Ningbo SS6058H User manual

ABNORMITY AND COUTERMEASURE IN USE
Index
Abnormities
Cause
Countermeasure
1
After finishing the
normal shredding, it
runs ceaselessly yet.
Too much scrapped
paper in the
wastebasket, so that
the just scrapped
paper cannot fall
and leave in the
entry.
1.Cut off the power, and
empty the
wastebasket.
2.Cut off the power, and
press the scrapped
paper down to make
them away from the
machine head.
2
Paper feed or positive
rotation is normal, but
there are still some
scrapped paper
hanging at the exit
after finishing.
The slots of the
blades clamp the
scrapped paper.
Set the slide switch to
“REV” (if need, please
clean the scrapped
paper at the exit).
3
It can’t work if feeding
paper follows
withdrawing paper.
Some scrapped
paper lock
automatic inductive
device.
Set the slide switch to
“REV”.
4
Some paper is in the
entry, but shredder
does not work.
After feeding paper,
any corner of the
paper is inserted,
but the rest doesn’t
touch automatic
inductive device.
Adapt to the position of
the feeding paper and
make it touch the
automatic inductive
device.
5
The paper is jammed,
and the machine stops
rotating.
1. The number of
the inserted
paper is too
larger than the
limitation
2. Locked rotor
makes the motor
overheated and
then temperature
protection set
takes action.
1.Set the slide switch to
“REV” and withdraw
the shredding paper.
2.Unplug the plug and
let the machine stop
for a while.
6
The machine doesn’t
start after inserting a
sheet of paper, or stop
running when paper is
being inserted.
The paper is too
thin, too soft, humid,
or too crinkly to
activate automatic
inductive device.
1.Fold the paper and
then insert it.
2.Set the slide switch to
“REV”.
Disposal instructions
This recycling logo informs the final user that it’s forbidden to
put your product on garbage. If they don’t want this product
anymore they should return it to the distributor.
Manufacturer: Ningbo Ofitech Business Machines Co., Ltd
Address: Kaifat Group, Qiming Road, Yinzhou Industrial Zone,
Ningbo 315105, P.R. China

PAPER SHREDDER
SS6058H
USER MANUAL

SPECIFICATIONS
Model No: SS6058H
Cutting Style: Strip cut
Entry Width: 220mm
Shred Capacity: 5 sheets (A4 paper)
Input: AC 230V, 50Hz, 0.9A
Operating cycle:2 min on / 40 min off
Net weight: 1.2kg
NAMES OF COMPONETS
1. 3-Position slide switch for AUTO, OFF and REV.
2. Paper entry:
Put paper into this entry to shred.
3. Handle
SAFETY SYMBOLS
Warning: Please pay more attention to the safety instruction , before
operate the machine otherwise wrong operation will result in danage to
users.
Product is not intended for
use by children (product is
not a toy)
Avoid hair touching the
document feed opening.
Avoid touching the
document feed opening
with hands.
Do not insert paper clips or
staples into the infeed slot.
Avoid clothing and long
necklaces or bracelets
touching the document feed
opening
Keep aerosol products away (for
products incorporating a
universal (brush ) motor.

INSTALL GUIDE
1. Put the machine on flat table.
2. Insert the power plug into the corresponding electric socket and make sure
that the working voltage complies with the supplying voltage.
OPERATION GUIDE AND REMARKS
1. Set the slide switch to “AUTO”position, at the same time, the machine is on
standby; put the shredding paper, vertically into the entry, there after, it starts
up automatically and does shredding; it returns to standby automatically
after finishing.
2. When jam caused by inserting too much paper, or you want to withdraw the
paper immediately at the normal shredding, please set the slide switch
to ”REV”, at the same time, the machine does the reverse rotation and
returns the paper that has not been shredded; then put the switch to “OFF”.
3. To ensure your machine has a long use life and exerts good shredding
function, please notice the maximum number of shred paper. For continuous
paper shredding in large quantity, please minimize the consecutive using
time to 2 minutes. Hence, you can properly protect your shredder for higher
efficiency.
4. If the machine works continuously or spasmodically for a long time, it may
pause because the inside temperature increases continuously. After resting
for a period of time, it can work again.
5. Please do not put clips, adhesive paper, adhesive tapes or cloth into the
paper entry in order to avoid damaging the blades or lowering the shredding
performance.
6. If you want to clean the wastebasket or the machine, or the machine is not
used for a long time, please cut off the electric power and unplug the
machine.
SAFETY OPERATION GUIDE
1. Before use, please read introduction manual carefully;
2. Keep ties, jewelry, hair, etc. away from the machine to insure personal safety;
3. Do not place the machine near the heat sources or in the humid environment
for a long time;
4. Please use the machine near the electric socket to unplug easily;
5. When clean the machine or repair the damaged plug, please unplug it from
the electric socket at first;
6. Machine must be far away from children and pets;
7. If the machine is not to be used for a long time, please cut off the electric
power and unplug.