NorthEast Monitoring DR400 User manual

DR400 Quick Start Guide
To purchase more patch electrodes contact your distributor or go to www.nemon.com
STEP
D ESCRIPTION
S TEPS /H INTS
1
Fully charge the
DR400
Use a power source (not the PC) to charge the DR400
Remove from power source when orange light stops blinking
2
Enter Patient ID
using PCPatch
Utility
If you have not already done so, save and delete previous
patient’s data from the DR400 using the PCPatch utility
before entering new Patient ID
3
Prepare patient
Determine the best location to attach the patch and optional
lead wire onto the patient, but do not attach at this time
Prepare the patient’s skin. If the patient has hair in any of the
patch site, shave it with a safety razor. Use an alcohol pad
and rub the sites briskly until the skin reddens. Let the skin air
dry before proceeding.
4
Prepare DR400
and attach to
patient
Attach 1-lead electrode patch (1CH) or 1-lead electrode patch
w/ lead wire (3CH)to the DR400 recorder
Remove backing from leads and attach firmly to patient
5
Start Recording
by holding the
DR400 “EVENT”
button down
until green light
goes out
If you so choose, start the PCPatch utility before starting the
DR400 to confirm start up and observe lead quality
The DR400 will flash green for 30 seconds at the start of the
recording
At any time, press EVENT button again to transmit Bluetooth
signal to view ECG via PCPatch utility
6
Stop Recording
and Upload data
for analysis
Remove from patient and plug DR400 into the PC USB cable
and the DR400 will stop recording after 2 minutes
Start PCPatch utility to save DR400 data to HE/LX patient
directory
Open HE/LX Analysis to view and analyze patient data
The PCPatch Utility
Hook-up Guide
Download PCPatch at www.nemon.com
and install on PC where analysis software
is installed.
Note: You do not need a Bluetooth USB
Adapter to use the DR400. The adapter is only
required to view ECG using the PCPatch utility. Contact
your distributor to find out more about this feature.
1-lead electrode patch
(1CH)
Snap Guide
If using the 1-lead electrode patch with the optional
ECG lead wire:
•Attach the ECG lead wire first
•ECG lead wire attaches to
snap closest to USB port
The lead plastic should cover
the USB port
To attach the 1-lead electrode
patch for 3CH recording:
Patch goes on diagonally
Press down firmly so that all
snaps are locked in place
1-lead patch w/ lead wire
(3CH)
Copyright 2019
Last updated: July 19, 2019
NEMM049 - Rev-A - English
You must download and install the PCPatch Utility at
www.nemon.com before getting started.

DR400 FUNCTIONS:
FUNCTION
DO THIS
LIGHT
Which means:
TO START
RECORDING
When in Standby
mode, hold
EVENT button
down until green
light goes out
(about 3 seconds)
DR400 will flash
for 30 seconds

The DR400 flashes for about 30 seconds
to tell you that recording has started.
DR400 shows
solid orange light
instead

Recording did not start as there is either
old data OR no Patient ID on the DR400.
Use the PCPatch utility to save and/or
delete the data and enter new Patient
ID.
DR400 does not
respond

Recording did not start. Most likely, the
DR400 battery is not charged.
Charge via USB power source.
If charged or plugged into USB and no
light is visible, contact Customer Support
for further assistance.
TO RECORD
EVENT
While recording,
press EVENT
button
DR400 will flash
green for about
15 seconds

An event has been saved
TO VIEW
ECG
While recording,
start PCPatch
utility and then
press EVENT
button
DR400 will flash
green while
transmitting

To make this work, the DR400 must be
paired with the NorthEast Bluetooth
USB and the PCPatch utility must be
running on machine where the
Bluetooth USB is attached. An event will
also be saved at this time.
TO STOP
RECORDING
Attach DR400 to
USB cable for at
least 2 minutes
DR400 is
connected to PC

DR400 will stop recording
TO SAVE
ECG &
UPDATE
SETTINGS
Attach DR400 to
PC where PCPatch
utility is running
DR400 is
connected to PC

Use the PCPatch utility to preview, save
the flash.dat file, erase the DR400, pair
the DR400 with Bluetooth and update
settings.
DR400 MODES:
MODE
LIGHT
WHICH MEANS
Notes:
STANDBY
No light

DR400 is not in use
Quickly press the EVENT button. 1) If the
DR400 light does not go on, the DR400 is not
charged. If you are not sure the DR400 is fully
charged, charge it now;
2) If the DR400 flashes green, the DR400 is
recording and is not in Standby mode.
RECORDING
No light

The DR400 is storing
data
While recording, if you press the EVENT
button, the recorder will flash green for about
10 seconds
CONNECTED
TO PC
Green –
solid

DR400 is connected to
the PC
Once removed from power source, the DR400
will flash quickly for 15 seconds before return
to STANDBY mode
DATA
TRANSFER
Fast green -
flashing

DR400 is transferring
data or DR400 removed
from USB
Flash.dat file being copied to Patient directory,
or DR400 removed from USB and resetting
ERASING
Alternating


Data on recorder being
erased
This can only be done using PCPatch
CHARGING
Orange –
flashing

DR400 is connected to
power source and is
charging
Once removed from power source, the DR400
will return to STANDBY mode
FULLY
CHARGED
Orange -
solid

DR400 is connected to
power source and is
fully charged
Once removed from power source, the DR400
will return to STANDBY mode
IP44
DR400 Functions and Modes
MediMark Eruope, SARL
11 rue Emile Zola
BP 2332
F-38033 Grenoble CEDEX 2
France 0143