Outdoor GreatRoom Company Havenwood HVGW-1224 User manual

1 | P a g e
Havenwood Fire Pit
Installation Instructions for
HVGW-1224 and HVDG-1224

2 | P a g e
Contents
Package Contents and Required Tools………3
Placing and assembling the Table………..…...4
Igniter Installation……………………….………..….5
Gas Connections…………….………………………...6
Thermocouple Installation………………………..7
Electrode Installation…………………………....…7
Locating Propane tank………..……………………8
Finishing Touches……………………………….……9
42513 REV C 12.10.21

3 | P a g e
Required Tools
2 Open Ended Wrenches
To make gas connections
Leather Gloves
To protect hands from rough edges found
on the coffee table.
One (1) AAA Battery (not included)
Required for piezoelectric igniter
installation.
Electric Screw Gun with Philips tip
(Used for attaching brackets to top and top
to frame.)
Included in packaging

4 | P a g e
Placing and Assembling the Fire Pit Table
(Everblend Top)
1. Remove all components from packaging.
2. Move the base (remove door) to desired location and set into
place.
3. When locating your table, refer to the manual included with your
burner and maintain clearance to combustibles.
4. Assemble the 2 brackets in the Everblend top using the 4X
provided ¼-20 Philips head screws.
5. With the help of another person, carefully set the Everblend top
into place on the base and center it. Using the 4 sheetmetal screws
provided, secure the Everblend top to the base.
6. Set burner into place. See the section labeled Gas Connection and
Igniter Installation to install gas lines and piezoelectric igniter.

5 | P a g e
Igniter Installation
•Locate CF-SPARKER inside of crystal fire
burner box.
•Remove CF-SPARKER cap and hex nut. Insert
AAA battery (not included) with + end out.
•Install CF-SPARKER into control panel as
shown below.
•Depress CF-SPARKER button to test your
sparker.
Located and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.

6 | P a g e
Gas Connections
Read and understand your Crystal Fire® Plus owner’s manual
before beginning burner hookups or using the device.
See Crystal Fire® Plus instruction manual for burner installation.
•All gas connections were completed at the factory.
Check all connections for leaks. If needed, tighten connection
with 2 wrenches and re-check for leaks.
Attach burner valve to control panel with provided screws as
shown below. Ensure sparker box is installed before this step

7 | P a g e
Thermocouple Installation
Electrode Installation
•Refer to Crystal Fire® Plus instruction manual for
detailed attachment of thermocouple.
•Attach thermocouple to burner valve as shown below.
•Connect igniter and ground wire to sparker box. Both
wires can connect to either connection point. The unit
will operate in either configuration.
•Test system by pushing the button on the igniter.
Consult the troubleshooting section of the Crystal Fire®
Plus Burner Owner’s Manual, if the spark is weak,
intermittent, or not present.

8 | P a g e
Locating your Tank
•Your tank should be positioned so that
the fuel can be shut off after each use.
•Slide the tank into the framework past
the line shown below. This is to allow
the door to close completely.
•Confirm all hoses are clear and not
touching the burner.
Position tank behind this line
Install door by setting the bottom on the catching hooks first and
then closing. Magnets in the table will hold door closed.

9 | P a g e
Finishing touches
Once fire pit is set up and in the desired position,
scatter decorative glass on burner surface forming
an even layer of beads.
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITHOUT INCLUDED GLASS
BEADS OR OTHER APPROVED FIRE MEDIA
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITH BURNER COVER IN PLACE

10 | P a g e
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to hooking up your
linear burner, including safety information, proper tightening of
connections with two wrenches and full burner setup and lighting
instructions.
DO NOT ATTEMPT TO INSTALL CFP1224 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE® PLUS MANUAL. IF YOU ARE
UNSURE OF HOW TO COMPLETE THE STEPS OUTLINED, CONSULT A
QUALIFIED TECHNICIAN
WARNING
After consulting the manual and following instructions, remember; before operating,
all gas connections must be fully checked for leaks