Novus NVC-DN6118SD/IR User manual

U s e r ’s m a n u a l
NVC-DN6118SD/IR
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
2
INFORMATION
EMC (2004/108/EC) and LVD (2006/95/EC ) Directives
CE Marking
Our products are manufactured to comply with requirements of following directives
and national regulations implementing the directives:
 Electromagnetic compatibility EMC 2004/108/EC.
 Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical
equipment designed for use with a voltage rating of between 50VAC and 1000VAC as
well as 75VDC and 1500VDC.
WEEE Directive 2002/96/EC
Information for users who want to get rid of electrical and electronic appliances
This product is marked according to the European Directive on Waste Electrical and
Electronic Equipment (2002/96/EC) and further amendments. By ensuring this product is
disposed of correctly, you will help to prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. The symbol on the product, or the documents accompanying the
product, indicates that this appliance may not be treated as household waste. It shall be handed
over to the applicable collection point for the waste electrical and electronic equipment for
recycling purpose. For more information about recycling of this product, please contact your
local authorities, your household waste disposal service or the shop where you purchased the
product.
RoHS Directive 2002/95/EC
Information concerning limitation of the use of dangerous substances in the
electrical and electronic appliances.
Out of concern for human health protection and friendly environment, we assure that our
products falling under RoHS Directive regulations, regarding the restriction of the use of
hazardous substances in electrical and electronic equipment, have been designed and
manufactured in compliance with the above mentioned regulation. Simultaneously, we
claim that our products have been tested and do not contain hazardous substances whose
exceeding limits could have negative impact on human health or natural environment.
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed
for self installation in households by individuals without technical knowledge.
The manufacturer is not responsible for defects and damages resulted from improper or inconsistent
with user’s manual installation of the device in the system.
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
3
OSTRZEŻENIA
IMPORTANT SAFEGUARDS AND WARNINGS
ATTENTION!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT PROVISIONED FOR THE
GIVEN PRODUCT IN ITS USER’S MANUAL AND OTHER DOCUMENTS DELIVERED
WITH THE PRODUCT, OR THAT ARISES FROM THE NORMAL APPLICATION OF THE
PRODUCT, ITS MANUFACTURER MUST BE CONTACTED OR THE RESPONSIBILITY
OF THE MANUFACTURER FOR THE RESULTS OF SUCH AN ACTION SHELL BE
EXCLUDED.
IMPORTANT SAFEGUARDS AND WARNINGS
1. Prior to undertaking any action with the device, please consult following manual, and read all the
safety and operating instructions before operating the device.
2. Please keep the following manual for the time of device’s lifespan in case when referring to the
contents of the manual would become necessary.
3. Follow all the safety precautions described in this manual. Improper installation and camera
operation may have impact on operator safety as well as camera operational reliability and lifespan.
4. Camera mounting and operations should be conducted according to this manual, both for users and
service personnel.
5. Please unplug the unit from the power before starting maintenance procedures.
6. Please use only attachments / accessories specified by the manufacturer.
7. Do not install the camera near any steam sources or near water (any wet area like pools, bath tubs
etc.).
8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)
is not recommended since it may lead to heat build-up and damaging the device itself in
consequence.
9. Mounting the camera on unstable surface or using not recommended mounts is forbidden.
Improperly mounted camera may be the cause of fatal accident or be seriously damaged itself.
Camera must be mounted by qualified personnel with proper authorization, in accordance to user’s
manual.
10.Device should be supplied only from power sources which parameters are in accordance to one’s
pointed out by the producer in camera technical datasheet. Therefore it is forbidden to supply the
camera from power sources with their parameters unknown, unstable or not meeting the producer’s
requirements.
11.Signal cables (conducting TV or/and telemetric signal) should be placed in a way excluding the
possibility of damaging them by accident. Special attention must be paid to cables going out of the
camera and connecting power supply;
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
4
OSTRZEŻENIA
IMPORTANT SAFEGUARDS AND WARNINGS
12.To avoid equipment damage, whole TV circuit should be equipped with properly made
(in accordance with Polish Regulations) discharge-, overload- and lightning protection devices.
