Nova FPA-0-1821 series User manual

FRONT EDGE
A
21/2"
(64 mm )
4
"
(102 mm )
1-1/4"
(Offset 32mm)
(Typ.)
3/16" Dia.
5/8" Deep
6 Places
Model #
Figure 1A
FPA-0-1821
Step 1.
Cut opening for viewport. (Figure 1A). Prepare surface for keyboard
drawer (Figure 1B).
Step 2.
Using the desk bracket (B) as a template, locate and drill bracket holes
(Figure 1A). Note drill size and hole depth!
Step 6. Install trim ring & viewport glass
Step 3.
Page 1
IIR017 FPA-0-1821 Widescreen Asy. Instr. 01/2012 © Nova Solutions, Inc. 2012
IIR017 FPA-0-1821 Widescreen Asy. Instr. © Nova Solutions, Inc. 2012
Retrofit Kit
Assembly Instructions
Page 2
Patents pending.
The natural way to look at a computer™
-24, -27, -28, -30, -33, -34
Flat Panel Display Arm
Figure 4
1. Locate screen as high as possible without raising glass.
2. Aim screen slightly above user’s eyes. (Bottom of screen should be
closer to eyes than top of screen.)
3. Preferred location is with top edge of flat panel display at back
edge of glass.
4. For semi-recessed positions, remove viewport glass and
raise flat panel display.
FRONT EDGE
1/2"(12.7 mm) R.
All corners
UNDERSIDE OF TOP
24"(609.6 mm) Minimum Depth Of Worksurface
0.25"
3"
(76 mm )
Center on
viewport opening
D
L
Desk Bracket
Adjustment
VESA Plate
Adjustment
IMPORTANT: The longer screws
(L) pass through the tubular
section of the keyboard
hanger. That allows the
assembly to be leveled by
loosening or tightening the
screws.
Attach
keyboard
hangers (F,G, Figure
5) to underside of
worksurface with screws
(D, E). Insert outward
locking tab (R) by pulling it
forward to lock in place.
Q
321/8"(816 mm)
KB drawer size Dimension A
2219/32"(574 mm)24"
255/16"(643 mm)
27"
261/8"(664 mm)
28"
281/16"(713 mm)
30"
311/4"(794 mm)
33"
34"
F
G
L
D
Snap trim ring
pieces (N, O1, O2) together.
Insert into viewport cutout
and attach with screws
(M). Carefully insert
viewport glass into trim
ring. Slide keyboard
tray into glides.
O1
N
O2
24"
(609.6 mm )
18 ¼"
(464 mm)
The arm ships with two VESA plates. Determine the one you need by holding VESA
plates up to the attachment holes on the back of the monitor. Select the one where
all four holes line up with the VESA plate holes.
Includes
Flat panel display arm,
keyboard drawer,
visor, glass &
trim ring
PACKING LIST
FPA-8-2006
Align holes in desk mounting bracket (B) with holes in worksurface
(Figure 2). Attach using screws (D).
WARNING: Removing the set screws or oiling the joints could cause
the flat panel display to fall and void the warranty.
Figure 5
Step 5
Step 4. Attach flat panel display to VESA plate
Remove flat panel display base. Attach flat panel display to VESA plate
with screws (E, Figure 3). Depress silver spring pin on VESA plate
extension tube and slide it into the desk mount extension tube. Tighten
wing nut (C, Figure 4). See "Monitor Angle" for adjustment guidance.
When installing some Apple® flat panel displays, a VESA Adapter
(Model #50-8-4100) may be necessary. Contact Customer Support
for more information.
Figure 2
DESK BRACKET
3/16" Dia.
5/8" Deep
6 Places
1.26"(32 mm)
1.26"
(32 mm)
D
C
B
A1
A2
S
Back edge of cut-out
Figure 3
Display
E
100 mm
(3-15/16")
4-7/16"
100 mm
(3-15/16")
75 mm
(2-15/16")
3-3/4"
75 mm
(2-15/16")
A1 A2
Extension tubes
viewport cut-out
C
320°
270°
Monitor Angle
20 11/16""
(526
mm )
Widescreen Format
QTY REF # ITEM # DESCRIPTION
1 A1 75 mm *VESA plate
1 A2 100 mm *VESA plate
1 B Desk bracket
1 C
924B-2520-0-50A Wing nut
10 D 1412APPBO Screw, #14 x 3/4"
4 E 50900219 Screw, Silver,
4mm x 0.7 x 10
1 F 20060126 Keyboard hanger w/ glide - left
1 G 20060127 Keyboard hanger w/ glide - right
1 H Varies Keyboard drawer
1 J AC-SG10721821W Viewport glass
2 L 50900032 Screw - #14 x 1-1/2"
4 M 6N50TXPZ Security screw #6 x 5/8"
4 N 50900034 Trim ring corner
2 O1 50900035 Trim ring straight - B
2 O2 50900036 Trim ring straight - A
1 P 5081062 Visor
2 Q FR2121/Clip Locking tab
4 S
10628-03819 Screw, Black, 4mm x 0.7 x 8
*VESA 75/100 Standard
Figure 1B - Hole pattern for keyboard drawer
P.O. Box 725 • 421 W. Industrial Avenue • Effingham, Illinois 62401 • Phone: [phone] • Fax: [phone] • [email protected] • www.novadesk.com

FRONT EDGE
A
2
1
/ 2 "
(64 mm )
4
"
(102 mm )
1-1/4"
(Offset 32mm)
(Typ.)
