Novus NVIP-TDN3401H/IR/MPX2.0 User manual

U s e r ’s m a n u a l
NVIP-TDN3401H/IR/MPX2.0

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
2
IMPORTANT SAFEGUARDS AND WARNINGS
EMC (2004/108/EC) and LVD (2006/ 5/EC ) Directives
CE Marking
Our products are manufactured to comply with requirements of the following directives and national regulations
implementing the directives:
• Electromagnetic compatibility EMC 2004 108 EC.
• Low voltage LVD 2006 95 EC with further amendment. The Directive applies to electrical
equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as
75VDC and 1500VDC.
WEEE Directive 2002/ 6/EC
Information on Disposal for Users of Waste Electrical and Electronic Equipment
This appliance is marked according to the European 1000VAC Directive on Waste Electrical and Electronic
Equipment (2002 96 EC) and further amendments. By ensuring this product is disposed of correctly, you will
help to prevent potential negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product.
The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be
treated as household waste. It shall be handed over to the applicable collection point for used up electrical and
electronic equipment for recycling purpose. For more information about recycling of this product, please contact
your local authorities, your household waste disposal service or the shop where you purchased the product.
RoHS Directive 2002/ 5/EC
Out of concern for human health protection and friendly environment, we assure that our products
falling under RoHS Directive regulations, regarding the restriction of the use of hazardous
substances in electrical and electronic equipment, have been designed and manufactured in
compliance with the above mentioned regulations. Simultaneously, we claim that our products have
been tested and do not contain hazardous substances whose exceeding limits could have negative
impact on human health or natural environment
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed for self
installation in households by individuals without technical knowledge.
Excluding of responsibility in case of damaging data on a disk or other devices:
The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices
during device operation.
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN
USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES
NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE
CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR
THE RESULTS OF SUCH AN ACTION.

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0
All rights reserved © AAT Holding sp. z o.o.
3
IMPORTANT SAFEGUARDS AND WARNINGS
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER
DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH
THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO
USER-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE
PERSONNEL MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
1. Prior to undertaking any action please consult the following manual and read all the safety and operating
instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is
necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s
manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer is
forbidden;
7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,
damp basements);
8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not
recommended since it may lead to heat build-up and damaging the device itself as a consequence;
9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly
mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted
by qualified personnel with proper authorization, in accordance with this user’s manual.
10. Device should be supplied only from a power sources whose parameters are in accordance with those
specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera
from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
4
TABLE OF CONTENTS .................................................................................................... 4
1. FOREWORD INFORMATION................................................................................... ..6
1.1. General Characteristics ....................................................................................... 6
1.2. NVIP-TDN3401H IR MPX2.0 tech specification ......................................... ...7
1.3. Camera dimensions .......................................................................................... ...8 1.4.
Package contents ................................................................................................................ ...8
2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 9
2.1. Description of crucial connectors and control tools............................................ 9
2.2. NVIP-TDN3401H IR MPX2.0 mounting......................................................... 10
2.3. Starting the IP camera ....................................................................................... 10
2.4. Initial configuration via the Web browser ........................................................ 11
3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................ 12
3.1. Recommended PC specification for web browser ............................................. 12
3.2. Connection with IP camera via the Internet Explorer........................................ 12
3.3. Connection with IP camera via the Mozilla Firefox.......................................... 14
4. WWW INTERFACE - WORKING WITH IP CAMERA ........................................ 16
4.1. Displaying live pictures. .................................................................................... 16
4.2. Camera configuration......................................................................................... 17
4.2.1. System settings .......................................................................................... 18
a. System information .................................................................................. 18
b. User management..................................................................................... 19
c. System update .......................................................................................... 20
4.2.2. Network ..................................................................................................... 21
a. IP Settings ................................................................................................ 21
b. DDNS....................................................................................................... 23
4.2.3. A V settings ............................................................................................... 24
a. Picture settings ......................................................................................... 24
b. Video settings........................................................................................... 25
c. Sound settings ......................................................................................... 26
TABLE OF CONTENTS

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0
All rights reserved © AAT Holding sp. z o.o.
5
4.2.4. Event settings............................................................................................. 27
a. Events....................................................................................................... 27
b. Schedule................................................................................................... 29
c. I O Settings .............................................................................................. 30
d. Mail & FTP .............................................................................................. 31
e. Log list ..................................................................................................... 32
5. ELECTRIC CONNECTORS AND ACCESORIES ................................................. 33
5.1. Description of camera connectors...................................................................... 33
5.2. Connecting alarm inputs outputs ...................................................................... 34
6. RESTORING FACTORY DEFAULTS .................................................................... 35
6.1. Restoring software factory defaults ................................................................... 35
6.2. Restoring hardware factory defaults in IP cameras .......................................... 35
TABLE OF CONTENTS

