NOTHERN TVIBIR65 User manual

TVIBIR65
HD-TVI Full HD 1080p Outdoor 65’ IR Bullet
Rev. 102115
 3625 Cincinnati Avenue, Rocklin, CA 95765 i 855-388-7422 i www.northernvideo.com
Installation & Quick Setup Guide
Regulatory Information
FCC Information
FCC compliance: This equipment has been
tested and found to comply with the limits for a
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
EU Conformity Statement
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive):
This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European
Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European
Union. For proper recycling, return
this product to your local supplier
This product and - if applicable - the
supplied accessories too are marked
with "CE" and comply therefore with
the applicable harmonized European
standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC,
the RoHS Directive 2011/65/EU.
This series of camera adopts new generation
sensor with high sensitivity and advanced circuit
design technology.It features high resolution,
low image distortion and low noise, etc., which
makes it suitable for surveillance system and
image processing system.
High performance CMOS sensor and high
resolution bring high-quality image;
Low illumination;
OSD menu, parameters are configurable;
Support auto white balance, auto gain control,
electronic shutter control;
Support image effect adjustment;
Unit transmission control;
Advanced 3-axis design meets different
installation requirements.
1 Introduction
1.1 Product Features
1.2 Overview
1.2.1 Overview of Type I Camera
2 Installation
Before you start:
Please make sure that the device in the package
is in good condition and all the assembly parts
are included.
Make sure that all the related equipment is
power-off during the installation.
Check the specification of the products for the
installation environment.
Check whether the power supply is matched
with your power output to avoid damage.
Please make sure the wall is strong enough to
withstand three times the weight of the camera
and the mounting.
If the wall is the cement wall, you need to insert
expansion screws before you install the camera.
If the wall is the wooden wall, you can use
self-tapping screw to secure the camera.
If the product does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
Steps:
1.Drill the screw holes in the ceiling according
to the supplied drill template.
2.Hammer the supplied plastic expansion bolt into
the screw holes.
2.1 Wall & Ceiling Mounng
Figure 2-1 Drill Template
3.Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4.Fix the camera to the ceiling with the supplied screws.
ScrewHole
ScrewHole
ScrewHole
HD Video Cable
Power Cable
Mounting Base
Sun Shield
Lens
IR LED
960H Video Cable
5.Adjust the surveillance angle.
1).Loosen No.3 adjusting ring to adjust the
panning position (0° ~ 360°).
2).Tighten No.3 adjusting ring.
3).Loosen the No.2 adjusting screw to adjust the
tilting position (0° ~90°).
4).Tighten No.2 adjusting screw.
5).Loosen No.1 adjusting screw to adjust the
azimuth angle of the image (0°~ 360°).
6).Tighten No.1 adjusting screw.
Figure 2-3 3-axis Adjustment
Figure 2-2 Fix the Camera to the Ceiling or Wall
WallCeiling
3 6 0°
9 0°
3 6 0°
1
2
3
Thank you for purchasing our product. If there
are any quesons, or requests, please do not
hesitate to contact us.
This manual may contain several technical
incorrect places or prinng errors, and the
content is subject to change without noce.
The updates will be added to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
Privacy Noce
Surveillance laws vary by jurisdicon. Check all
relevant laws in your jurisdicon before using
this product for surveillance purposes to ensure
that your use of this product conforms.
Please refer to the product specificaon for
camera parameters and funcons.

d screws.
3 Menu Operaon
Menu
SCENE LENS RESET
EXPOSUREWB DAY&NIGHT
BACKLIGHTNR SPECIAL ADJUST
INDOOR
OUTDOOR
INDOOR1
LOW-
LIGHT
MANUALSHUTTER
AGC
SENS-UP
BRIGHTNESS
D-WDR
DEFOG
BLC
HSBLC
ATW
AWC-SET
INDOO R
OUTDOOR
MANUAL
COLOR
B/W
EXT
2D NR
3D NR
CAM
TITLE
D-EFFECT
MOTIO N
PRIVACY
LAUGUAGE
DEFECT
VERSION
SHARPN ESS
MONIT OR
LSC
VIDEO.
OUT
EXIT
SETUP
3.1 VIDEO.OUT
PAL or NTSC is selectable .
3.2 LANGUAGE
English, Japanese, CHN1, CHN2, Korean, German,
French, Italian, Spanish, Polish, etc., are selectable.
3.3SETUP
3.3.1 SCENE
You can select indoor, outdoor, indoor 1 and low
-light as the working environments.
3.3.2 LENS
The camera is equipped with a fixed lens.
3.3.3 EXPOSURE
EXPOSURE
1. SHUTTER AUTO
2. AGC OFF
3. SENS-UP ---
4. BRIGHTNESS---|------ 40
5. DEFOG OFF
6. BACKLIGHT OFF
7. RETURN RET
Figure 3-2 Exposure
SHUTTER: AUTO,1/25, 1/50, FLK, 1/200, 1/400,
1/1k, 1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10,
and x15 are selectable.
