Novus NVC-150B User manual

USER`S MANUAL VER. 1.0
B/W CAMERA
NVC-150B
NOVUS SECURITY Sp. z o.o.
359 Pulawska Str., 02-801 Warsaw, Poland
tel: [phone]; fax: [phone]
[email protected]; www.novuscctv.com
© Copyright 2003, NOVUS SECURITY Sp. z o.o.

NVC-150B B/W camera, User’s Manual
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved.
2
B/W CCD CAMERA
Operating Instructions
CAUTION
1. Please use correct power adaptor, AC230V (regulated), to operate this unit. The power tolerance of
this unit is AC 230V ± 10% (AC207V~253V), over maximum AC253V power input will damage this
unit.
2. Video output (BNC connector) of this unit can be only connected to monitor. Please check the
wiring of video output before power on. If the power is offered through video output, the unit will be
damaged.
1. Do zasilania kamery należy użyćwłaściwego zasilacza prądu stałego : AC230V (regulowane).
Tolerancja napięcia dla tej kamery wynosi: 230 VAC ± 10 % (207 -253 VAC).Przyłożenie do kamery
napięcia większego od dopuszczalnego tj. powyżej 253 VAC, może spowodowaćuszkodzenie kamery.
2. Wyjście wizyjne kamery (BNC) można połączyćwyłącznie z właściwymi wejściami urządzeńCCTV
Przed połączeniem kamery z innymi urządzeniami CCTV należy sprawdzićokablowanie. Jeśli wraz z
wizjązostanie podany inny sygnał, o napięciu większym niż1 V p-p, kamera może ulec uszkodzeniu.
1. Por favor use el correcto adaptador de energía eléctrica AC230V (regulado) para operar esta
unidad, La tolerancia de energía de esta unidad es de AC230V ± 10% (AC207V~253V). Sobrepasar el
máximo de AC253V de la potencia de entrada dañara esta unidad.
2. La potencia de salida del video (Conector BNC) de esta unidad puede solo ser conectado al
monitor. Por favor revise los cables del video antes de encenderlo. Si la energía es dada por la
potencia de salida del video, la unidad se dañara.
1. Bitte schließen Sie das Gerät an das Netzgerät (AC230V) an. Die Toleraz der Stromversorgung ist
230V AC ± 10% (AC207V~253V). Abweichende Werte können zu Beschädigungen am Gerät führen.
2. Verbinden Sie den Video-Ausgang (BNC-Anschluß) mit dem Video-Eingang des Monitors. Bevor
Sie die Spannungsversorgung einschalten, überprüfen Sie Bitte den korrekten Anschluß des Video-
Ausgangs. Falsche Anschlußbelegungen können zu Beschädigungen an den Geräten führen.

NVC-150B B/W camera, User’s Manual
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved.
3
Thank you for choosing this high quality camera. Before operating the camera, please read
following instructions completely and carefully.
PRECAUTIONS
• Do not install the camera in extreme temperature condition.
• Do not install the camera in an environment where the humidity is high.
• Do not install the camera under the unstable lighting condition.
• Do not disassemble the camera.
• Do not expose the camera to rain or moisture.
• Do not keep the camera face to strong light directly.
• Do not touch the front glass of the camera.
• Do not use other than specified power source.
FEATURES
• Horizontal Resolution of 380 TV Lines.
• Minimum Illumination 0.09 Lux at F1.2.
• S/N Ratio is more than 48dB (AGC off).
• Built-in Auto Electronic Shutter.
• V.D./D.D. selectable
SPECIFICATIONS
Pick up Element 1/3" Samsung B/W CCD image sensor
Number of Pixel 510(H) x 492(V) <EIA> / 500(H) x 582(V) <CCIR>
Resolution 380 TV lines
Min. Illumination 0.09 Lux at F1.2.
S/N Ratio More than 48dB (AGC off)
Electronic Shutter 1/60 (1/50) to 1/100,000 sec
Iris Mode V.D. / D.D. selectable
Video Output 1.0Vp-p composite,75 Ohm
Lens Mount C/CS mount changeable
Microphone Yes
Power Source AC230V ± 10%
Fuse 0.16A
Power Consumption 3W
Dimension (mm) 118(L) x 62(W) x 50(H)
Weight 510 g
* Design and specifications are subject to change without notice.

