Nortek Control SpeakerCraft HRSi User manual

SpeakerCraft HRSi / XTEQi
HRSi-8 /HRSi-10 /HRSi-12 /XTEQi-12
INSTALLATION GUIDE
HRSi XTEQi

SpeakerCraft HRSi / XTEQi 2
Table of Contents
FCC Notice.......................................................................2
Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Unpacking ................................................................4
Care .....................................................................4
Amplier Panel Features......................................................4
Subwoofer Placement .......................................................7
Connecting your Subwoofer (LFE) ..............................................8
Connecting your Subwoofer (Stereo) ............................................9
Conguring your Subwoofer ..................................................10
Subwoofer Discovery ...............................................................10
Volume ..........................................................................10
Crossover ........................................................................11
Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Delay............................................................................12
Manual EQ .......................................................................12
Using Auto EQ ....................................................................13
Settings .........................................................................13
Specications..............................................................14
HRSi-8 ..........................................................................14
HRSi-10 .........................................................................14
HRSi-12 .........................................................................14
XTEQi-12 ........................................................................14
Limited 2-Year Warranty......................................................15
2-Year Warranty ...................................................................15
Attention: To Our Valued Customers ............................................16
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution - changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Canada
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
FCC and IC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the exemption from the routine
evaluation limits in section 2.5 of RSS 102.
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 20 centimeters from user and bystanders.
Warning: The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102, and users can obtain Canadian information
on RF exposure and compliance from the Canadian Representative Product Solutions Group at Tel: [phone].