Usage of separating transformers is advised.
13.Electric installation supplying the device should be designed to meet the specifications given by the
producer in such a way, that overloading it is impossible.
14. Camera should be protected from water and objects that may get inside it.
15. User cannot repair or upgrade equipment himself. All maintenance actions and repairs should
be done only by the qualified service personnel.
16. Unplug the camera from the power source immediately and contact the proper maintenance
department when the following occurs:
 Damages to the power cord or to the plug itself;
 Liquids getting inside the device or exposure to strong mechanical shock;
 Device behaves in a way not described in the manual and all adjustments approved by the
manufacturer, and possible to apply by user himself, seem not to have any effect;
 Camera is damaged;
 Atypical behaviour of the camera components may be seen (heard).
17. In case of repairs please pay attention to using only original replacement parts (with their
parameters in accordance to those specified by the producer) should be paid. Non-licensed service
and non-genuine replacement parts may cause fire or electrocution;
18. After maintenance procedures please conduct device tests and make sure that all the camera
components are operating correctly.
19. Device may be supplied only from 12 VAC power supply. Power output should equal at least 36 W
for each camera.
INFORMATION
Data included in the following user’s manual is up to date at the time of printing.
AAT Holding Sp z o.o. holds exclusive rights to modify this manual. The producer reserves the rights
for device specification modification and change in the design without prior notice.
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
5
1. PACKAGE CONTENTS
If any of the listed equipment has been damaged during transport or if the package is incomplete, the
contents of package should be packed back to the original box. Contact the local NOVUS distributor
for further assistance.
2. MAIN CHARACTERISTICS
 Day/Night PTZ cameras
 Mechanical IR cut filter
 IR operation capability
 Horizontal resolution: up to 650 TVL
 Min. illumination: from 0.001 lx/F=1.2 (0 lx –IR On)
 Motor-zoom lens, AI and AF function
 Inteligent IR Illuminator
 7 tours
 1 scan
 6 patterns
 175 presets
 18x optical zoom
 Home function
 Auto-flip - automatic 180° camera rotation after reaching tilt limit.
 Global function
 Password protected menu
 Full configuration (user friendly multi-lingual OSD):
- from the NV-KBD70, NV-KBD50 keyboards
- directly from the front panel of selected NOVUS® DVRs
 Features pan, tilt and zoom control via NV-KBD70, NV-KBD50 keyboards and directly via
front panels of certain NOVUS® DVRs
 RS-485 control
 N-Control, Pelco-P, Pelco-D remote control protocols
 IP 66
 Wall mount bracket in-set
 Power supply: 12 VDC
FOREWORD INFORMATION
Speeddome
camera
User’s manual ScrewsWall mount
bracket
Power supply
12VDC
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
6
3. TECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION
NVC-DN6118SD/IR
IMAGE
Pick-up element CCD imager, 1/3” SONY EXview HAD II
Number of Effective Pixels 960 (H) x 582 (V)
Horizontal Resolution 650 TVL - color mode, 650 TVL - B/W mode
Min. Illumination 0.01 lx/F=1.2 - color mode (1/50 s),
0.001 lx/F=1.2 - B/W mode
0lx (IR on) - B/W mode
Electronic Shutter Automatic: 1/30 s ~ 1/10 000 s
LENS
Zoom 18x optical
Type Motor-Zoom AF/ AI lens,
f=5 ~ 90 mm/F=1.6 ~ 3.0
Angle of View (H) 48° ~ 5°
DAY/NIGHT
Type Mechanical IR cut filter
Switching Mode Automatic / Manual
PTZ
Presets 175
Tours 7 (up to 16 function per tour)
Scans 1
Patterns 6 (up to 2 min per pattern)
Tilt / Pan 0° ~ 90°/ 360° (continuous rotation)
Tilt / Pan Speed Up to 240°/s (proportional to zoom)
Protocols N-Control, Pelco-D, Pelco-P
ADDITIONAL FUNCTIONS
Camera OSD English, Polish, Russian
Password Protection 6 characters (letters and numbers)
Back light compensation (BLC) Yes
Effects Mirror
IR LED
Number 8 High Power LED
Range 100m
Angle up to 30° (proportional to zoom)
INTERFACES
Video output BNC, 1.0 Vp-p, 75 Ohm
RS-485 Yes
INSTALLATION PARAMETERS
Dimensions (mm) 197 (Ø) x 340 (H)
With mounting bracket: 339 (W) x 353 (H)
Weight 4,6 kg
With mounting bracket: 5,5 kg
Enclosure Aluminium, white
Wall mounting bracket in-set
Power supply 12 VDC
Power consumption 8W
36 W (IR on)
Operating temperature -30°C ~ 55°C
Degree of protection IP 66
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
7
3.1. Camera dimensions
All dimenstions in mm.
