Novus NVC-GDN4801V/H-2 User manual

NVC-GDN4801V/H-2
NVC-GDN4801V-2
NVC-GDN4801V/IR-2
NVC-GDN4801V/IRH-2
u s e r ’s m a n u a l

NVC-GDN4801V/H-2, NVC-GDN4801V-2, NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2
1.3 version - User’s manua
A rights reserved © AAT Ho ding sp. z o.o.
2
EMC (2004/108/EC) and LVD (2006/95/EC ) Directives
CE Marking
Our products are manufactured to comply with the requirements of the following directives and national
regulations implementing the directives:
• Electromagnetic compatibility EMC 2004/108/EC.
• Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical
equipment designed for use with a voltage rating of between 50VAC and as well as 75VDC and
1500VDC.
WEEE Directive 2002/96/EC
Information on Disposal for Users of Waste Electrical and Electronic Equipment
This appliance is marked according to the European 1000VAC Directive on Waste Electrical and
Electronic Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of
correctly, you will help to prevent potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product.
The symbol on the product, or the documents accompanying the product, indicates that this appliance
may not be treated as household waste. It shall be handed over to the applicable collection point for used
up electrical and electronic equipment for recycling purpose. For more information about recycling of this
product, please contact your local authorities, your household waste disposal service or the shop where
you purchased the product.
RoHS Directive 2002/95/EC
Out of concern for human health protection and friendly environment, we assure that our products
falling under RoHS Directive regulations, regarding the restriction of the use of hazardous substances
in electrical and electronic equipment, have been designed and manufactured in compliance with the above
mentioned regulations. Simultaneously, we claim that our products have been tested and do not contain
hazardous substances whose exceeding limits could have negative impact on human health or natural
environment.
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed for self
installation in households by individuals without technical knowledge.
The manufacturer is not responsible for defects and damages that result from improper or inconsistent with
user’s manual installation of the device in the system.
INFORMATION

NVC-GDN4801V/H-2, NVC-GDN4801V-2, NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2
1.3 version - User’s manua
A rights reserved © AAT Ho ding sp. z o.o.
3
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A
PROPER DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE
YOURSELF WITH THE MANUAL PRIOR TO INSTALLATION AND FURTHER
DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO
USER-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE
PERSONNEL MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN
PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE
PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE
PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF
EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN
ACTION.
IMPORTANT SAFEGUARDS AND WARNINGS
1. Prior to undertaking any action please consult the following manual and read all the safety and
operating instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual
is necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a
direct influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the
user’s manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer
is forbidden;
7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers
etc.) is not recommended since it may lead to heat build-up and damaging the device itself
as a consequence;
8. Mounting the camera on unstable surface or using not recommended mounts is forbidden.
Improperly mounted camera may cause a fatal accident or may be seriously damaged itself. The
camera must be mounted by qualified personnel with proper authorization, in accordance with this
user’s manual;
SAFETY REQUIREMENTS

NVC-GDN4801V/H-2, NVC-GDN4801V-2, NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2
1.3 version - User’s manua
A rights reserved © AAT Ho ding sp. z o.o.
4
SAFETY REQUIREMENTS
9. Device should be supplied only from a power sources whose parameters are in accordance with
those specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply
the camera from a power sources with unknown parameters, unstable or not meeting producer’s
requirements;
10. Signal cables (conducting TV or / and telemetric signal) should be placed in a way excluding the
possibility of damaging them by accident. Special attention must be paid to cables getting from the
camera and connecting the power supply;
11. To avoid equipment damage, whole TV circuit should be equipped with properly made
discharge-, overload- and lightning protection devices. Usage of separating transformers is
advised;
12. Electric installation supplying the device should be designed to meet the specifications given
by the producer in such a way that overloading is impossible;
13. User cannot repair or upgrade the equipment himself. All maintenance actions and repairs should
be conducted only by qualified service personnel;
14. Unplug the camera from the power source immediately and contact the proper maintenance
department when the following occurs:
♦ Damages to the power cord or to the plug itself;
♦ Liquids getting inside the device or exposure to strong mechanical shock;
♦ Device behaves in a way not described in the manual and all adjustments approved by the
manufacturer and possible to apply by user himself, seem not to have any effect;
♦ Camera is damaged;
♦ Atypical behaviour of the camera components may be seen (heard).
16. In necessity of repairs attention to using only original replacement parts (with their parameters
in accordance with those specified by the producer) should be paid. Non-licensed service and
non-genuine replacement parts may cause fire or electrocution;
17. After maintenance activities tests should be run to ensure proper operation of all the functional
components of the device.
Attention!
Technical changes reserved without prior notice and printing errors possible.

