norwellVR. NWJR503 User manual

IN-GROUND
INSTALLATION MANUAL

INSTALLATION MANUAL ·IN-GROUND
www.norwell.dk · [e-mail] COPYRIGHT © 2015 Norwell A/S
Dig holes according to positions on
drawings (see the following pages).
Tighten the anchors (M12 = 90 N/m
and M16 = 120 N/m).
Dimensions of holes:
e.g. 50 x 50 x 75 cm (see the
following pages).
Drill bolt holes with a concrete
hammer.
Make sure the fitness station is stabil
and properly fastened before filling
with dirt to the surface.
Fill with concrete leaving a depth of
e.g. 25/40 cm (see the following
pages). Dry for approx. 6-7 days.
Mount the M12/M16 concrete
bolts.
REQUIREMENTS FOR THE CONCRETE
The concrete must comply with the standard EN197-1 CEM I 52,5 N.
Mixing ratio: Cement 1/8
Sand 3/8 (max. stone size 4mm)
Stones 4/8 (stone size 16mm)
The concrete must be premixed or mixed in a mixer. Hand mixing is not
acceptable.
For the concrete to settle, it must be vibrated with a concrete vibrator.
To ensure correct contact between the base plate and the concrete, the
concrete surface must be 100% plane.
The concrete has to have the strength of ≥52,5 MPa (obtained in approx.
7 days, but longer in cold weather).
The installation must be carried out by professionals and according to current
practice.

NWJR102
Junior Back
NWJR101
Junior Chest
2,10m
INSTALLATION MANUAL ·IN-GROUND
www.norwell.dk · [e-mail] COPYRIGHT © 2015 Norwell A/S
See separate page with the
preparatory work for in-ground
installation.
• Install onto a concrete block.
• Assemble and line up.
• Place on concrete.
• Mark position of bolt holes.
• Fasten each base plate with
4 x M16 bolts.
POSITION AND TRAINING ZONE: DEPTH:
PART LIST:
4 x M16
BASE PLATE:
40 x 40cm
0,75m
0,25m
0,50m
0,70m
CONCRETE
BLOCK

NWJR103 Junior Sit Up
INSTALLATION MANUAL ·IN-GROUND
www.norwell.dk · [e-mail] COPYRIGHT © 2015 Norwell A/S
See separate page with the
preparatory work for in-ground
installation.
• Install onto 2 concrete blocks.
• Assemble and line up.
• Place on concrete.
• Mark position of bolt holes.
• Fasten each base plate with
4 x M12 bolts.
POSITION AND TRAINING ZONE: DEPTH:
0,50m
0,50m
0,75m
0,25m
CONCRETE
BLOCK
PART LIST:
8 x M12
BASE PLATE:
25 x 25cm

NWJR104 Junior Pull Up
2,12m
INSTALLATION MANUAL ·IN-GROUND
www.norwell.dk · [e-mail] COPYRIGHT © 2015 Norwell A/S
See separate page with the
preparatory work for in-ground
installation.
• Install onto 2 concrete blocks.
• Assemble and line up.
• Place on concrete.
• Mark position of bolt holes.
• Fasten each base plate with
4 x M16 bolts.
POSITION AND TRAINING ZONE: DEPTH:
0,50m
1,00m
0,75m
0,25m
CONCRETE BLOCK
PART LIST:
8 x M16
BASE PLATE:
40 x 40cm

NWJR105 Junior Bar
INSTALLATION MANUAL ·IN-GROUND
www.norwell.dk · [e-mail] COPYRIGHT © 2015 Norwell A/S
See separate page with the
preparatory work for in-ground
installation.
• Install onto 2 concrete blocks.
• Assemble and line up.
• Place on concrete.
• Mark position of bolt holes.
• Fasten each base plate with
4 x M12 bolts.
POSITION AND TRAINING ZONE: DEPTH:
0,50m
0,50m
0,75m
0,25m
CONCRETE
BLOCK
PART LIST:
8 x M12
BASE PLATE:
25 x 25cm

NWJR201 Junior Double Air Walker
INSTALLATION MANUAL ·IN-GROUND
www.norwell.dk · [e-mail] COPYRIGHT © 2015 Norwell A/S
See separate page with the
preparatory work for in-ground
installation.
• Install onto 6 concrete blocks.
• Assemble and line up.
• Place on concrete.
• Mark position of bolt holes.
• Fasten each base plate with
4 x M12 bolts.
ASSEMBLING:
POSITION AND TRAINING ZONE: DEPTH:
0,50m
0,50m
0,75m
0,25m
CONCRETE
BLOCK
PART LIST:
24 x M12
2 x cross bar
2 x sets of Nut caps, round
4 x M10 x 110 bolts
4 x Stainless Steel connector
Always secure
bolts with
Loctite.
BASE PLATE:
25 x 25cm

