROL KNOB ANTI-CLOCKWISE TO THE
PILOT SETTING. PRESS KNOB IN AND HOLD FOR ABOUT 2 MINUTES BEFORE ATTEMPTING IGNITION.
BATTERY REPLACMENT
Remove impulse ignition cap from below Ignition by turning cap counterclockwise. Install 1 AAA battery.
Negative end of battery goes in first, then replace impulse ignition cap by turning cap clockwise.
TO LIGHT THE PILOT
 Check all connections prior to each use.
 Turn on main gas supply at source.
 Press to turn control knob anti-clockwise to PILOT.
 Hold knob depressed, press IGNITION button
repeatedly until pilot flame is lit, then continue to hold
the knob depressed for 20 seconds until the pilot
remains it after releasing knob.
 If pilot fails to ignite or alight, press to turn knob
clockwise to OFF and repeat.

6
TO LIGHT THE APPLIANCE
 The pilot should be lit and the knob set to PILOT.
 Hold knob depressed gently and turn anti-clockwise to HIGH.
 When the appliance glows lit, turn knob clockwise from HIGH to LOW as needed.
RE-LIGHTING
 Turn Control Knob to OFF.
 Wait at least 5 minutes to let gas dissipate, before attempting to re-light pilot.
 Repeat the “Lighting” steps.
TO EXTINGUISH
 Hold knob depressed & turn the knob clockwise to 'OFF'
 Close the valve of the gas cylinder or the regulator after use.
 Close the gas bottle and allow this appliance to cool before moving the appliance.
Note: Close regulator after use, allow the appliance to cool before moving.
Note: When the appliance is not in use, turn the gas cylinder OFF.
IMPORTANT SAFETY RULES
For use outdoors or in amply ventilated areas.
An amply ventilated area must have a minimum of 25% of the surface
area open.
The surface area is the sum of the walls surface.
The use of this appliance in enclosed areas can be dangerous and is
PROHIBITED.
Children and adults should be aware of the high operating
temperatures of areas above the post when operating this appliance.
Children should be carefully supervised when in the vicinity of the
appliance.
NEVER hang anything, including clothes or any other flammable items,
on this appliance.
DO NOT operate this appliance unless it is fully assembled with its
reflector in place.
Respect the minimum clearances from combustible materials.
MAINTENANCE
To enjoy years of outstanding performance from your appliance, make sure you perform the following maintenance
activities on a regular basis:
 Keep exterior surfaces clean.
 Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents.
 While washing your unit, be sure to keep the area around the burner and pilot assembly dry at all times. If the
gas control is exposed to water in any way, DO NOT try to use it. It must be replaced.
 Airflow must be unobstructed. Keep controls, burner and circulation air passageways clean. Signs of possible
blockage include:
1m
1m
Ceiling/Overhang
Wall

7
 Gas odor with extreme yellow tipping of flame.
 The appliance does NOT reach the desired temperature.
 The appliance glow is excessively uneven.
 The appliance makes popping noises.
 Spiders and insects can nest in burner or orifices. This dangerous condition can damage the appliance and
render it unsafe for use. Clean burner holes by using a heavy duty pipe cleaner. Compressed air may help clear
away smaller particles.
 Carbon deposits may create a fire hazard. If any carbon deposits develop, clean dome and engine with warm
soapy water.
Note: in a salt-air environment (such as near the sea), corrosion occurs more quickly than normal.
Frequently check the corroded areas and repair them promptly.
SERVICING
 Please consult your local dealer for servicing this appliance and replacement of its parts. The servicing of the
appliance shall be carried out only by authorised personnel.
 Caution: do not use unauthorized parts or components for this appliance, only use original equipment
replacement parts and components. The use of unauthorized parts or components will void the warranty and
can create an unsafe condition.
STORAGE
There is no limitation on the storage of the appliance indoors provided that the cylinder is removed from the
appliance.
Between uses:
 Turn control knob OFF
 Turn gas cylinder OFF
Store the appliance upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail,
snow, dust and debris).
If desired, cover to protect exterior surfaces and to prevent build up in air passages.
Note: Wait until the appliance is cool before covering.
During periods of extended inactivity or when transporting:
 Turn control knob OFF.
 Disconnect gas cylinder and move to a secure, well ventilated location outdoors. DO NOT store in a location that
will exceed 50°C.
Store the appliance upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail,
snow, dust and debris).
If desired, cover the appliance to protect exterior surfaces and to prevent build up in air passages.
Note: Wait until the appliance is cool before covering
TROUBLESHOOTING
IF THE PROBLEM IS: AND THIS CONDITION EXISTS: THEN DO THIS:
Pilot won’t light
Cylinder valve is closed Open valve
Blockage in orifice or pilot tube Clean or replace orifice or pilot tube
Air in the gas line
Open gas line and bleed it (pressing
control knob in) for not more than
1-2 minutes or until you smell gas
Low gas pressure Gas cylinder low or empty
Igniter fails Use match to light pilot, and obtain new
igniter and replace.
Pilot won’t stay lit Dirt build up around pilot Clean dirt from around pilot

8
Connection between gas valve and pilot
assembly is loose Tighten connection and perform leak test
Bad thermocouple Replace thermocouple
Burner won’t light
Gas pressure is low Replace gas cylinder
Blockage in orifice Clear blockage
Control knob is not in "ON" position Turn control knob to "ON" position
Burner flame is low
Note: Do not operate the
appliance below 5 ℃
(40°F)
Gas pressure is low Replace gas cylinder
Outdoor temperature is below 5℃(40°F)
and tank is less than 25% full Replace gas cylinder
Supply hose is bent or kinked Straighten hose and perform leak test on
hose
Control knob is fully " ON"
Turn control knob to "OFF", let it cool to
room temperature and check burner and
orifices for blockage
Emitter glows uneven
Note: Bottom 2.5cm of
emitter normally does
not normally glow
Gas pressure is low Replace gas cylinder
Base is not on a level surface Place the appliance on a level surface
The appliance is not level Level the appliance
Carbon build-up Dirt or film on reflector and emitter Clean reflector and emitter
Thick black smoke Blockage in burner
Turn control knob to "OFF", let it cool to
room temperature and remove
blockage and clean burner inside and
outside.
IN THE EVENT OF ANY PROBLEM, PLEASE ALWAYS CONSULT YOUR LOCAL DEALER
TECHNICAL DATA
Product Name: Gas fire pit
Model No.: P1201, P1201A, P1201A-L, P1201A-LA
Country
Code
BE-CY-CH-CZ-FR-
ES-GB-GR-IE-IT-PT
-SK-SI-TR
PL
BG-HR-CH-CY-DK-EE-FI-
GR-HU-IT-IS-LT-LV-MT-NL-
NO-PT-SE-SI-SK-RO-TR
AT-CH-DE
Category  I3+(28-30/37)  I3P(37)  I3B/P(30)  I3B/P(50)
Gas G30 G31 G31 G30/G31 G30/G31
Gas type Butane Propane Propane Butane/Propane Butane/Propane
Pressure(mbar) 28-30 37 37 30 50
Heat input 8kW 8kW 8kW 8kW 7.5kW
Consumption 599g/h 576g/h 576g/h 599g/h 531g/h
Gas injector 1.4mm 1.4mm 1.4mm 1.4mm 1.15mm