Nortek Security & Control LLC
3
Important Safety InformatIon
renSeIgnementS de SécurIté ImportantS
1. Read these instructions
2. Keep these instructions
3. Heed all warnings
4. Follow all instructions
5. Do not use this apparatus near water
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two
blades with one wider than the other. A grounding plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not
t into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience
receptacles, and at the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold
with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. No naked ame sources, such as lighted candles, should be placed on the apparatus
16. WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and
objects lled with liquids, such as vases, shall not be placed on apparatus.
17. WARNING: The mains plug/appliance coupler is used as disconnect device, the disconnect device shall remain readily operable.
18. WARNING: An apparatus with Class I construction (a three wire AC Mains cord) shall be connected to a mains socket outlet with a protective earthing
connection.
19. Correct disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased.
They can take this product for environmentally safe recycling.
1. Lisez ces instructions
2. Conservez-les
3. Tenez compte de tous les avertissements
4. Suivez toutes ces instructions
5. N’utilisez pas cet appareil près de l’eau
6. Nettoyez-le uniquement avec un chiffon sec.
7. Ne bloquez aucune fente de ventilation. Installez conformément aux instructions du fabricant.
8. Ne l’installez pas à proximité de sources de chaleur comme des radiateurs, des bouches de
chauffage, des cuisinières ou de tout autre appareil (y compris les amplicateurs) produisant de la
chaleur.
9. N’éliminez pas la fonction de sécurité de la che polarisée ou de mise à la terre. Une che polarisée
possède deux lames, dont l’une est plus large que l’autre. Une che de mise à la terre possède deux
lames et une troisième broche pour la mise à la terre. La broche large ou la troisième broche est
fournie pour votre sécurité. Si la che fournie ne rentre pas dans votre prise, consultez un électricien
pour remplacer la prise obsolète.
10. Sécurisez le cordon d’alimentation an d’éviter qu’on lui marche dessus ou qu’il soit pincé, en
particulier au niveau des ches, des prises de courant et au point de sortie de l’appareil.
11. Utilisez uniquement les xations/accessoires spéciés par le fabricant.
12. Utilisez uniquement avec le chariot, le support, le trépied, le support ou la table spéciés par le fabricant ou vendus avec l’appareil. Lorsqu’un chariot ou un support est
utilisé, faites preuve de prudence lorsque vous déplacez la combinaison chariot/appareil pour éviter les blessures dues au basculement.
13. Débranchez cet appareil pendant les orages ou lorsqu’il n’est pas utilisé pendant de longues périodes.
14. Conez les réparations à des réparateurs qualiés. La réparation est nécessaire lorsque l’appareil a été endommagé de quelque manière que ce soit, par exemple
lorsque le cordon du bloc d’alimentation ou la che est endommagé, lorsqu’un liquide a été renversé ou que des objets sont tombés dans l’appareil, lorsque l’appareil a
été exposé à la pluie ou à l’humidité, lorsqu’il ne fonctionne pas normalement ou lorsqu’il est tombé.
15. Aucune source de amme nue, comme des bougies allumées, ne doit être placée sur l’appareil
16. AVERTISSEMENT : Pour réduire les risques d’incendie ou de choc électrique, n’exposez pas cet appareil à la pluie ni à l’humidité. L’appareil ne doit pas être exposé à
des gouttes ou des éclaboussures et des objets remplis de liquide, comme des vases, ne doivent pas être placés sur l’appareil.
17. AVERTISSEMENT : La che secteur / le prolongateur utilisé comme dispositif de débranchement doit rester facilement accessible.
18. AVERTISSEMENT : Un appareil avec un câble de classe I (un cordon d’alimentation secteur CA à trois ls) doit être connecté à une prise de courant
avec une mise à la terre de protection.
19. Mise au rebut correcte de ce produit. Cette étiquette indique que ce produit ne doit pas être éliminé avec d’autres déchets ménagers dans tous les
pays de l’UE. An de prévenir d’éventuels dommages à l’environnement ou à la santé humaine résultant d’une élimination incontrôlée des déchets,
recyclez-les de manière responsable pour promouvoir la réutilisation durable des ressources matérielles. Pour retourner votre appareil usagé, veuillez
utiliser les systèmes de retour et de collecte ou contactez le revendeur auprès duquel le produit a été acheté. Ils peuvent prendre ce produit pour un
recyclage écologique.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning ash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure, that may be insufcient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user of the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
MISE EN GARDE
RISQUE DE CHOC ÉLECTRIQUE
NE PAS OUVRIR
ATTENTION : POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE, NE
RETIREZ PAS LE COUVERCLE (OU L’ARRIÈRE)
AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR À L’INTÉRIEUR
CONFIEZ LES RÉPARATIONS À DES RÉPARATEURS QUALIFIÉS
Le triangle équilatéral contenant un éclair terminé par
une èche est destiné à alerter l’utilisateur de la
présence d’une « tension dangereuse » non isolée
dans le boîtier du produit et dont l’ampleur peut être
sufsante pour constituer un risque de choc électrique
pour les personnes.
Le point d’exclamation dans un triangle équilatéral est
destiné à alerter l’utilisateur de la présence d’instructions
importantes de fonctionnement et d’entretien dans la
documentation accompagnant l’appareil.

SpeakerCraft HRSi / XTEQi 4
unpackIng
Your subwoofer should reach you in perfect condition. If you notice any
shipping damage, please contact your Dealer immediately.
Gently lift the unit out, and remove all the packing material. It's important to
save all the packing materials and the box in case your subwoofer ever needs
to be moved or returned.
care
To maintain the speaker cabinet’s nish, rst unplug the power cord and then
use a soft cloth to clean the surfaces. If your subwoofer needs servicing,
please read the Warranty section, page 14. If a problem persists, contact your
nearest authorized Dealer.
amplIfIer panel featureS
ON
OFF
STATUS
LOW LEVEL OPTIONAL WIRELESS RECEIVER POWER
100-120V~ 220-240V~
FUSE T8AL/250V
100-120V~60Hz 6A
220-240V~50Hz 3A
USB POWER
5V 500mA
IN
OUT
L/LFE
R
HRSi
➍ ➎
➐
➑
➒
➊
➋
➌
➏

