Nova FPA-0-2124-27 User manual

FRONT EDGE
A
2
1
/ 2 "
(64 mm )
4
"
(102 mm )
1-1/4"
(Offset 32mm)
(Typ.)
3/16" Dia.
5/8" Deep
6 Places
Model #
Figure 1A
FPA-0-2124
Step 1.
Cut opening for viewport. (Figure 1A). Prepare surface for keyboard
drawer (Figure 1B).
Step 2.
Using the hole pattern on the desk mount extension tube (B1) as a
template, locate and drill holes (Figure 1A). Note drill size and hole depth!
Step 6. Install trim ring & viewport glass
Step 3.
Page 1
IIR018Bb FPA-0-2124 Widescreen Asy. Instr. 05/20/13 © Nova Solutions, Inc. 2013
IIR018b FPA-0-2124 Widescreen Asy. Instr. © Nova Solutions, Inc. 2013
Retrofit Kit
Assembly Instructions
Page 2
Patents pending.
The natural way to look at a computer™
-27, -28, -30, -33, -34
Flat Panel Display Arm
1. Locate screen as high as possible without raising glass.
2. Aim screen slightly above user’s eyes. (Bottom of screen should be
closer to eyes than top of screen.)
3. Preferred location is with top edge of flat panel display at back
edge of glass.
4. For semi-recessed positions, remove viewport glass and
raise flat panel display.
D
L
VESA Plate
Adjustment
IMPORTANT: The longer screws
(L) pass through the tubular
section of the keyboard
hanger. That allows the
assembly to be leveled by
loosening or tightening the
screws.
Q
321/8"(816 mm)
KB drawer size Dimension A
2219/32"(574 mm)24"
255/16"(643 mm)
27"
261/8"(664 mm)
28"
281/16"(713 mm)
30"
311/4"(794 mm)
33"
34"
F
G
L
D
O1
N
O2
The arm ships with two VESA plates. Determine the one you need by holding VESA
plates up to the attachment holes on the back of the monitor. Select the one where
all four holes line up with the VESA plate holes.
Includes
Flat panel display arm,
keyboard drawer,
visor, glass &
trim ring
PACKING LIST
Align holes in desk mount extension tube (B1) with holes in
worksurface (Figure 2). Attach using screws (D). Using 4 screws (S),
attach VESA plate (A1 or A2) to VESA plate extension tube (B2).
WARNING: Removing the set screws or oiling the joints could cause
the flat panel display to fall and void the warranty.
Figure 5
Step 5
Step 4.
Attach flat panel display to VESA plate
Figure 2
DESK MOUNT EXT. TUBE
1.26"(32 mm)
1.26"
(32 mm)
320°
270°
Monitor Angle
Widescreen Format
Figure 1B - Hole pattern for keyboard drawer
P.O. Box 725 • 421 W. Industrial Avenue • Effingham, Illinois 62401 • Phone: [phone] • Fax: [phone] • [email protected] • www.novadesk.com
Figure 4
Attach
keyboard
hangers (F,G, Figure
5) to underside of
worksurface with screws
(D, L). Insert locking tab
(R) then pull it forward to
lock in place.
Snap trim ring
pieces (N, O1, O2) together.
Insert into viewport cutout
and attach with screws
(M). Carefully insert
viewport glass (J) into
trim ring. Slide
keyboard tray into
glides.
Remove flat panel display base. Attach flat panel display to VESA
plate (using screws located on the back of your flat panel display,
supplied by the manufacturer). See Figure 3.
Depress silver spring pin on VESA plate extension tube and slide it
into the desk mount extension tube. Tighten wing nut (C, Figure 4).
See "Monitor Angle" for adjustment guidance.
When installing some
Apple® flat panel displays, a VESA Adapter (Model #50-8-4100) may
be necessary. Contact Customer Support for more information.
A1
B1 A2
S
Back edge of cut-out
Figure 3
Display
100 mm
(3-15/16")
4-7/16"
100 mm
(3-15/16")
75 mm
(2-
15
/ 16 ")
3-3/4"
75 mm
(2-15/16")
viewport cut-out
Silver spring pin
Desk mount
Extension tube VESA plate
Extension tube
C
B2
C
D
A1 A2
FRONT EDGE
1/2"(12.7 mm) R.
All corners
3"
(76 mm )
Center on
viewport opening
1/4"
27-1/4"
(692 mm)
21-1/4"
(540 mm)
QTY REF # ITEM # DESCRIPTION
1 A1 75 mm *VESA plate
1 A2 100 mm *VESA plate
1 B Desk bracket
1 C
924B-2520-0-50A Wing nut
10 D 1412APPBO Screw, #14 x 3/4"
1 F 20060126
Keyboard hanger w/ glide - left
1 G 20060127 Keyboard hanger w/ glide - right
1 H Varies Keyboard drawer
1 J 5081073 Viewport glass
2 L 50900032 Screw - #14 x 1-1/2"
4 M 6N50TXPZ Security screw #6 x 5/8"
4 N 50900034 Trim ring corner
2 O1 50900037 18” Trim ring straight (C)
2 O2 50900038 21” Trim ring straight (D)
1 P 5081062 Visor
2 Q FR2121/Clip Locking tab
4 S 10628-03819 Screw, Black, 4mm x 0.7 x 8
*VESA 75/100 Standard
FPA-8-2006
3/16" Dia.