TECHNICAL SPECIFICATION
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
8
3.2. View of the camera, layout of the camera items
4. MOUNTING THE CAMERA
In order to obtain declared watertightness camera should be mounted on flat, smooth surfaces.
When mounting the camera on uneven/rough surfaces please seal the mounting place additionally
with appropriate sealing mass, paying special attention to mounting holes.
Caution!
Due to safety reasons, maximum load capacity of surface shouldn’t be less than 25kg.
In order to successfully mount a camera, please follow the procedure below:
 Put the bracket to the wall in a desired mounting place (with cable hole). Taking the bracket’s
base screw holes (1) as a pattern, mark future drilling holes for screws using a punch.
 Drill 4 holes in accordance with previously done markings and base hole placement (when
mounting the camera to concrete surfaces please purchase appropriate mounting accessories)
 Put required cables through the bracket arm.
 Mount the bracket with seal, paying special attention to all mounting holes and additionally
sealing them with appropriate sealing mass if necessary.
 Put the mounting of the camera module (2) in the bracket socket (3)
MOUNTING THE CAMERA
Camera module
Light sensor
IR Illuminator
Wall mount bracket
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
9
 Tight three screws (4) holding the camera module and bracket.
 Please make sure the cable goes throughout the passage (5), and screw the bracket to the
wall.
 All conections of power supply and video cables should be done in junction box.
CAUTION!
The supply voltage should be turned on when camera unit is completely installed. Otherwise,
enter camera’s menu and reboot it after finishing installation.
5. START-UP AND INITIAL CONFIGURATION
5.1 Connections
Warning: Device should be supplied only from power sources whose parameters are
in accordance with those specified by the producer in the technical datasheet of the
camera. Therefore, it is forbidden to supply the camera from power sources with
their parameters unknown, unstable or not meeting the producer’s requirements.
START-UP AND INITIAL CONFIGURATION
1
1
2
3 4
4
5
Video
Power supply 12V DC +/- 10%
Video
GND
+
- (GND)
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
10
5.2. RS485
For camera and controller communication, RS-485 link is used. CAT5 unshielded twisted pair cable is
recommended for telemetry data transmission. Only one wire pair of CAT5 0.35 mm² cable is used for
controlling the camera and maximum allowed distance for RS-485 communication between camera
and keyboard is 1.200 m.
For RS-485 connections, RS485+ and RS485–wires should be used. They should be connected
to respective TX+ and TX–connectors of the controller, e.g. NV-KBD70 keyboard. Next camera in
the cascade is connected also using same RS485+ and RS485–connectors.
When conecting telemetry cables into a star a serial data distributor should be used, e.g. NOVUS
NVRS-016DD.
START-UP AND INITIAL CONFIGURATION
Wire color Description
Orange RS485+
Yellow RS485-
Yellow/green GND
Yellow/green GND
PTZ
CONTROLLER
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
11
5.3. Camera DIP switch settings
Camera features DIP-switch blocks for configuring addresses and transmission parameters for RS-485
protocol. Switches are located under the cover located underneath camera module.