NVC-GDN4801V/H-2, NVC-GDN4801V-2, NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2
1.3 version - User’s manua
A rights reserved © AAT Ho ding sp. z o.o.
5
1. PACKAGE CONTENTS
If any of the listed equipment has been damaged during transport or if the package is incomplete,
the contents of package should be packed back to the original box. Contact the local NOVUS
distributor for further assistance.
2. MAIN CHARACTERISTICS
• Mechanical IR cut filter
• IR operation capability
• Horizontal resolution: up to 700 TVL
• Min. Illumination: from 0.00003 lx/F=1.2 (DSS) (0 lx – IR On)
• Digital Slow Shutter (DSS)
• Auto iris DC lens: f=2.5 ~ 12 mm
• 3-axis camera module adjustment
• Digital zoom: 16x
• Wide dynamic range (SSDR)
• High Light Compensation (HLC)
• Digital Image Stabilizer (DIS)
• Digital Noise Reduction (DNR)
• Privacy zones: 12
• 1 alarm output triggered by motion detection
• Build in light sensor (NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2)
• Other functions: various picture effects, motion detection
• Full configuration (user friendly multi-lingual OSD):
- directly from the camera
- from the NV-KBD70, NV-KBD60 & NV-KBD40 keyboards
- from NOVUS
®
video capture cards
- directly from the front panel of selected NOVUS
®
DVRs
• Remote control: RS-485
• Protocols: PELCO-D, PELCO-P
• Built-in IR LED – 36 pcs (NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2)
• Built-in heater (NVC-GDN4801V/IRH-2, NVC-GDN4801V/H-2)
• IP 66
• Vandal proof housing
• Power supply: 12 VDC/24 VAC, 24 VAC
FOREWORD INFROMATION
Camera Screws with gaskets
4 pcs User’s manual
Cable for connecting
additional video output
Gasket Allen key

NVC-GDN4801V/H-2, NVC-GDN4801V-2, NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2
1.3 version - User’s manua
A rights reserved © AAT Ho ding sp. z o.o.
6
3. SPECIFICATION
FEATURES AND SPECIFICATION
Model NVC-GDN4801V-2 NVC-GDN4801V/H-2
Pick-up element 1/3” SONY SUPER HAD II CCD imager
Horizontal Resolution 600 TVL– color mode, 700 TVL– b/wmode
Min. Illumination
0.05 lx/F=1.2 – color mode (1/50 s),
0.005 lx/F=1.2 – b/w mode (1/50 s),
0.0001 lx/F=1.2 – DSS color mode,
0.00003 lx/F=1.2 – DSS b/w mode
S/N Ratio 52 dB (AGC off)
Electronic Shutter Auto: 1/50 s ~1/120 000 s
Digital Slow Shutter (DSS) 1/25 s ~ 10.24 s
Auto Gain Control (AGC) On/Off (2 levels)
White Balance 5 modes: Manual/AWC/Outdoor/Indoor/ATW
Wide dynamic range (SSDR) On/Off
Backlight Compensation (BLC) On/Off (3 modes)
High Light Compensation (HLC) On/Off
Synchronization Internal
Day/Night Switching Auto/Manual
Filter Delay 3 s/5 s/7 s/10 s/15 s/20 s/30 s/40 s/60 s
Flickerless Function On/Off
Privacy Zones 12
Lens Type Auto-iris DC: f=2.5 ~ 12 mm
Angle of View (H) 28° ~ 102°
Digital Zoom 16 x
IR LED -
IR Effective Range -
Camera Menu Multi-lingual On Screen Display (OSD)
Other Functions
Digital Image Stabilizer (DIS),
Digital Noise Reduction (DNR),
Motion detection,
Various picture effects: Mirror (horizontal) and 180˚ image rotation,
Image sharpness adjustment
Degree of Protection IP66
Casing Vandal-proof, aluminium alloy with poly-carbonate bubble
Video Output BNC, 1.0 Vp-p, 75 Ohm
Heter N/A Yes
Alarm Output 1, triggered by motion detection
Remote Control RS-485
Protocol Pelco-D, Pelco-P
Power Supply
Power Consumption 3 W 1.8 W, 4.2 W (Heater On)
OperatingTemperature -10°C ~ 50°C -40°C ~ 50°C
Dimensions (mm) 140 (Ø) x 103 (H)
Weight 930 g 940 g
12 VDC/24 VAC

