Outdoor GreatRoom Company Renegade Fire Table RNG-32 User manual

1
Renegade Fire Table
Installation Instructions for RNG-32

2

3
Contents
Required Tools…………………………….…..2
Included with your Fire Pit……………….3
Assembly Instructions………………….………4
Gas Connections………………………….…….6
Igniter Installation…………….……………...8
Position Your Tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
One AAA Battery (not included)
Required for electric spark igniter installation
Phillips Screwdriver
To attach mounting screws to control panel
Contents
Required Tools………………………………….........3
Included with your Fire Pit………………………..4
Assembly Instructions……………………………….5
Gas Connections……………………………………….7
CF-SPARKER Installation…………………….….….9
Install Fire Media…………………………………….10
Position Your Tank…………………………………..11
Storage…………………………………………………...12
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
REV A 12-19-17

4
Included with your Fire Pit
TOUCH
UP
PAINT
Gas Valve [1X]
Mounting
screws [2X]
Control knob
[1X]
NF-16-RD Burner [1X]
Burner Cover [1X]
Part #: RNG-4
Media Retention Pad [1X]
Part #: RNG-PAD
Leg [3X]
Part #: RNG-2
Base [1X]
Carrying Bag [1X]
Part #: CB-REN
Gas Valve Kit
GM-KV

5
Included with your Fire Pit
A. 4 Fasteners
B. 4 B-Bolts
C. 4 C-Bolts
D. 4 Bolt Caps
E. Touch-Up Paint Bottle
Assembly Instructions
55
Assembly Instructions
NOTE: Before assembly, check for damage. Do not use damaged components.
1. Unpack all the contents from the box and remove the individual
packaging from each component.
2. Carefully lay the Base, with underside facing upwards. Check to make
sure that clasps are in the open position.
3. Insert the Legs into the openings attached to the Base. Listen
for a click. This ensures that the securement pin on the Legs
is in place. Repeat this process for each Leg.
Securement Pin

6
4. Once all Legs are securely attached to Base, move the
clasps to the closed position.
5. Flip table into the upright position.
*NOTE*: Clasp arm can be rotated to adjust for tightness

7
1. Attach natural gas supply line using a 3/8” flare fitting, or
attach the included black rubber propane hose and regulator to
the bottom fitting of the control valve.
TIGHTEN SECURELY WITH A WRENCH
2. Lay the burner upside down on a flat, soft surface to avoid
scratching the polished metal. Ensure the correct orifice is
installed for the fuel type you are using (see Crystal Fire user
manual included with burner for orifice sizing information).
Attach the included metal flex hose to the burner.
TIGHTEN SECURELY WITH TWO WRENCHES
Gas Connections
Read and understand your Crystal Fire owner’s manual before
beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
Propane
input
Natural
gas input
or
Natural gas supply line
as specified by local
building codes

8
Metal flex line to
burner
ONLY
TIGHTEN CONNECTION
SECURELY WITH WRENCH
3. Attach flex line from the burner to gas valve as
shown below.
WARNING
Check all connections before each use when traveling with the table. This is to
ensure no component has become lose during traveling or relocating the table.

9
CF-SPARKER Installation
CF-SPARKER will not operate correctly without an ignition and ground
wire attached.
Plug both BLACK wires hanging from the burner into the back of
the sparker box.
Before turning on gas, test CF-SPARKER by pushing the button
on the igniter. Consult the troubleshooting section of the
Crystal Fire Owner’s Manual if the spark is weak, intermittent,
or not present.
1. Make sure the valve is in the OFF
position before beginning.
2. Install CF-SPARKER as shown, using
a AAA battery (not included).
Negative end should be placed
inside the CF-SPARKER, positive
end outside of the CF-SPARKER.
OFF

10
Install Fire Media
1. Scatter all of the included Glass Beads evenly onto burner
surface.
• DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT GLASS
BEADS OR OTHER DECORATIVE MEDIA PRESENT
• DO NOT OPERATE CRYSTAL FIRE BURNER WITH BURNER
COVER OR FOAM PAD IN PLACE
*NOTE*: Glass beads can be left in place within the
table for quicker set up for the next usage. See page 12
for storage information.

11
After installing CF-SPARKER and making gas connections,
verify that all connections are tight and that no leaks are
present using a solution of soapy water or a commercially
available leak-check solution.
Position Your Tank
(If Applicable)
1. Connect the propane hose/regulator to the propane tank and
hand tighten (DO NOT USE A WRENCH)
2. With the tank under the table, ensure that no hoses, wires, or
any other components are kinked or touching the burner pan.
WARNING
Locate the hose out of walk ways and inspect the hose for damages before each use.

12
Storage
Your Renegade Fire Table can safely be stored in its included carrying
bag so it is ready to be quickly set up for the next use.
2. Insert Media Retention Pad into burner opening (media can be
left in place).
*NOTE*: Allow 30 minutes for table to cool before inserting
Media Retention Pad into table.
1. Ensure that control panel is in the off position and
that the table is disconnected from the gas supply.
Disconnect from gas supply
and remove tank.

13
4. Close all top latches to secure Burner Cover in
place.
3. Position Burner Cover over top of Media Retention Pad
so that all cover latches line up with latches on table

14
5. Collapse and remove all Legs from base latches.
Legs can be stored within cavity of Base as shown above.
Store legs within Base cavity.
6. Place entire table assembly into Carrying Bag for easy storage.
*REMINDER*: Wait 30 mins before beginning the storage process.

15
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks
Warranty: Fire pit tables are covered under a 1-year
manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form/ to
register your product.

16
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]