Nortek Security & Control LLC
5
1. Power Indicator. This light is illuminated blue when the subwoofer is turned on and
playing. It illuminates red when the subwoofer is in on, but in Standby mode.
2. Low-Level Inputs. These connect with RCA type cables from the line-level outputs of
your receiver or preamp. Here are two examples: If your processor or receiver has a
single subwoofer output, connect it to the subwoofer’s LFE input connector (see page 8).
If your processor or receiver has stereo line-level output, connect it to the subwoofer’s
red and white Low Level “IN” connectors.
3. Low-Level Outputs. These connect with RCA type cables to daisy-chain additional
subwoofers or powered speakers. These outputs are pass-thru, meaning they will pass
through the same audio signal that is fed into the Low-Level inputs to the Low-Level
outputs.
4. USB Connector. The USB connector is used to power the optional subwoofer wireless
receiver. Do not plug in other USB devices into this port as it may damage the subwoofer
or the device. Refer to the wireless receiver installation instructions for more details.
5. Power Rocker Switch. Press the top this rocker switch to turn the subwoofer's master
power On. The subwoofer has an automatics signal-detection circuit. After approximately
ten minutes with no signal, the subwoofer will go into its quiet standby mode.
The presence of an audio signal will turn it back on. The signal-detection timeout period
can be adjusted in the companion smartphone app. Normally you can leave the switch
on, and let the subwoofer turn on when a signal is present, or turn off when it's not. At
night (or if you go out,or on vacation), you can press the bottom of the power switch to
turn the subwoofer off.
6. AC Line Fuse. The subwoofer is supplied with a conservative slow-blow type fuse to
protect the electronics. If this fuse fails, replace it with the exact same type and current
rating for your local AC voltage, as marked on the control panel near the fuse holder.
7. IEC Power Connector. The subwoofer comes with a detachable line cord that attaches
here. Make sure it is rmly pushed into place. Connect the other end to an AC outlet that
is properly congured for the type of plug and has the correct voltage for your model.
NOTE: Always unplug the power cord from your AC outlet before
removing the fuse. To replace or inspect the fuse, use a small athead
screwdriver to gently pry out the fuse carrier and fuse.
8. Voltage Selection Switch. This switch is used to select the compatible electrical voltage
for the location in which you're installing the subwoofer. Please check with your local
electrical requirements before making changes to this setting.
9. Mounting Standoffs. The mounting standoffs are used to mount the optional subwoofer
wireless receiver. Refer to the wireless receiver installation instructions for more details.

SpeakerCraft HRSi / XTEQi 6
10. Trigger (XTEQi-12 Only). 12V trigger input turns the amplier On or Off and
overrides the automatic signal detection circuit, reducing power consumption when
not in use. When this input receives a 12V signal, the subwoofer will turn ON. When the
signal goes away, the subwoofer will turn OFF.
11. Balanced IN (XTEQi-12 only). Balanced connections allow the use of very long
cables while reducing electrical interference. Connect a balanced output cable from your
receiver or preamp to the subwoofers Balanced IN.
12. Balanced OUT (XTEQi-12 only). These connect with Balanced type cables to
daisy-chain additional subwoofers or powered speakers. These outputs are pass-thru,
meaning they will pass through the same audio signal that is fed into the Balanced IN.
ON
OFF
STATUS
TRIGGER
BALANCE
IN
OUT
LOW LEVEL
OPTIONAL WIRELESS RECEIVER
POWER
100-120V~
220-240V~
FUSE T15AL/250V
100-120V~60Hz 12A
220-240V~50Hz 6A
USB POWER
5V 500mA
IN
OUT
L/LFER
XTEQi-12
➓
11
12

Nortek Security & Control LLC
7
Subwoofer placement
Subwoofer placement can greatly inuence its performance. All rooms are
different, but the loudest output will likely occur if the subwoofer is placed in a
corner of the room on the same wall as the front channel speakers.
You may need to experiment with more than one location, always testing the
sound from the primary listening position until you nd the right balance and
consistency in the bass performance.
You can also greatly improve subwoofer performance and eliminate many of
these placement challenges by using the AUTO EQ function in the companion
smartphone app.