NWJR202 Junior Cross
1,42m / 4’7”
INSTALLATION MANUAL ·IN-GROUND
www.norwell.dk · [e-mail] COPYRIGHT © 2015 Norwell A/S
See separate page with the
preparatory work for in-ground
installation.
• Install onto a concrete block.
• Assemble and line up.
• Place on concrete.
• Mark position of bolt holes.
• Fasten each base plate with
4 x M16 bolts.
POSITION AND TRAINING ZONE: DEPTH:
PART LIST:
4 x M16
BASE PLATE:
40 x 40cm
0,50m
0,70m
0,90m
0,40m
CONCRETE
BLOCK

NWJR203 Junior Hip
INSTALLATION MANUAL ·IN-GROUND
www.norwell.dk · [e-mail] COPYRIGHT © 2015 Norwell A/S
See separate page with the
preparatory work for in-ground
installation.
• Install onto 2 concrete blocks.
• Assemble and line up.
• Place on concrete.
• Mark position of bolt holes.
• Fasten each base plate with
4 x M12 bolts.
POSITION AND TRAINING ZONE: DEPTH:
0,50m
0,50m
0,75m
0,25m
CONCRETE
BLOCK
PART LIST:
8 x M12
BASE PLATE:
25 x 25cm

NW501 Bench
INSTALLATION MANUAL ·IN-GROUND
www.norwell.dk · [e-mail] COPYRIGHT © 2015 Norwell A/S
See separate page with the
preparatory work for in-ground
installation.
• Install onto 4 concrete blocks.
• Assemble and line up.
• Place on concrete.
• Mark position of bolt holes.
• Fasten each base plate with
4 x M12 bolts.
ASSEMBLING:
POSITION AND TRAINING ZONE: DEPTH:
0,50m
0,50m
0,75m
0,25m
CONCRETE
BLOCK
PART LIST:
16 x M12
4 x sets of Nut caps, round
4 x M10 x 110 bolts
Always secure
bolts with
Loctite.
BASE PLATE:
25 x 25cm

NWJR502 Junior Ping Pong
INSTALLATION MANUAL ·IN-GROUND
www.norwell.dk · [e-mail] COPYRIGHT © 2015 Norwell A/S
POSITION AND TRAINING ZONE: DEPTH:
0,50m
0,50m
0,75m
0,25m
CONCRETE
BLOCK
See separate page with the
preparatory work for surface
mount installation.
• Install onto surface.
• Assemble and line up.
• Place on concrete.
• Mark position of bolt holes.
• Fasten each base plate with
4 x M12 bolts.
PART LIST:
16 x M12
10 x M10x12 bolts
BASE PLATE:
25 x 25cm / 10” x 10”

1
2
3
3
1
INSTALLATION MANUAL ·IN-GROUND
www.norwell.dk · [e-mail] COPYRIGHT © 2015 Norwell A/S
INSTRUCTION FOR ASSEMBLING
NWJR502 Junior Ping Pong
See separate page for position,
zone and concrete area require-
ments.
1Bolt the 5 table top supports
to the side frames.
2Place the net right in the center
vertically and horizontally.
It has the same width as the
table tops.
3Add the Multi Glue on top of
all supports, both upper frames
and on top of the foot of the
net.
4Two people hold one table top
over the frame and all the way
up to the net. Make sure to
center the top on all sides,
lower down and press the top
against frame and supports.
5Repeat with the next table top.
Table top
supports
Foot of
the net
The net
The side frames
Always secure bolts
with Loctite.
Add the supplied
Multi Glue.

NWJR503 Junior Sign
INSTALLATION MANUAL ·IN-GROUND
www.norwell.dk · [e-mail] COPYRIGHT © 2015 Norwell A/S
See separate page with the
preparatory work for in-ground
installation.
• Install onto 2 concrete blocks.
• Assemble and line up.
• Place on concrete.
• Mark position of bolt holes.
• Fasten each base plate with
4 x M12 bolts.
ASSEMBLING:
DEPTH:
0,50m
0,50m
0,75m
0,25m
CONCRETE
BLOCK
PART LIST:
8 x M12
4 x sets of Nut caps, straight
4 x M8 x 12 bolts
Always secure
bolts with
Loctite.
BASE PLATE:
25 x 25cm