Camera address Protocol and speed settings
 Addressing the camera
In order to avoid control conflicts, each camera should be assigned with unique address in the system.
Switches numbered 1 to 8 are responsible for assigning an address.
When building a system containing a single DVR, assign addresses in accordance with their respective
video inputs numbering.
Number visible on the DIP switch and their values are described in table below. Sum of the values
determines the physical ID address of the camera.
ATTENTION!
Each camera has its address set to 1 by default!
START-UP AND INITIAL CONFIGURATION
Switch no: 1 2 3 4 5 6 7 8
Value: 1 2 4 8 16 32 64 128
1 ON OFF OFF OFF OFF OFF OFF OFF
2 OFF ON OFF OFF OFF OFF OFF OFF
3 ON ON OFF OFF OFF OFF OFF OFF
5 ON OFF ON OFF OFF OFF OFF OFF
11 ON ON OFF ON OFF OFF OFF OFF
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
12
Except the hardware address (sets by DIP switch), camera allows to set software address.
Additional descritpion is in chapter 7.4 Menu System, Address function.
 Selecting protocol parameters
Switches 1 and 2 are related with protocol selection. Table below depicts available switch
configurations:
 Selecting transmission speed
Switches 3 and 4 are related with transmission speed. Table below depicts available switch
configurations:
Please pay attention to setting identical transmission parameters for controllers (keyboard, DVR, PC).
START-UP AND INITIAL CONFIGURATION
Transmission speed
Switch no
3 4
2400 bps OFF OFF
4800 bps ON OFF
9600 bps OFF ON
19200 bps ON ON
Protocol
Switch no
1 2
PELCO-D, PELCO-P OFF OFF
N-Control OFF ON
others ON OFF
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
13
6. CONTROLLING THE CAMERA
N-Control is the recommended control protocol for the Novus PTZ cameras and allows to fully utilise
their abilities. Cameras may be also PELCO-D/PELCO-P controlled, however methods of
programming and control differ.
To establish proper connection between camera and keyboard following conditions must be met:
 an unique camera address for the whole system
 the same baud rate (speed setting) in the camera and in the keyboard (2400/4800/9600/19200)
Details regarding camera control settings are described in proper manual of the keyboard.
6.1. Controlling the camera via the N-Control
In NV-KBD50 functions depend on button pushing method:
- Push the button;
- Push the button and hold for three seconds;
In order to start camera control please enter its number via numpad and confirm with (for
NV-KBD50 keyboard) or (for NV-KBD70) key.
To open camera menu please press (3s) (for NV-KBD50) or (for NV-KBD70).
Navigation through camera’s OSD menu:
CONTROLLING THE CAMERA
Action Function
Joystick up or down Navigation through menu
Joystick left or right
Navigation through text fields
Editing field value
Changing parameter values
Iris OPEN Execution of a command
Editing field value
Iris CLOSE Save and return to a higher-level menu
focus control - far Cancelling a command
CAM
(3s)
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
14
CONTROLLING THE CAMERA
Functions of particular buttons for NV-KBD50 and NVKBD70 are presented below:
In order to call a surveillance function, please select its number from the numpad and confirm it by
pressing appropriate function button (e.g. [PRESET])
Manual
description NV-KDB70 NV-KBD50 Function
IRIS OPEN
iris control - opening, password entering,
start of programming
IRIS CLOSE iris control - closing, end of programming
FOCUS FAR
focus control - far
FOCUS NEAR focus control - near
PRESET MOVE preset calling
GLOBAL
PRESET MOVE preset calling for all connected cameras
PRESET SET (3s) preset saving
SCAN auto-scan
SCAN SET (3s) auto-scan programming
TOUR tour function
TOUR SET (3s) tour programming
PATTERN pattern function
PATTERN SET (3s) pattern programming
MENU (3s) opens OSD menu, confirms selection
ON enables additional functions
OFF disables additional functions
HOME returns camera to home position