SpeakerCraft HRSi / XTEQi 8
connectIng your Subwoofer (lfe)
If your processor or receiver has a subwoofer output (Sub/LFE), it should be
connected to the subwoofer’s LFE input as shown. This is the simplest and
recommended connection.
If you have a Home Theater processor or receiver, it probably has an
independent subwoofer volume and crossover control. If so, you should set
the subwoofer’s volume control to 50, the crossover to LFE, and use the
processor’s subwoofer level and frequency controls for adjustments.
AUDIO
OUTPUT
2 CH INPUT
SPEAKERS
CLASS 2 WIRING
AUDIO VIDEO
MAIN
MAIN
TUNER
DIGITAL
INPUT
R L
A
B
+
+
––
+
–
RCENTER L
R
CD DVD
CBL
AM
ANT
FM
ANT
GND
COAXIL
MONITOR
OUT
(LFE)
SUB
WOOFER
AUX
IN
MD/
CDR
IN
OPTICAL
OUT
OUT
VCR
MAIN
GRD
DVD
CENTER
SUB
WOOFER
L
R L
REAR
SURROUND
R L
➀
➁
ON
OFF
STATUS
LOW LEVEL OPTIONAL WIRELESS RECEIVER POWER
100-120V~ 220-240V~
FUSE T8AL/250V
100-120V~60Hz 6A
220-240V~50Hz 3A
USB POWER
5V 500mA
IN
OUT
L/LFE
R
HRSi
LFE Output
HRSi Subwoofer (back)

Nortek Security & Control LLC
9
If your processor or receiver does not have a Sub/LFE output, but has a stereo
output, you can connect a stereo RCA type cable from the stereo output to
the Low Level red and white inputs on the back on the subwoofer.
You can also use the optional subwoofer wireless receiver to send audio
from your source to the subwoofer. Refer to the wireless receiver installation
instructions for more details.
2-Channel
Amplier
LFE/
ON
OFF
STATUS
LOW LEVEL OPTIONAL WIRELESS RECEIVER POWER
100-120V~ 220-240V~
FUSE T8AL/250V
100-120V~60Hz 6A
220-240V~50Hz 3A
USB POWER
5V 500mA
IN
OUT
L/LFE
R
HRSi
Stereo Output
HRSi Subwoofer (back)
connectIng your Subwoofer (Stereo)

SpeakerCraft HRSi / XTEQi 10
confIgurIng your Subwoofer
The companion smartphone app allows you to setup and congure your
subwoofer from the comfort of your seating position. Download the app from
the Apple App Store or Google Play Store. Adjustments like volume, x-over
frequency, phase, etc., as well as the Auto EQ function, can be adjusted within
the app.
Subwoofer Discovery
1. Ensure that the power on the subwoofer is on and the status light is red or blue.
2. Launch the smartphone companion app and on the home screen select peripherals.
3. Select “Scan for devices” and hit “Connect” if prompted.
4. Repeat steps 1-3 for additional subwoofers. It is highly recommended to rename each
subwoofer so that it can be easily identied by its name when multiple subwoofers are
installed.
5. Your subwoofer(s) is now discovered and can be controlled from the companion
smartphone app.
Volume
1. Volume. Adjusts the volume output to the desired output level.
2. Preset. Makes EQ adjustments based on the type of material
you are playing. Music mode enhances performance while
listening to music while Movie mode enhances performance
while watching movies.
3. Night Mode. Compresses the subwoofer output when
watching a movie or playing music, so you don’t disturb
others.
4. Peripherals- Turn on Bluetooth. Toggles Bluetooth on and off.
Bluetooth must be turned on to congure the subwoofer with
the smartphone companion app.
5. Peripherals- Device name- Displays the current subwoofer
name. Can also be used to set a new subwoofer name.
6. Peripherals- Scan for devices. Scans for other subwoofers.

Nortek Security & Control LLC
11
Crossover
1. Crossover. Selects the low pass lter frequency and is
adjustable from 42Hz to 500Hz.
2. Variable/LFE toggle. Toggles between using the app to select
the low pass lter frequency and the AV Receiver selecting the
low pass lter frequency.
3. Slope. Adjusts the slope of the crossover frequency. The higher
the value, the steeper the cutoff.
Phase
1. Phase. Adjusts the signal delay of the incoming audio signal
and is used to better blend the audio from the subwoofer to
other speakers in the installation.
2. Variable/AVR Toggle. Toggles between using the app to select
the phase frequency and the AV Receiver selecting the phase
frequency.