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
6
1. FOREWORD INFORMATION
1.1. General Characteristics
• Pick-up element resolution: 2.0 Mpix
• Mechanical IR cut filter, IR operation capability
• Min. Illumination 0.5 lx F=1.5, 0 lx (IR on)
• Aspheric lens f=3.6~16 mm ,
• Built-in IR LED - 35 LEDs
• Alarm input and output
• Bidirectional audio transmission
• H.264, MPEG-4, MJPEG video compression
• 1600x1200 maximum video processing resolution
• RTP RTSP protocol for audio video transmission support
• Triple streaming operation: features adjustable compression, resolution, speed and quality for two
streams.
• Mobile PDA support via additional 3GPP stream
• Hardware motion detection
• 3 independent privacy zones
• Pre - and post-alarms - recording in AVI format
• Wide array of event notification methods: FTP server, E-Mail, alarm output activation, storage of
video file (avi) or image file (jpeg) on the Samba server.
• Schedule
• HTTP, TCP IP, UDP, FTP, DHCP, DDNS, NTP, 3GPP, RTSP, UPnP support
• Software supported: NMS (NOVUS MANAGEMENT SYSTEM - video recording, live view,
playback and remote IP configuration)
• PoE (Power over Ethernet) support
• 12 VDC (230 VAC 12 VDC power supply included) power supplied
FOREWORD INFORMATION

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0
All rights reserved © AAT Holding sp. z o.o.
7
FOREWORD INFORMATION
1.2. NVIP-TDN3401H/IR/MPX2.0 specification
* Processing speed available for selected camera configuration (details provided further in the manual)
Model
NVIP-TDN3401H/IR/MPX2.0
Pick-up Element 1/3” MOS imager
Imager Resolution 2.0 megapixels
Min. Illumination 0.5 lx F=1.5
0 lx (IR on)
Electronic Shutter Auto (AES)
Digital Slow Shutter (DSS) 0.03 ~ 0.2 s
Privacy zones 3
Back Light ompensation (BL ) On/Off
Day/night switching automatic, manual, timer, external
Image Settings brightness, contrast, sharpness
Lens Mount auto iris D-type lens, f=3.6 ~ 16 mm
Angle of View (H) 54° ~ 19°
Video Output BN , 1.0 V
p-p
, 75 Ohm
IR LED LED - 35 pcs.
IR Effective Range Up to 20 m
Audio Input 1 x Jack (3,5mm)
Audio Output 1 x Jack (3,5mm)
Video ompression H.264 / MPEG-4(tryb 3GPP) / M-JPEG
Audio ompression µ-Law
Resolution 1600x1200 (UXGA), 1280x1024 (SXGA), 1280x960, 1280x720 (HD720),
800x592 (SVGA), 640x480 (VGA), 320x240 (QVGA), 176x144 (Q IF)
Alarm Input 1, voltage
Alarm Output 1 relay output (NO/N ) - max. 1 A, 24 VD or 0.5 A, 125 VA
Pre- & Post-alarm Functions Max. 5 s pre-alarm and max. 10 s post-alarm recording with adjustment
possibility
Frame Rate
Up to 15 fps for 1600 x 1200*,
Up to 22 fps for 1280 x 1024*,
Up to 25 fps for 1280x960*,
Up to 30 fps 1280x720 and lower resolutions
Motion detection Hardware
Video Saving Files AVI, JPEG sequence, JPEG
Event History Log Up to 250 events for each group (Alarm, Motion detection, System logs)
User Authorization Password protected camera access and configuration
Simultaneous connection Max. 10
External Ports 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s
Time Synchronization Automatic time synchronization with NTP server
Network Protocols Support HTTP, T P/IP, UDP, FTP, DH P, DDNS, NTP, 3GPP, RTSP, UPnP
Software NMS
User Authorization Password protected camera access and its configuration
Degree of protection IP 66
PoE Yes
Power supply 12 VD (230 VA /12 VD PSU in-set included)
Power consumption 6 W (IR OFF) / 8.5W (IR ON)
Operation temperature -10° ~ 45°
Dimensions (mm) 180 (L) x 83 ( Ø )
Weight 1220 g
System reaction to alarm event E-mail with attachment, saving file on FTP, saving file on Samba server,
alarm output activation

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
8
1.3. Camera dimensions
1.4. Package contents
After you open the package make sure that the following elements are inside:
• IP camera
• 230 VAC 12 VDC power supply
• Accessories bag
• Short version of user’s manual
• CD containing manual and software
If any of this elements has been damaged during transport, pack all the elements back into the original
box and contact your supplier for further assistance.
CAUTION!
If the device was brought from a location with lower temperature, please wait until it reaches the
temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.
FOREWORD INFORMATION