ENTER
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
15
CONTROLLING THE CAMERA
Using two buttons listed below is necessary in order to program surveillance functions. Please select
appropriate number and, holding mentioned button, press the second one (e.g. hold [CTRL] and press
[TOUR] )
Additional functions are enabled/disabled via ON / OFF buttons
Additional functions are presented in the table below:
Function number Function
1 Enables/disables relay 1
7 Selects Auto / Manual focus mode
8 Selects Auto / Manual AE mode
9 Changes night shot to auto
10 Turns on / turn off infrared filter
11 Turns on / turn off back light compensation
12 Turns digital zoom on / off
13 Turn camera status information on / off
104 Turn wide dynamic range on / off
105 Turn picture stabilization on / off
NV-KBD70
Keyboard
NV-KBD40
Keyboard Function
Turning on additional functions. List of additional functions
is described below. To turn on a demanded function, select
its number using numerical keys and press or
Turning off additional functions. List of additional functions
is described below. To turn off an additional function, select
its number using numerical keys and press or
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
16
6.2. Controlling the camera via PELCO-D / PELCO-P protocols
Controlling the camera via PELCO-D/PELCO-P protocols is also possible, however methods
of programming differ. Furthermore PELCO doesn’t support all camera functions in contrast
to N-CONTROL.
In NV-KBD50 functions depend on button pushing method:
- Push the button;
- Push the button and hold for three seconds;
In order to start camera control please enter its number via numpad and confirm with ( f o r
NV-KBD50 keyboard) or (for NV-KBD70) key.
To open camera menu please press (3s) (for NV-KBD50) or (for NV-KBD70).
Navigation through camera’s OSD menu:
INFORMATION:
Opening the camera MENU may be also performed via calling preset 95 by pressing 95 and PRESET
MOVE or PRESET SET.
CONTROLLING THE CAMERA
Action Function
Joystick up or down Navigation through menu
Joystick left or right
Navigation through text fields
Editing field value
Changing parameter values
Iris OPEN Execution of a command
Editing field value
Iris CLOSE Cancelling a command
Return to a higher-level menu
CAM
(3s)
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
17
CONTROLLING THE CAMERA
Type FunkcjaNr.
PRESET MOVE/SET Enables/disables relay 1161
PRESET MOVE/SET Enables/disables zoom proportional function167
PRESET MOVE Turn wide dynamic range off170
PRESET MOVE Turn wide dynamic range on171
PRESET MOVE Changes focus mode to auto174
PRESET MOVE Changes focus mode to manual175
PRESET MOVE Changes focus mode to semiauto176
PRESET MOVE Changes night shot to auto mode177
PRESET MOVE Changes night shot to night mode178
PRESET MOVE Changes night shot to day mode179
Oznaczenie
w instrukcji
Klawiatura
NV-KDB70
Klawiatura
NV-KBD50 Funkcja
IRIS OPEN
iris control - opening
IRIS CLOSE iris control - closing
FOCUS FAR
focus control - far
FOCUS NEAR focus control - near
PRESET MOVE preset calling
PRESET SET (3s) preset saving
SCAN
11 - 18
141 -148
11 - 18
141 - 148
auto scan function
TOUR
21 - 28
151 - 158
21 - 28
151 - 158
tour function
PATTERN
1 - 4
131 -134
1 - 4
131 - 134
pattern function
MENU (3s) entering camera menu
Additional functions are presented in the table below:
Functions for the NOVUS NV-KBD50 and NVKBD70 are presented in the table below:
To call an observation function (pattern, preset) please select its function number first (using numpad),
then confirm it by function call button (e.g. [PRST]). To start AUTOSCAN or TOUR function please
select its function number from the given range and acknowledge preset calling key.
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
18
7. CAMERA OSD MENU
Before programming or operating the PTZ camera, you have to select a desired camera number (via
keyboard or another remote controller).