SpeakerCraft HRSi / XTEQi 12
Delay
1. Delay. Sets the distance that the subwoofer is located
from the listening area and applies an acoustic delay to
compensate for the time that the audio from the subwoofer
takes to reach your ear. Adjustable from 5-80ft (1.5~24M)
2. Variable/AVR Toggle. Toggles between using the app to select
the delay and the AV Receiver selecting the delay.
3. Feet/Meters Toggle. Toggles between measurement in Feet
and Meters.
Manual EQ
Manual EQ. Allows you to manually adjust the
Frequency, Gain and Q of 4 independent EQs. Select
the EQ you would like to adjust using the radio
buttons labeled “EQ1, EQ2, EQ3, EQ4” then choose
the frequency, amount of gain or cut and Q using the
sliders.

Nortek Security & Control LLC
13
Using Auto EQ
Auto EQ is used to compensate for and correct for
acoustic room anomalies that can cause inferior bass
performance. Auto EQ takes a series of measurements
in and around your primary listening position, makes
complex calculations and applies those acoustic
corrections- all from the comfort of your listening area.
1. To begin Auto EQ, make sure that the Auto EQ toggle is turned
on, then press the Start button.
2. Choose up to 3 locations near your listening area and run
each sweep.
3. Once nished select “calculate” to apply the Auto EQ room correction to the subwoofer.
4. Repeat steps 1-3 for each additional subwoofer in the system.
Settings
1. Audio Sense. Sets the approximate time it takes before the
subwoofer goes into Standby mode when no audio signal
is present. You can select between 5, 10, 20, 30 minutes or
always on
2. Reset to Default. Puts the subwoofer back to its factory default
settings.
NOTE: Before you begin, be sure to shut
off all sources of ambient noise before
taking measurements. Failure to do so
may cause undesired/sub-optimal effects.

SpeakerCraft HRSi / XTEQi 14
SpecIfIcatIonS
HRSi-8
Woofer 8” High-excursion Fiberglass Cone with Big-Roll Surround
Frequency Response 24-200Hz
Amplier Power 1000 Watts Peak
Communication Type Bluetooth Low Energy
Crossover Frequency 40-500Hz
Dimensions (L x W x H) mm / inches 10.3” x 10.7” x 11.1” (262mm x 272mm x 282mm)
Voltage 100-120VAC or 220-240VAC Selectable
Cabinet 1” High Gloss MDF
HRSi-10
Woofer 10” High-excursion Fiberglass Cone with Big-Roll Surround
Frequency Response 24-200Hz
Amplier Power 1000 Watts Peak
Communication Type Bluetooth Low Energy
Crossover Frequency 40-500Hz
Dimensions (L x W x H) mm / inches 12.2” x 12.6” x 13” (310mm x 320mm x 330mm)
Voltage 100-120VAC or 220-240VAC Selectable
Cabinet 1” High Gloss MDF
HRSi-12
Woofer 12” High-excursion Fiberglass Cone with Big-Roll Surround
Frequency Response 20-200Hz
Amplier Power 1000 Watts Peak
Communication Type Bluetooth Low Energy
Crossover Frequency 40-500Hz
Dimensions (L x W x H) mm / inches 13.8"x14.2"x14.6" (351mm x 361mm x 371mm)
Voltage 100-120VAC or 220-240VAC Selectable
Cabinet 1” High Gloss MDF
XTEQi-12
Woofer Dual 12” High-excursion Kevlar Cone with Big-Roll Surround
Frequency Response 17-200Hz
Amplier Power 1000 Watts x 2 Peak
Communication Type Bluetooth Low Energy
Crossover Frequency 40-500Hz
Dimensions (L x W x H) mm / inches 19.2"x18.1"x17.7" (488mm x 460mm x 450mm)
Voltage 100-120VAC or 220-240VAC Selectable
Cabinet 1” High Gloss MDF