: You can set the AGC value from 0 to 15.AGC
: You can set the SENS-UP to OFF or AUTO.SENS-UP
: You can set the brightness valueBRIGHTNESS
from 1 to 100.
: You can set the D-WDR to ON to improveD-WDR
the image quality or OFF to disable the funcon.
: You can set the defog funcon as ON toDEFOG
enable the funcon. Posion, size, and the defog
gradaon are configurable.
3.3.4 Backlight
Backlight Compensaon (BLC):
Set the gain of BLC as High, Middle, or Low.-GAIN:
Press the up/down/le/right buon to-AREA:
define the BLC posion and size. Select RET or
AGAIN to go back the BLC menu or re-define the
BLC area.
Restore the BLC sengs to the default.-Default:
HSBLC: Select an HSBLC area. Set the DISPLAY
status as ON. Press the up/down/le/right buon
to define the area posion and size. Set the HSBLC
LEVEL from 0 to 100. Select ALL DAY or Night for the
HSBLC mode. Set the BLACK MASK status as ON or
OFF.
HSBLC
1. SELECT AREA 1
2. DISPLAY ON
3. LEVEL ---|------ 40
4. MODEALLDAY
5. BLACK MASK ON
6. DEFAULT
7. RETURN RET
Figure 3-3 HSBLC
3.3.5 White Balance (WB)
INDOOR, OUTDOOR, MANUAL, ATW (Auto-tracking
White Balance), AWC→SET are selectable.
3.3.6 Day & Night
Color, B/W, and EXT are selectable for DAY and
NIGHT switches.
3.3.7 NR
: You can set 2D NR status as ON or OFF.2D NR
: Set the Smart NR status as ON and adjust3D NR
the 3D smart NR sensivity ranges from 0 to 100.
Set the 3D NR LEVEL ranges from 0 to 100. Set the
2D&3D NR
1. 2DNR OFF
2. 3DNR ON
3. RETURN RET
3D NR
1. SMART NR ON
2. LEVEL ------|--8 0
3. START. AGC -|--------10
4. END. AGC -|--------10
5. RETURN RET
Figure 3-5 NR
Figure 3-6 3D NR
3.3.8 SPECIAL
Edit the camera tle on this secon.Camera Title:
D-effect:
Set the freeze funcon as ON or OFF.-FREEZE:
OFF, MIRROR, V-FLIP, and ROTATE are-MIRROR:
selectable for mirror.
Define the zoom area by configuring-D-ZOOM:
the posion from PAN & TILT.
The D-Zoom area, sensivity-SMART D-ZOOM:
and me are configurable.
Set the NEG IMAGE as ON or OFF.-NEG.IMAGE:
SPECIAL
1. CAM TITLE ON
2. D-DFFECT
3. MOTION OFF
4. PRIVACY OFF
5. LANGUAGE ENG
6. DEFECT
7. VERSION130722
8. RETURN RET
Figure 3-7 Special
MOTION
1. SELECT AREA 1
2. DISPLAY ON
3. SENSITIVITY ----|---- 30
4. MOTION VIEW ON
5. DEFAULT
6. RETURN RET
Figure 3-8 Moon Detecon
Moon: Select a MOTION area. Set the DISPLAY
status as ON or OFF. Press the up/down/le/right
buon to define the posion and size of the area.
Set the SENSITIVITY from 0 to 60. Set the MOTION
VIEW status as ON or OFF.
Privacy: Select a PRIVACY area. Set the DISPLAY
status as INV, MOSAIC, COLOR or OFF. Press the
up/down/le/right buon to define the posion
and size of the area.
Defect: LIVE DPC, STATIC DPC and Black DPC are
adjustable in this secon.
: You can check the soware version of theVersion
device.
PRIVACY
1. SELECT AREA 1
2. DISPLAYMOSAIC
3. COLOR 10
4. TRANS. 1
5. DEFAULT
6. RETURNRET
ADJUST
1. SHARPNESS --------|15
2. MONITOR LCD
3. LSC OFF
4. VIDEO. OUT PAL
5. RETURNRET
3.3.9 ADJUST
: Adjust the sharpness from 0 to 15.Sharpness
: Monitor CRT, and Monitor LCD areMonitor
selectable.
: Set the LSC status as ON or OFF.LSC
3.3.10 RESET
Reset all the sengs to the default.
3.3.11 EXIT
Press OK to exit the menu.
START. AGC level as the threshold to enable AGC,
and set the END. AGC level as the threshold to
disable AGC.
Figure 3-9 Privacy MaskFigure 3-10 Adjust
Figure 3-1 Main Menu
You can call the menu and adjust the camera
parameters with a coaxial camera controller
(purchase separately). You can also call the menu
with supported TVI DVR.