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0
All rights reserved © AAT Holding sp. z o.o.
9
2. START-UP AND INITIAL IP CAMERA CONFIGURATION
2.1. Description of crucial connectors and control tools
NVIP-TDN3401H/IR/MPX2.0
START-UP AND INITIAL CAMERA CONFIGURATION
1. IR LED
2. Light sensor
3. Focus adjustment
4. Zoom adjustment
5. RJ-45 Ethernet adapter
6. Alarm I O connector block
7. Audio input (red socket)
8. Audio output (green socket)
9. BNC output for connecting additional external monitor
10. RJ-45 Ethernet plug
11. 12V DC power connector
1
2
3
4
5 9 6 7 8 10 11

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
10
START-UP AND INITIAL CAMERA CONFIGURATION
2.2. NVIP-TDN3401H/IR/MPX2.0 mounting
To mount a camera please follow the instructions below:
• Put the camera’s base to wall ceiling.
• Taking holes at the bottom of the camera’s base as a pattern, please mark the drilling holes
(using a punch, for example) for screws and cables
• Drill holes, in accordance with camera’s base hole placement.
• Drill cable hole in the mounting place.
• Put cable through its dedicated hole, screw the camera to a mounting surface using appropriate
screws.
• Remove protecting sticker from the camera’s front
• Set zoom and focus using appropriate screws and adjusting rings
• Set camera position and block adjustment screw
2.3. Starting the IP camera
To run NOVUS IP camera you have to connect it to power source via power supply adapter. Next,
connect the Ethernet cable between the PC or network switch and IP cameras. After connecting power
supply green LED located at the camera front should start blinking indicating start of the initialization
process witch takes about 30 seconds. You can then proceed to connect to the camera via web browser.
If the connection is successfully established green LED blinks with a frequency proportional to the
quantity of data sent. Connecting via web browser is then possible. If connection isn’t established (the
network cable is disconnected) the LED isn’t active, solid light means that network connection is ok
but camera doesn't receive or send any data, with possible PC network settings error.
The recommended way to start an IP camera and perform its configuration is a connection through
crossover cable with your PC or laptop. To obtain further information about network configuration
parameters (IP address, gateway, network mask, etc.) please contact your network administrator.
Network configuration of camera can be done by web browser or NMS software using default network
IP address: 192.168.1.200
Cross-over cable
IP camera PC

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0
All rights reserved © AAT Holding sp. z o.o.
11
2.5. Initial configuration via the web browser
The default network settings for NVIP-T… IP camera series are :
1. IP address= 1 2.168.1.200
2. Network mask - 255.255.255.0
3. Gateway - 1 2.168.1.254
4. User name - root
5. Password - pass
Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can
operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from
192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for
camera and PC computer
You can set network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera or select
DHCP mode (DHCP server is required in this method in target network) by using web browser or by
NMS software. When you use DHCP server check IP address lease and its connection with camera
MAC address to avoid changing or losing IP address during device operation or network DHCP server
breakdown. You have to remember to use a new camera IP address after changing network parameters.
After network setting configuration has been done, the camera can be connected to a target network.
START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
12
3. NETWORK CONNECTION UTILIZING WEB BROSWER
3.1. Recommended PC specification for web browser connections
Requirements below apply to connection with an IP camera, assuming smooth image display in
1600x1200 resolution and 25 fps speed.
1. CPU Intel Pentium IV 3 GHz or newer
2. RAM Memory min. 512 MB
3. VGA card (any displaying Direct 3D with min. 128 MB RAM memory)
4. OS Windows XP / VISTA
5. Direct X version .0 or newer
6. Network card 10/100/1000 Mb/s
3.2. Connection with IP camera via the Internet Explorer
You have to enter camera IP address in the Internet Explorer address bar. If IP address is correct user
login window will be displayed:
Default user is root and default password is pass.
For safety reasons, it is recommended to change default user name and password.
NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0
All rights reserved © AAT Holding sp. z o.o.
13
When you log on to the camera, web browser will download the applet for displaying images from the
camera. Depending on the current Internet Explorer security settings it may be necessary to accept
an ActiveX control. To do this, click the right mouse button on the message, select "Install Active X
control" and then click Install.
If the installation fails, changing security settings for the IE browser is required. In order to do that,
please choose: Tools > Internet options > Security tab > Custom level and:
• Under Download unsigned ActiveX controls - select either Enable or Prompt
• Under Initialize and script ActiveX controls not marked as safe - select Enable or Prompt
You can also add the camera’s IP address to “trusted zone and set lowest security level for it.
In addition, when working in Windows Vista the ActiveX applet may be blocked by Windows
Defender. In such case you should allow to run this applet, or simply disable the Windows Defender.
NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
14
3.3. Connection with IP camera via the Mozilla Firefox
It is also possible to connect to the camera by using Mozilla Firefox, but this browser doesn't offer full
functionality of the camera, so the recommended browser is Internet Explorer. The first run of the
IP camera in Firefox is very similar like in the IE. After you type the correct IP address you have to
write correct username and password. The default user is root and password is pass. Next, you will be
prompted to install the missing plug-in. You must be logged as administrator to install the plug-in
correctly. Then you have to follow the instruction below:
Click this link
Choose save file
Double click
Select OK
NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0
All rights reserved © AAT Holding sp. z o.o.
15
Select Run
A window depicting installation of particular components is then displayed. After proper installation
pictures from the camera should become visible
NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
16
4. WWW INTERFACE – WORKING WITH IP CAMERA
4.1. Displaying live pictures.
1. View size selection
2. Stream selection (if available)
3. Outputs - activate or deactivate alarm output of camera (if available)
4. Visitors online - information about number of connected viewers
5. Activate speakers - enables sending audio from PC to camera audio output (if available)
6. Snapshot - saves current frame in JPEG format
7. Setup - camera configuration
8. Alarm - information about alarm input triggered by motion detection
9. OSD - default OSD display containing time and date
WWW INTERFACE - WORKING WITH IP CAMERA
6.Snapshot
7.Setup
5.Speaker
4.Online
connection
3.Outputs
9.Alarm 8. OSD.
2. Stream selection
1.View size