Nortek Security & Control LLC
15
lImIted 2-year warranty
Nortek Security & Control, LLC (“Nortek Security & Control”) warrants to the original retail purchaser only that this product will be
free of manufacturing defects in material and workmanship for the following periods and subject to the limitations and exclusions
set forth below:
2-Year Warranty
This warranty is not transferable to subsequent purchasers of the product. To obtain warranty service, contact the authorized
dealer where you purchased your product or take the unit to the nearest authorized dealer (with proof of purchase – claims
made without proof of purchase will be denied) who will test the product and if necessary, forward it to Nortek Security &
Control for service. If there are no authorized Dealers in your area, please contact Nortek Security & Control to receive a factory
Return Authorization Number. DO NOT RETURN ANY UNIT WITHOUT FIRST RECEIVING WRITTEN AUTHORIZATION AND SHIPPING
INSTRUCTIONS FROM Nortek Security & Control.
Upon examination, Nortek Security & Control will, at its sole option and expense, repair or replace any product found to be
defective. Nortek Security & Control will return the repaired or replaced unit to you via its usual shipping method from the factory
or repair center to your address in the United States of America or Canada only. Any shipping costs for addresses outside of the
United States or Canada shall be the responsibility of the purchaser. In the event that this model is no longer available and cannot
be repaired effectively, Nortek Security & Control, at its sole option, may replace it with a different model of equal or greater value,
or refund the original purchase price paid.
THE FOREGOING ARE YOUR EXCLUSIVE REMEDIES FOR BREACH OF WARRANTY.
This Warranty does not include service or parts to repair damage caused by improper use or handling, including but not limited to
damage caused by accident, mishandling, improper installation, commercial use, abuse, negligence, or any defect caused by repair
to the product by anyone other than Core Brands. This warranty does not cover reimbursement for your costs of removing and
transporting the product for warranty service evaluation, or installation of any replacement product provided under this warranty.
This Warranty will be void if:
- The Serial Number on the product has been removed, tampered with or defaced.
- The product was not purchased from an authorized dealer or reseller.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES.
NORTEK SECURITY & CONTROL EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT, WITH RESPECT TO THE
PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY LAW, NORTEK SECURITY & CONTROL SHALL NOT BE RESPONSIBLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES EXCEPT TO THE EXTENT PROVIDED (OR PROHIBITED) BY APPLICABLE LAW, EVEN IF
NORTEK SECURITY & CONTROL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Notwithstanding the above, if you qualify as a “consumer” under the Magnuson-Moss Warranty Act, or applicable state laws, then
you may be entitled to any implied warranties allowed by law for the Warranty Period. Further, some states do not allow limitations
on how long an implied warranty lasts or allow the exclusion or limitation of consequential damages, so such limitations may not
apply to you. This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
For the name of your nearest authorized dealer, contact: Nortek Security & Control, 5919 Sea Otter Place, Suite 100 Carlsbad, CA
92010, or call [phone] or [phone].
With regard to sales over the Internet, please be advised that Nortek Security & Control only sells products through a select group
of authorized Internet Resellers. Products offered on the Internet through unauthorized Internet dealers are not covered by Nortek
Security & Control.
1. Goods acquired on a secondary or gray market
2. Counterfeit or stolen goods
3. Damaged, or defective goods
Please ll in your product information and retain for your records.
Model ________________________________________
Serial # _______________________________________
Purchase Date __________________________________

attentIon: toour Valued cuStomerS
To ensure that consumers obtain quality pre-sale and after-sale support
and service, products are sold exclusively through authorized dealers. This
warranty is VOID if the products have been purchased from an unauthorized
dealer.
Nortek Security & Control offers a variety of accessories to make your
installation of this and other products easy, economical, and professional. To
learn more about our products, technologies and specications, go to: www.
nortekcontrol.com or contact your authorized Dealer for more information. For
technical inquiries, please call 1-800-448-0976.
In our attempt to constantly improve our products, features and specications
are subject to change without notice.
10030594 Rev-B
www.speakercraft.com
©2021 Nortek Security & Control LLC. All rights reserved. SpeakerCraft is a registered trademark of Nortek Security & Control LLC.
16