Accessing the camera’s menu depends on the controller type and the protocol used.
All the details regarding camera communication parameters are described in the instruction manuals of
the NV-KBD50/70 keyboards (or other controllers).
Menu is accessible after pressing the (3s) button, ESC closes the menu. When additional
functions (such as tour or auto-scan) are programmed or when camera is in alarm mode, menu is
accessible only after abandoning current mode (e.g. by forcing the tilt or pan movement or by
confirming alarm).
ATTENTION!
Default language is set to English. To change the language in main menu choose the 7. Language,
move joystick right / left and select requested language.
Main menu is depicted below:
Exemplary submenu for editing the name or number is shown below:
Move joystick left /right to indicate the position for editing, then press OPEN. It display the screen:
Select desired character or number, and press OPEN to enter this character at desired possition.
CAMERA OSD MENU
MAIN MENU
1 PTZ Functions
2 Display Settings
3 Control Settings
4 Camera Settings
5 System Settings
6 Password
7 Language English
Press Close to Exit
_ _ _ _ _ _ _ _ _ _ _
↑
Press Close to Exit
0123456789ABCDEFGHIJKLMN
↑
OPRSTUVWXYZ
Press OPEN to confirm
Press Close to Exit
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
19
Character will be saved. CLOSE saving the name and get back to the menu.
7.1. PTZ FUNCTIONS menu
This menu contain settings related with PTZ functions of the camera. They are listed below.
7.1.1. PRESET submenu
Menu contain settings of programmable presets. Programmed presets may be called directly from the
keyboard, used in pattern function or used as a default action for home/alarm functions.
NUMBER- selects the preset number for editing or run.
SET PRESET- allows to set the desired scene, then save it as the preset.
CALL PRESET- moves the camera to selected preset.
DELETE PRESET - deletes the selected preset from camera memory.
NAME - allows to create the particular names for each preset f.e. „CORRIDOR1”, „ROOM2”.
They are displayed on the screen after calling the preset.
NAME DISPLAY ON/OFF - turn on/off the name displaying on the screen.
CAMERA OSD MENU
_ A _ _ _ _ _ _ _ _ _
Press CLOSE to Exit
PTZ Functions
1 Preset
2 Pattern
3 Tour
4 Scan
5 Auto Pan
6 Home Function
Press CLOSE to Exit
Preset
1 Number 1
2 Set Preset
3 Call Preset
4 Delete Preset
5 Name _______________
6 Name Display ON/OFF
Press CLOSE to Exit
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR

NVC-DN6118SD/IR User’s manual, ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
20
CAMERA OSD MENU
7.1.2. PATTERN submenu
Pattern is a sequence of an existing functions (pan, turn, zoom, etc.), that may be called via keyboard or
used in tours. Camera allows for saving 6 patterns. Maximum length is 2 minutes per pattern.
NUMBER- selects the pattern number for editing or run.
PROGRAM- run the programming the pattern. Press OPEN to start saving the joystick
movement. CLOSE to save .
RUN- starts the selected pattern.
DELETE - deletes the selected pattern from camera memory.
NAME - allows to create the particular names for each pattern f.e. „CORRIDOR1”, „ROOM2”.
They are displayed on the screen during the pattern.
NAME DISPLAY ON/OFF - turn on/off the name displaying on the screen.
7.1.3. TOUR submenu
Allows to set up Tours, i.e. lists of consecutively executed surveillance functions (presets, patterns, and
scans, up to 16 functions per tour). During tour, camera stops at presets for a defined period of time,
while scans/patterns are repeated certain amount of times.
Pattern
1 Number 1
2 Program
3 Run
4 Delete
5 Name _______________
6 Name Display ON/OFF
Press CLOSE to Exit
Tour
1 Number 1
2 Program
3 Run
4 Delete
Press CLOSE to Exit
http://www.e-camere.ro/camere-supraveghere/Novus/NVC-DN6118SD-IR