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0
All rights reserved © AAT Holding sp. z o.o.
17
Right mouse button click on the live screen view allows to use the following functions:
1.Snapshot - saves the current frame in JPEG format
2.Record start record stop - starts or stops local disc video recording (including audio)
3.Mute - disables sound from camera (if available)
4.Full screen - switches to live view mode in full screen
Full screen mode is also enabled after double-clicking on screen.
5.Digital zoom - Launch digital zoom function
After enabling digital zoom, window for navigating digital zoom is displayed.
Please click the Enable digital zoom first, next choose zoom factors and select desired place on the
screen to zoom in. Green rectangle indicates selected part of picture.
4.2. Camera configuration
After clicking Setup button web page switches to configuration mode. On the left hand side you can see
a list of camera parameters.
System - System settings
Network - Network settings
A/V setting - Audio and video settings
Event setting - Event and action settings
To get back to live view mode you have to click Live button in bottom-right corner of screen.
WWW INTERFACE - WORKING WITH IP CAMERA

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
18
WWW INTERFACE - WORKING WITH IP CAMERA
4.2.1. System settings
a. System information - Set up the camera name, select language, and set up the camera time.
• Camera model - information about camera model
• MAC Address - MAC address of a device
• Name-allows to enter server's description displayed both in the title bar and NMS software
• Language - changes OSD language
• Time stamp - enables or disables time and date on live view
• OSD position - sets the dime date displaying position.
• Text - text description on camera live view
• Date format- selects date display mode
• Time zone - selects local time zone
• Enable daylight saving - ticking allows to set the dates of switching between standard summer time
• NTP: Server - domain or IP address of an NTP server
• NTP: Update - sets frequency of time update
• NTP: Time shift - shifts time to local
• Synchronize with PC time - synchronizes time and date with the PC clock
• Manual - sets up a specific date and time (user-defined)
• The time and date remain the same - disables time adjustment

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0
All rights reserved © AAT Holding sp. z o.o.
19
b. User management - tab responsible for adjusting user parameters, add new ones or delete existing.
• Anonymous user login - allows anyone to watch live camera view.
• Add user - adds new user (guest). To add an account, please type in the user name and password,
then click “Add Set”.
• User list - Displays list of users. Changing a password or deletion of a user is possible here.
Click EDIT to modify the user name and password, as depicted below.
To remove user, please click REMOVE and confirm by clicking OK. Deleting Administrator account is
impossible. Up to 20 users are available.
WWW INTERFACE - WORKING WITH IP CAMERA

NVIP-TDN3401H/IR/MPX2.0
User’s manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
20
WWW INTERFACE - WORKING WITH IP CAMERA
c. System update - tab responsible for upgrading firmware, saving and restoring default camera
settings.
• Firmware upgrade - Upgrades the camera with a new firmware.
To update firmware online, please click the BROWSE button and then select new f w file (.bin
extension). Next, click UPGRADE and confirm with OK to proceed.
Caution:
Please contact your local distributor prior to software upgrade.
Caution:
You should close all other programs and access only single camera in the Internet Explorer
browser at once. Power failure or turning off the device while upgrading the software results in
camera damage and necessity for service repair.
• Reboot system - pressing the START button restarts camera
• Factory default - pressing the START button restores default settings ( except the IP address)
• Setting management - allows to export settings directly to a PC, or upgrade from previous using
saved settings.