3/16" Dia.
5/8" Deep
6 Places
Model #
Figure 1A
FPA-0-1821
Step 1.
Cut opening for viewport. (Figure 1A). Prepare surface for keyboard
drawer (Figure 1B).
Step 2.
Using the desk bracket (B) as a template, locate and drill bracket holes
(Figure 1A). Note drill size and hole depth!
Step 6. Install trim ring & viewport glass
Step 3.
Page 1
IIR017 FPA-0-1821 Widescreen Asy. Instr. 01/2012 © Nova Solutions, Inc. 2012
IIR017 FPA-0-1821 Widescreen Asy. Instr. © Nova Solutions, Inc. 2012
Retrofit Kit
Assembly Instructions
Page 2
Patents pending.
The natural way to look at a computer™
-24, -27, -28, -30, -33, -34
Flat Panel Display Arm
Figure 4
1. Locate screen as high as possible without raising glass.
2. Aim screen slightly above user’s eyes. (Bottom of screen should be
closer to eyes than top of screen.)
3. Preferred location is with top edge of flat panel display at back
edge of glass.
4. For semi-recessed positions, remove viewport glass and
raise flat panel display.
FRONT EDGE
1/2"(12.7 mm) R.
All corners
UNDERSIDE OF TOP
24"(609.6 mm ) Minimum Depth Of Worksurface
0.25"
3"
(76 mm )
Center on
viewport opening
D
L
Desk Bracket
Adjustment
VESA Plate
Adjustment
IMPORTANT: The longer screws
(L) pass through the tubular
section of the keyboard
hanger. That allows the
assembly to be leveled by
loosening or tightening the
screws.
Attach
keyboard
hangers (F,G, Figure
5) to underside of
worksurface with screws
(D, E). Insert outward
locking tab (R) by pulling it
forward to lock in place.
Q
321/8"(816 mm)
KB drawer size Dimension A
2219/32"(574 mm)24"
255/16"(643 mm)
27"
261/8"(664 mm)
28"
281/16"(713 mm)
30"
311/4"(794 mm)
33"
34"
F
G
L
D
Snap trim ring
pieces (N, O1, O2) together.
Insert into viewport cutout
and attach with screws
(M). Carefully insert
viewport glass into trim
ring. Slide keyboard
tray into glides.
O1
N
O2
24"
(609.6
mm )
18 ¼"
(464 mm)
The arm ships with two VESA plates. Determine the one you need by holding VESA
plates up to the attachment holes on the back of the monitor. Select the one where
all four holes line up with the VESA plate holes.
Includes
Flat panel display arm,
keyboard drawer,
visor, glass &
trim ring
PACKING LIST
FPA-8-2006
Align holes in desk mounting bracket (B) with holes in worksurface
(Figure 2). Attach using screws (D).
WARNING: Removing the set screws or oiling the joints could cause
the flat panel display to fall and void the warranty.
Figure 5
Step 5
Step 4. Attach flat panel display to VESA plate
Remove flat panel display base. Attach flat panel display to VESA plate
with screws (E, Figure 3). Depress silver spring pin on VESA plate
extension tube and slide it into the desk mount extension tube. Tighten
wing nut (C, Figure 4). See "Monitor Angle" for adjustment guidance.
When installing some Apple® flat panel displays, a VESA Adapter
(Model #50-8-4100) may be necessary. Contact Customer Support
for more information.
Figure 2
DESK BRACKET
3/16" Dia.
5/8" Deep
6 Places
1.26"(32 mm)
1.26"
(32 mm)
D
C
B
A1
A2
S
Back edge of cut-out
Figure 3
Display
E
100 mm
(3-15/16")
4-7/16"
100 mm
(3-15/16")
75 mm
(2-
15
/ 16 ")
3-3/4"
75 mm
(2-15/16")
A1 A2
Extension tubes
viewport cut-out
C
320°
270°
Monitor Angle
20 11/16""
(526 mm )
Widescreen Format
QTY REF # ITEM # DESCRIPTION
1 A1 75 mm *VESA plate
1 A2 100 mm *VESA plate
1 B Desk bracket
1 C
924B-2520-0-50A Wing nut
10 D 1412APPBO Screw, #14 x 3/4"
4 E 50900219 Screw, Silver,
4mm x 0.7 x 10
1 F 20060126 Keyboard hanger w/ glide - left
1 G 20060127 Keyboard hanger w/ glide - right
1 H Varies Keyboard drawer
1 J AC-SG10721821W Viewport glass
2 L 50900032 Screw - #14 x 1-1/2"
4 M 6N50TXPZ Security screw #6 x 5/8"
4 N 50900034 Trim ring corner
2 O1 50900035 Trim ring straight - B
2 O2 50900036 Trim ring straight - A
1 P 5081062 Visor
2 Q FR2121/Clip Locking tab
4 S 10628-03819 Screw, Black, 4mm x 0.7 x 8
*VESA 75/100 Standard
Figure 1B - Hole pattern for keyboard drawer
P.O. Box 725 • 421 W. Industrial Avenue • Effingham, Illinois 62401 • Phone: [phone] • Fax: [phone] • [email protected] • www.novadesk.com