NOVO Victoria HLX-OTT-BLUE-60 User manual

ASSEMBLY INSTRUCTIONS
IMPORTANT
Please Inspect all items carefully before assembling. If for any reason you need to return
HLX-OTT-BLUE-60HLX-OTT-NAT-60
this item, you must return it in its original packaging. Assembled items cannot be returned.
Please open the zip on the back of the headboard.
You may find the footboard and some of the components inside
Minimum No.of people recommended to assemble this product: Two (2)
Approx. Assembly time: 90 mins
HELPFULADVICEPRIORTOASSEMBLINGTHEBED
1) Owing to the size and weight of the bed, we recommend that it is assembled by two adults,
on a flat surface in a room that it is intended for.
2) Please Do Not use any tools other than those provided or recommended in these instructions.
3) Please Do Not discard any packaging until you have checked that you have all the parts and fittings.
Keep all fittings out of reach of children.
4) Assemble all parts loosely until advised to tighten. Depending on use, it maybe necessary to tighten
the fittings from time to time, So please save your Allen key and Spanner that has beed provided.
WARNINGS
1) Please ensure children Do Not play in the storage area or try to lift up the metal frame.
2) Once assembled, put mattress on frame before pushing it down and only lift up or push down the
metal frame with mattress on top.
3) Please Do Not stand on the storage base at any time.
4) Do Not throw away any of the packaging or the instructions booklet until you have checked all
the components and fittings and the furniture is fully assembled.
HOW TO USE BED
When the bed is fully assembled, Lift the frame up using strap on the footboard. To close the frame you
will need to place both hands on the horizontal metal bar at the footboard end that is in the air ( one
hand in the centre of each of the two rows of slats). The bed will only work if this done centrally. Apply
pressure to close the bed. Do Not try to close from the side or any other way. Please also notethe gaslift
lift arms do not move up and down on their own and only work if the bed is fully assembled and is
assembled correctly and will only work normally with mattress on the frame.
PLEASE LOCATE FOOTBOARD AND FITTINGS INSIDE THE ZIPPED
COMPARTMENT BEHIND THE HEADBOARD PAGE 1 of12

Page 2 of 12
12
3
4
13
8
7
15
21
17
18
14
20
16
22
23
12
24
HeadboardFootboard
Siderail Left
Siderail Right
Cross Rail of Headboard
Side rail of Metal Frame
CentralSupport Bar
Cross Rail of Footboard
Support Leg
Central
Support Block
Corner Angle Bracket
Cross Rail
Mattress stopper
Slat
EndSlat Cap
CentralSlat Cap
Pneumatic cylinder
Non-Woven Fabric
9Connection bar
X1 X1
X1
X1
X1
X2
X2
X1
X4
X4
X2
X1
X2
X45
X30
X30
X2
X1
X2
10
11
Folding mechanism (R)
Folding mechanism (L)
X1
X1
5ear Right
Headboard
Components
6ear Left
Headboard

AConnection Plate Left 2
×
BConnection Plate Right 2
×
C
D
E
F
H
I
G
M8*20mm Bolt
Washer
Nut
M8*15mm Bolt
M6*20mm Bolt
JM8*35mm Bolt
16
×
12
×
4
×
30
×
4
×
8
×
Allen key M5
Allen key M4
Spanner
4
×
8
×
M6*35mm Bolt
M6*70mm Bolt LM8*40mm Bolt4
×
Hardware
Page 3 of 12

Step 2a : Secure Support block
17 to the Headboard 1 and
Footboard 2 using Bolt E and
Allen Key M4
Step 2b : Secure Folding
mechanism-Right 10 & Left 11
and Connection bar 9 to Siderail
4 & Siderail 3 using Bolt J and
Allen Key
Step 2a
Step 2b
Step 1a : Secure Connection
Plate Left A & Right B to
Siderail B 4 & Siderail A 3
using Bolt D and Allen Key M5
Step 1b : Secure Connection Plate
Left A & Right B to Headboard
1 & Footboard 2 using Bolt D
, Washer F and Allen Key M5
Step 1c : Secure the two Corner
Angle brackets 18 to the Footboard
2 using Bolt I and Allen Key
D
A
Step 1b
F
D
A
I
Step 1c
B
A
B
A
Step 1a
Step 1:
Step 2:
Page 4 of 12
WORNG CORRECT
NB: Before tightening the bolts, please ensure the bed frame is square

Step 5b
H
Step 5a
Step 5a : Slot in Mattress stopper
20 to Cross rail of Headboard 13
Step 5b : Secure Folding meachanism
10 & 11 to Side rail of metal frame 8
using Bolt H and Allen key
Step 4a : Secure Cross rail of
Headboard 13 & Cross rail of
Footboard 15 to Side rail of
metal frame 8 using Bolt H
and Allen key
Step 4c :Secure Central support
leg 21 to Central support bar 7
using Bolt H and Allen key
Step 4b :Secure Central support
rail 7 to Cross rail of Headboard
13 and Cross rail of Footboard
15 , using Bolt H and Allen key
M5
Step 4a
Step 4b
Step 4c
HH
H
Step 4:
Step 5:
Page 5 of 12

Secure Cross rail 14 to Siderail
4 & Siderail 3 using Bolt C
and Allen Key M4
Step 6:
Step 7:
Page 6 of 12
Attach the Non Woven fabric Base
Turn bed on its side and attache
the Non-woven fabric 24 to the
Velcro strip on the underside of
the edge of the bed base.

G
Step 8: Slot the slats 16 into the
end slat cap 22 and central slat
cap 23 as shown.
Attach slats 16 to the side rails
of metal frame 8 and central
support bar 7 then firmly press
into place.
After this step , please fully
tighten all bolts if you check all
the parts are positioned
Secure Pneumatic cylinder 12 to
folding mechanism 10 & 11 using
Nut G and Spanner
Step 8:
Step 9:
Page 7 of 12

L
Step 10:
Secure Headboard ear 5 and 6 to
Headboard 1 using Bolt L , Washer
F and Allen Key M5
Page 8 of 12
F