NVC-GDN4801V/H-2, NVC-GDN4801V-2, NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2
1.3 version - User’s manua
A rights reserved © AAT Ho ding sp. z o.o.
7
FEATURES AND SPECIFICATION
Model NVC-GDN4801V/IR-2 NVC-GDN4801V/IRH-2
Pick-up element 1/3” SONY SUPER HAD II CCD imager
Horizontal Resolution 600 TVL– color mode, 700 TVL– b/wmode
Min. Illumination 0.05 lx/F=1.2 – color mode (1/50 s), 0.0001 lx/F=1.2 – DSS color mode,
0 lx (IR On)
S/N Ratio 52 dB (AGC off)
Electronic Shutter Auto: 1/50 s ~1/120 000 s
Digital Slow Shutter (DSS) 1/25 s ~ 10.24 s
Auto Gain Control (AGC) On/Off (2 levels)
White Balance 5 modes: Manual/AWC/Outdoor/Indoor/ATW
Backlight Compensation (BLC) On/Off (3 modes)
High Light Compensation (HLC) On/Off
Synchronization Internal
Day/Night Switching Auto/Manual
Filter Delay 3 s/5 s/7 s/10 s/15 s/20 s/30 s/40 s/60 s
Flickerless Function On/Off
Privacy Zones 12
Lens Type Auto-iris DC: f=2.5 ~ 12 mm
Angle of View (H) 28° ~ 102°
Digital Zoom 16 x
IR LED 36 pcs.
IR Effective Range Up to 35m
Camera Menu Multi-lingual On Screen Display (OSD)
Other Functions
Digital Image Stabilizer (DIS),
Digital Noise Reduction (DNR),
Motion detection,
Various picture effects: Mirror (horizontal) and 180˚ image rotation,
Image sharpness adjustment
Degree of Protection IP66
Casing Vandal-proof, aluminium alloy with poly-carbonate bubble
Video Output BNC, 1.0 Vp-p, 75 Ohm
Heater N/A Yes
Alarm Output 1, triggered by motion detection
Remote Control RS-485
Protocol Pelco-D, Pelco-P
Power Supply 12 VDC/24 VAC
Power Consumption 3 W, 6.W (IR On) 3 W, 5.2 W (Heater On), 9.6 W (Heter and IR On)
OperatingTemperature -10°C ~ 50°C -40°C ~ 50°C
Dimensions (mm) 140 (Ø) x 103 (H)
Weight 950 g 960 g
Wide Dynamic Range (SSDR) On/Off
24 VAC

NVC-GDN4801V/H-2, NVC-GDN4801V-2, NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2
1.3 version - User’s manua
A rights reserved © AAT Ho ding sp. z o.o.
8
3.1 Dimensions
3.2. View of the camera, layout of the camera items
NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2 models:
1 - joystick implementing UP, LEFT, RIGHT, DOWN, SET commands
2 - additional video output
3 - focus adjustment screw
4 - zoom adjustment screw
5 - heater (NVC-GDN4801V/H-2, NVC-GDN4801V/IRH-2)
6 - IR LED (NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2)
7 - Light sensor (NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2)
FEATURES AND SPECIFICATION
125
3
4
6 7

NVC-GDN4801V/H-2, NVC-GDN4801V-2, NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2
1.3 version - User’s manua
A rights reserved © AAT Ho ding sp. z o.o.
9
NVC-GDN4801V-2, NVC-GDN4801V/H-2 models:
1 - joystick implementing UP, LEFT, RIGHT, DOWN, SET commands
2 - additional video output
3 - focus adjustment screw
4 - zoom adjustment screw
5 - heater (NVC-GDN4801V/H-2, NVC-GDN4801V/IRH-2)
Camera module is placed on a mount allowing for 3-axis module position adjustment.
FEATURES AND SPECIFICATION
1 2
3
4
5
NVC-GDN4801V-2
NVC-GDN4801V/H-2
NVC-GDN4801V/IR-2
NVC-GDN4801V/IRH-2

NVC-GDN4801V/H-2, NVC-GDN4801V-2, NVC-GDN4801V/IR-2, NVC-GDN4801V/IRH-2
1.3 version - User’s manua
A rights reserved © AAT Ho ding sp. z o.o.
10
4. INSTALLATION
Prior to installation please familiarize yourself with the product, its parameters and installation
process.
To successfully install the camera please follow the steps presented below:
• Remove dome from the camera unscrewing three Allen screws located 120 degrees apart from
each other, using included Allen key.
• Put base of the camera to the desired mounting surface, and mark drilling holes using base as a
template.
• Drill mounting and cable holes in previously selected points.
• Paste the attached gasket to the base of the camera.
• Mount the camera using included screws with gaskets on smooth, even surface providing
declared degree of IP protection.
Warning: In order to provide the declared degree of IP protection, the camera should be mounted
only on smooth, even surfaces. When mounting to rough/uneven surfaces please seal the
mounting place additionally using appropriate sealing mass. When using a different
mounting kit (not included in the set) please pay special attention to sealing the mounting
holes with an appropriate sealing mass.
• Adjust the position of the camera module. If required, loosen the screw blocking camera
module.
• Unscrew the blocking screws and adjust focal length and focus. In NVC-GDN4801V/IR-2 and
NVC-GDN4801V/IRH-2 cameras take off lens cover containing IR LEDs first, by pressing two
latches, as depicted below:
• If needed, adjust the desired settings in the camera menu, using function buttons.
• Put on the camera bubble again, matching screws to the corresponding holes located in the base
of the camera and screwing until slight resistance is felt. Please ensure that the mask doesn’t
block camera’s field of view.
INSTALLATION