Nortek Security & Control 2GIG-RPTR1-345 User manual

Copyright © 2016 Nortek Security & Control LLC 1
2GIG-RPTR1-345
WIRELESS INDOOR REPEATER
INSTALLATION INSTRUCTIONS
The2GIGWirelessIndoorRepeater(2GIG‐RPTR1‐345)isaremotely
poweredwirelessindoorrepeater.Therepeaterisaperipheraldevice
thatcommunicateswiththe2GIGPanelusingaproprietary345MHz
transmissionprotocol.Therepeaterreceivesandrecognizesmessages
fromother345MHzdevicesthatareunabletodirectlycommunicate
withthesystem,and“repeats”thosemessagestoextendtherangeof
thesedevices.
Therepeaterwilltypicallybeinstalledatthemid‐pointbetweenthe
panelandthewirelessdevicesbeingrepeated.Whenatransmission
fromadeviceisrepeated,therepeateraddsabittothemessageto
indicatetothesystemthatthemessageisnotcomingdirectlyfrom
thedevice.Therepeaterwillnotrepeatalreadyrepeatedmessages.
TherepeaterispoweredbyanACadapterandisequippedwitha
rechargeablebatterywhichsupports24hoursofbatterybackup
underconditionsoflocalpowerfailure.Whenthepowersourcefor
therepeaterchangesfromACpowertobatterybackup,orfrom
batterybackuptoACpower,therepeaterwillautomaticallysenda
messagetothesystemwithintwo(2)minutes.Inaddition,
supervisorymessagesaresentapproximatelyevery70minutesthat
indicatetherepeaterstatus.
TherepeaterisequippedwithastatusindicatorLEDvisiblefromthe
frontoftheunit,andalearnbuttonislocatedonthesideoftheunit.
Figure 1 WirelessIndoorRepeaterPackageContents
Installing the Battery
Therechargeablebatterycanbeinstalledbyopeningtheenclosure
whilethepowerisdisconnected(seeFigure2).
WARNING: Polarityofthebatterymustbeobserved.Alignthe
batterytomatchthepolarityindicatorsonthecircuitboard.
Improperinstallationofthebatterymayresultinheat
generation,explosion,orfirewhichmayleadtopersonal
injury.
Installing the Repeater
Figure 2 Wireless Indoor Repeater Component and Feature Locations
Mounting Guidelines
Usetheseguidelineswheninstallingthewirelessindoorrepeater:
•MountRepeaterswithin100ft(30m)oftheControlPanel.
Althoughthetransmittermayhavearangeof350ft(106.7m)in
openair,therepeaterlocationcanhaveasignificanteffecton
range.Inopen/unobstructedsituations,thetransmitterrangemay
begreater.Inadversewirelessconditions,changingtherepeater
orientationmayleadtoimprovedrange.
•MountRepeatersashighaspossible.Mountingtherepeaterhigh
offthegroundhelpsreceiversensitivity.
•DoNotExposeRepeaterstoMoistureorExtremeTemperature.It
isbesttomountrepeatersinadrylocationwheretheoperating
temperaturedoesnotexceed32°to120°F(0°to49°C).
•KeepRepeatersAwayfromMetal/MetalicSurfaces.Tokeepthe
repeaterawayfrommetalormetallicsurfaces(forexample,foil
wallpaper),itisrecommendedthatyouusespacers(notincluded).
Youshouldalsoavoidmountingsensorsinareaswherethereisa
largequantityofmetalorelectricalwiring(forexample,neara
furnaceorinautilityroom).
Toinstallthewirelessrepeater:
1Opentherepeatercase.
2Attachthebasetothedesiredwalllocationwiththefour(4)
Phillipsheadscrewsandanchorssupplied(seeFigure2).
3Installthetamperscrew(seeFigure2).Withthetamperscrew
installed,removingthecasefromthewalltriggerstamper.
NOTE: Forthetampertoworkcorrectly,thetamperscrewmust
beinstalledintoawallstud.Donotuseawallanchor.
4Installthebattery.Observebatterypolarity.
5Connectthe2‐conductorwiretothepowersupplyandtothe
terminalconnectoronthecircuitboard.Makesurethewire
passesthroughthegrommetandholeontherepeaterbasebefore
connectingtotheterminal.
6Attachtherepeatercovertothebaseandsecuretheassembly
withthePhillipsheadcaselockingscrew.
ARechargeableLithium‐IonBattery
BACAdapter
CTamperScrew
DMountingScrewsandAnchors(4)
ELearnButton
FStatusIndicator
GPowerInput
HCaseLockingScrew
H
GF
E
B
A
C
D
1RechargeableLithium‐IonBattery 6RepeaterBase
2TamperSwitch 7TamperScrew
3Repeater 8MountingScrews(4)
4PowerInputConnector 9MountingAnchors(4)
5LearnButton
OBSERVE
BATTERY
POLARITY 12
3
4
5
6
7
8
9
PRINTER’S INSTRUCTIONS
10012437A-2GIG-RPTR1-345-INSTALL-INSTR-en-PRT, 09/16/2016, BLACK, 20LB MEAD BOND, 8.5X11”, TOL. +/- 0.125, SCALE: 1:1, FRONT & BACK, FOLD TO FIT BOX

2Copyright © 2016 Nortek Security & Control LLC
Wireless Indoor Repeater Installation Instructions
7PlugtheACadapterintoanACoutlet.Thestatusindicatorwill
emitasteadygreenlight.