NVC-150B B/W camera, User`s Manual
4
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD,DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
1. Flange Back Adjustment Ring
Suitable for CS-mount lens, When use C-mount lens, please use the CS-C conversion Ring.
2. Back focal lock screw
The camera is set at the standard back focal position . Depending on types of lenses, however slight
adjustment may be necessary. Adjust the lens back-focus by turning the focusing knob.
Major Operating Control and Functions
AUTO IRIS
AC 230V
AES
2
LEVEL
PL
HL
4
1
AI
3
V.D.
VIDEO
D.D.
AUDIO
AC 230V
PL
AUTO IRIS
24
AI
L H
LEVEL
AES
13
VIDEO
D.D.V.D.
AUDIO
Major Operating Control and Functions
Major Operating Control and Functions

NVC-150B B/W cameraUser’s Manual
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved.
5
3. Auto iris Lens Connector
Use for connecting auto iris lens plug. For details, see connection.
4. DC Level Adjustment V.R.
Use for adjusting video output level of DC drive auto iris lens.
5. Power LED Indicator
The Power LED Indicator indicates normal during operation.
6. Power Input Terminal
This terminal is for connecting the 230V AC regulated power supply.
7. Video Output Connector (VIDEO OUT)
This connector is for connecting with the VIDEO IN connector of the video monitor.
8. AES/AI Selector
Lets you select the mode according to the lens type that is used with this camera.
AES: Select this mode when a fixed iris lens or manual iris lens is used with this camera.
AI: Select this mode when an auto iris lens is used with this camera.
9. IRIS V.D./D.D. Selector
Lets you select the mode according to the lens type that is used with this camera.
V.D.：Select this mode when a VIDEO Drive auto iris lens is used with this camera.
D.D.：Select this mode when a Direct Drive auto iris lens is used with this camera.
10. Audio Output Connector (AUDIO OUT)
This connector is for connecting with the AUDIO IN connector of the video monitor.
CONNECTIONS
1. Mount a lens onto the camera.
2. Set the lens selection switch (AES/AI).
3. Connect a video terminal of the camera (VIDEO) and the video input terminal of the video monitor
with a 75 Ohm coaxial cable.
4. Connect a audio terminal of the camera (AUDIO) and the audio input terminal of the video monitor.
5. Connect the power terminal of the camera to a 230V AC regulated power supply.

NVC-150B B/W cameraUser’s Manual
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved.
6
Installation of Auto Iris Lens Connector
Install the lens connector when using a Video drive lens.
The installation should be made by qualified service personnel or system installers
Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and
then remove the outer cable cover of the supplied connector as shown in the diagram .
The pin assignment of the auto iris lens connector is as follows:
VIDEO DC
Pin 1 Power source Damp -
Pin 2 Video signal Damp +
Pin 3 Not used Driver +
Pin 4 Ground, Shield Driver -
Solder the lens cable to the pins of the supplied connector
Focus or Flange-Back Adjustment
The following adjustment should be made by qualified service personnel or system installers.
1. Mount the lens by turning it clockwise on the lens mount of the camera.
2. Loosen the screws on the flange-back adjusting ring.
3. Turn the flange-back adjusting ring to the desired position.
4. Tighten the screws on the flange-back adjusting ring.
Standard Accessories
Main body and power cable *1
HEX wrench *1
C mount adaptor ring * 1
Iris header *1
Instruction manual *1

All rights reserved © NOVUS SECURITY
NOVUS SECURITY Sp. z o.o.