5/8" Deep
6 Places
24-1/4"
(616 mm )
UNDERSIDE OF TOP CLEARANCE
27 1/4"(692 mm ) Minimum Clearance Depth Of Worksurface

FRONT EDGE
A
2
1
/ 2 "
(64 mm )
4
"
(102 mm )
1-1/4"
(Offset 32mm)
(Typ.)
3/16" Dia.
5/8" Deep
6 Places
Model #
Figure 1A
FPA-0-2124
Step 1.
Cut opening for viewport. (Figure 1A). Prepare surface for keyboard
drawer (Figure 1B).
Step 2.
Using the hole pattern on the desk mount extension tube (B1) as a
template, locate and drill holes (Figure 1A). Note drill size and hole depth!
Step 6. Install trim ring & viewport glass
Step 3.
Page 1
IIR018Bb FPA-0-2124 Widescreen Asy. Instr. 05/20/13 © Nova Solutions, Inc. 2013
IIR018b FPA-0-2124 Widescreen Asy. Instr. © Nova Solutions, Inc. 2013
Retrofit Kit
Assembly Instructions
Page 2
Patents pending.
The natural way to look at a computer™
-24, -27, -28, -30, -33, -34
Flat Panel Display Arm
1. Locate screen as high as possible without raising glass.
2. Aim screen slightly above user’s eyes. (Bottom of screen should be
closer to eyes than top of screen.)
3. Preferred location is with top edge of flat panel display at back
edge of glass.
4. For semi-recessed positions, remove viewport glass and
raise flat panel display.
D
L
VESA Plate
Adjustment
IMPORTANT: The longer screws
(L) pass through the tubular
section of the keyboard
hanger. That allows the
assembly to be leveled by
loosening or tightening the
screws.
Q
321/8"(816 mm)
KB drawer size Dimension A
2219/32"(574 mm)24"
255/16"(643 mm)
27"
261/8"(664 mm)
28"
281/16"(713 mm)
30"
311/4"(794 mm)
33"
34"
F
G
L
D
O1
N
O2
The arm ships with two VESA plates. Determine the one you need by holding VESA
plates up to the attachment holes on the back of the monitor. Select the one where
all four holes line up with the VESA plate holes.
Includes
Flat panel display arm,
keyboard drawer,
visor, glass &
trim ring
PACKING LIST
Align holes in desk mount extension tube (B1) with holes in
worksurface (Figure 2). Attach using screws (D). Using 4 screws (S),
attach VESA plate (A1 or A2) to VESA plate extension tube (B2).
WARNING: Removing the set screws or oiling the joints could cause
the flat panel display to fall and void the warranty.
Figure 5
Step 5
Step 4. Attach flat panel display to VESA plate
Figure 2
DESK MOUNT EXT. TUBE
1.26"(32 mm)
1.26"
(32 mm)
320°
270°
Monitor Angle
Widescreen Format
Figure 1B - Hole pattern for keyboard drawer
P.O. Box 725 • 421 W. Industrial Avenue • Effingham, Illinois 62401 • Phone: [phone] • Fax: [phone] • [email protected] • www.novadesk.com
Figure 4
Attach
keyboard
hangers (F,G, Figure
5) to underside of
worksurface with screws
(D, L). Insert locking tab
(R) then pull it forward to
lock in place.
Snap trim ring
pieces (N, O1, O2) together.
Insert into viewport cutout
and attach with screws
(M). Carefully insert
viewport glass (J) into
trim ring. Slide
keyboard tray into
glides.
Remove flat panel display base. Attach flat panel display to VESA
plate (using screws located on the back of your flat panel display,
supplied by the manufacturer). See Figure 3.
Depress silver spring pin on VESA plate extension tube and slide it
into the desk mount extension tube. Tighten wing nut (C, Figure 4).
See "Monitor Angle" for adjustment guidance.
When installing some
Apple® flat panel displays, a VESA Adapter (Model #50-8-4100) may
be necessary. Contact Customer Support for more information.
A1
B1 A2
S
Back edge of cut-out
Figure 3
Display
100 mm
(3-15/16")
4-7/16"
100 mm
(3-15/16")
75 mm
(2-
15
/ 16 ")
3-3/4"
75 mm
(2-15/16")
viewport cut-out
Silver spring pin
Desk mount
Extension tube VESA plate
Extension tube
C
B2
C
D
A1 A2
FRONT EDGE
1/2"(12.7 mm) R.
All corners
3"
(76 mm )
Center on
viewport opening
1/4"
27-1/4"
(692 mm)
21-1/4"
(540 mm)
QTY REF # ITEM # DESCRIPTION
1 A1 75 mm *VESA plate
1 A2 100 mm *VESA plate
1 B Desk bracket
1 C
924B-2520-0-50A Wing nut
10 D 1412APPBO Screw, #14 x 3/4"
1 F 20060126
Keyboard hanger w/ glide - left
1 G 20060127 Keyboard hanger w/ glide - right
1 H Varies Keyboard drawer
1 J 5081073 Viewport glass
2 L 50900032 Screw - #14 x 1-1/2"
4 M 6N50TXPZ Security screw #6 x 5/8"
4 N 50900034 Trim ring corner
2 O1 50900037 18” Trim ring straight (C)
2 O2 50900038 21” Trim ring straight (D)
1 P 5081062 Visor
2 Q FR2121/Clip Locking tab
4 S 10628-03819 Screw, Black, 4mm x 0.7 x 8
*VESA 75/100 Standard
FPA-8-2006
3/16" Dia.
5/8" Deep
6 Places
24-1/4"
(616 mm )
UNDERSIDE OF TOP CLEARANCE
27 1/4"(692 mm ) Minimum Clearance Depth Of Worksurface