NOTE: DonotconnecttheACadaptertoanACoutletthatis
controlledbyaswitch.
8Oncetherepeaterispoweredup,itbeginsrepeatingall
unrepeated345MHz2GIGtransmissions.
Status Indications
Thestatusindicatorshowstherepeaterstatusasfollows:
•SteadyGreen:TherepeaterisACpowered,andthebackup
batteryisgood.
•SolidRed:TamperorACpowerfailure.
•SlowFlashingRed:Lowbattery.
•FastFlashingRed:Jammed.
•Blinkoff:Transmissionreceived.
SPECIFICATIONS
OverallSize 102X76X46mm(4.0”X3.0”X1.8”)
Material High‐impactABSplastic
Color White
Weight(withoutbattery) 125g(4.4oz.)
InstallationType Wallmounted
OperatingFrequency 345MHz
OperatingTemperatureLimits ‐10°Cto55°C(14°Fto131°F)
RelativeHumidity 5to85%non‐condensing
PowerType RemotelypoweredbyACadapter,with
internalbatterybackup
ACAdapterNominalInputVoltage 100–240VAC50/60Hz
ACAdapterNominalOutputVoltage 14VDC
MaximumPowerConsumption 3W
IdleCurrent 40mA
OperatingCurrent(repeating) 75mA
StorageDeviceCapacity 800mAh(1)3.7V800mAh14500TypeLi‐
ionbattery(nottobereplaced)
REPEATER OPERATION
AND MESSAGE DESCRIPTIONS
SupervisoryMessage:
•Therepeatergeneratesasupervisorymessageevery70min
±10min.Themessagecontainsthecurrentbatterystatusand
tamperstate.
PowerUp:
•Whentherepeaterisfirstpoweredup,amessageisgenerated
containingthecurrentbatterylevelandtamperstate.
TamperMessage:
•Whentherepeaterdetectstamper,amessageissentcontaining
therepeaterstate,tamperstate,andbatterylevel.
EventMessage:
•Whentherepeaterreceivesamessage,themessageis
regeneratedwithanindicationthemessagehasbeenrepeated.
REGULATORY INFORMATION
2GIG
1950CaminoVidaRoble,Suite150
Carlsbad,CA92008USA
FortechnicalsupportintheUSAandCanada:
855‐2GIG‐TECH(855‐244‐4832)
Email:[e-mail]
Visitwebsitefortechnicalsupporthoursofoperation
FortechnicalsupportoutsideoftheUSAandCanada:
Contactyourregionaldistributor
Visit2gig.com/dealers/foralistofdistributorsinyourregion
ANortekCompany
10012437A
WARNING: Thisdeviceisnotdesignedtorepeatsignals
fromlifesafetydevicessuchasSmokeorCOdetectors.
This equipment has been tested and found to comply with the limits for Class B Digital
Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protecon against harmful interference in a residenal installaon. This equipment generates
and can radiate radio frequency energy and, if not installed and used in accordance with the
instrucons, may cause harmful interference to radio communicaons. However, there is
no guarantee that interference will not occur in a parcular installaon. If this equipment
does cause harmful interference to radio or television recepon, which can be determined by
turning the equipment offand on, the user is encouraged to try to correct the interference by
one or more of the following measures.
Reorient or relocate the receiving antenna
Increase the separaon between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modificaons not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. Ľexploitaon est autorisée aux deux condions suivantes: (1)
ľappareil ne doit pas produire de brouillage, et (2) ľulisateur de ľappareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est suscepble ďen compromere le
fonconnement.
FCC COMPLIANCE STATEMENT
This device complies with FCC Rules and Regulaons as Part 15 devices as well as Industry
Canada license exempt RSS Rules and Regulaons. Operaon is subject to the following two
(2) condions: This device may not cause harmful interference. This device must accept any
interference received, including interference that may cause undesired operaon.
LIMITED WARRANTY
This Nortek Security & Control LLC product is warranted against defects in material and
workmanship for two (2) years. This warranty extends only to wholesale customers who
buy direct from Nortek Security & Control LLC or through Nortek Security & Control normal
distribuon channels. Nortek Security & Control does not warrant this product to consumers.
Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty,
if any.
There are no obligaons or liabilies on the part of Nortek Security & Control for consequenal
damages arising out of or in connecon with use or performance of this product or other
indirect damages with respect to loss of property, revenue, or profit, or cost of removal,
installaon, or reinstallaon. All implied warranes for funconality, are valid only unl the
warranty expires. This Nortek Security &Control Warranty is in lieu of all other warranes
expressed or implied.