NOVO Annie STA-FRA-NAT-60 User manual

ASSEMBLY INSTRUCTIONS
IMPORTANT
Please Inspect all items carefully before assembling. If for any reason you need to return
this item, you must return it in its original packaging. Assembled items cannot be returned.
Please open the zip on the back of the headboard.
You may find the footboard and some of the components inside
Minimum No.of people recommended to assemble this product: Two (2)
Approx. Assembly time: 90 mins
HELPFULADVICEPRIORTOASSEMBLINGTHEBED
1) Owing to the size and weight of the bed, we recommend that it is assembled by two adults,
on a flat surface in a room that it is intended for.
2) Please Do Not use any tools other than those provided or recommended in these instructions.
3) Please Do Not discard any packaging until you have checked that you have all the parts and fittings.
Keep all fittings out of reach of children.
4) Assemble all parts loosely until advised to tighten. Depending on use, it maybe necessary to tighten
the fittings from time to time, So please save your Allen key and Spanner that has beed provided.
5) Do Not throw away any of the packaging or the instructions booklet until you have checked all
the components and fittings and the furniture is fully assembled.
Page 1 of 6
STA-FRA-NAT-60STA-FRA-GREY-60STA-FRA-BLUE-60

1 2
3
567
8910
Headboard Footboard X1 X1
X2
X4 X8
X42 X1
12 X28
CentralSlat Cap
X4
Feet
Slat Headboard Ear A
X1
Siderail L
Centre Rail Support Leg
Transverse Rail
Components
4X2
Siderail R
11 X1
Headboard Ear B
Page 2 of 6

AConnection Plate Left 2
×
BConnection Plate Right 2
×
C
D
E
F
H
I
G
M8*25mm Bolt
Nut
M6*20mm Bolt
JM8*45mm Bolt
8
×
2
×
24
×
4
×
Allen key M5
Allen key M4
Spanner
8
×
M6*25mm Bolt K4*25mmScrew 16
×
2
×L
2
×
2
×
M6*35mm Bolt
Washer 4
×
Connection Three-hole
Connection Four-hole
Screw driver(not provided)
Hardware
Page 3 of 6

Step 1: Secure the Headboard ear A
10 & Headboard ear B 11 to the
Headboard 1 using Bolt J and
Allen key M5
Step 2a : Secure Connection
Three-hole C & Connection
Four-hole F to Siderail A 3 &
Siderail A 3 and Siderail B 4 &
Siderail B 4 using Bolt I ,
Washer L and Allen Key
Step 2b : Secure Connection Plate
Left A & Right B to Siderail B
4 & Siderail A 3 using Bolt I
and Allen Key
Step 2c : Secure Connection Plate
Left A & Right B to Headboard
1 & Footboard 2 using Bolt D
and Allen Key
WORNG CORRECT
NB: Before tightening the bolts, please ensure the bed frame is square
Step 1:
Step 2:
Page 4 of 6

Step 3: Secure the four Feet 7 to
the bottom of the Headboard 1 and
Footboard 2 & Siderail A 3 and
Siderail B 4 , using Screw K and
Screw driver
Step 4d: Secure Support leg 6 to
Central 5 & Transverse rail 9 ,
using Bolt E and Allen key M4
Step 4a: Secure Transverse 9 to
Connection Three-hole C using
Bolt E , Nut M6 G and
Spanner
Step 4c: Secure Support leg 6 to
Central 5 and Transverse rail 9 ,
using Bolt H and Allen key M4
Step 4b: Secure Central Rail 5 to
Headboard 1 and Footboard 2 ,
using Bolt I and Allen key M4
Step 3:
Step 4:
Page 5 of 6

Step 5：Slot the slats 8 into the
central slat cap 12 and Siderail A
3 & Siderail B 4 as shown.
Attach slats to the Centre Rail 5
then firmly press into place After
this step , please fully tighten all
bolts if you check all the parts are
positioned.
Step 5:
Page 6 of 6