Novus NVIP-6DN5022H/IRH-1P User manual

U s e r ’s m a n u a l
(sh o r t)
NVIP-6DN5022H/IRH-1P

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
2
IMPORTANT SAFEGUARDS AND WARNINGS
EMC (2004/108/EC) and LVD (2006/95/EC ) Directives
CE Marking
Our products are manufactured to comply with requirements of the following directives and national regulations
implementing the directives:
 Electromagnetic compatibility EMC 2004/108/EC.
 Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical
equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as
75VDC and 1500VDC.
WEEE Directive 2012/19/EU
Information on Disposal for Users of Waste Electrical and Electronic Equipment
This appliance is marked according to the European 1000VAC Directive on Waste Electrical and
Electronic Equipment (2012/19/EU) and further amendments. By ensuring this product is disposed of correctly,
you will help to prevent potential negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product.
The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be
treated as household waste. It shall be handed over to the applicable collection point for used up electrical and
electronic equipment for recycling purpose. For more information about recycling of this product, please contact
your local authorities, your household waste disposal service or the shop where you purchased the product.
RoHS Directive 2011/65/EU
Out of concern for human health protection and friendly environment, we assure that our products
falling under RoHS Directive regulations, regarding the restriction of the use of hazardous
substances in electrical and electronic equipment, have been designed and manufactured in
compliance with the above mentioned regulations. Simultaneously, we claim that our products have
been tested and do not contain hazardous substances whose exceeding limits could have negative
impact on human health or natural environment
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed for self
installation in households by individuals without technical knowledge.
Excluding of responsibility in case of damaging data on a disk or other devices:
The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices
during device operation.
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN
USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES
NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE
CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR
THE RESULTS OF SUCH AN ACTION.

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
3
IMPORTANT SAFEGUARDS AND WARNINGS
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER
DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH
THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER
-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL
MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
1. Prior to undertaking any action please consult the following manual and read all the safety and operating
instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is
necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s
manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer is
forbidden;
7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not
recommended since it may lead to heat build-up and damaging the device itself as a consequence;
8. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly
mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted
by qualified personnel with proper authorization, in accordance with this user’s manual.
9. Device should be supplied only from a power sources whose parameters are in accordance with those
specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera
from a power sources with unknown parameters, unstable or not meeting producer’s requirements;
Due to the product being constantly enhanced and optimized, certain parameters and functions
described in the manual in question may change without further notice.
We strongly suggest visiting the www.novuscctv.com website in order to access the newest full
manual.

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
4
TABLE OF CONTENTS.....................................................................................................4
1. FOREWORD INFORMATION .....................................................................................5
1.1. General Characteristics........................................................................................5
1.2. NVIP-6DN5022H/IRH-1P specification...............................................................6
2. SPECIFICATION ............................................................................................................7
2.1. Camera dimension ..............................................................................................7
2.2. Package contents..................................................................................................8
2.3. Layout of important camera items.......................................................................8
3. INSTALLATION .............................................................................................................9
3.1. Connecting Ethernet cable ..................................................................................9
3.2. Camera installation ............................................................................................10
4. START-UP AND INITIAL CAMERA CONFIGURATION ....................................12
4.1. Starting the IP camera........................................................................................12
4.2. Initial configuration via the Web browser.........................................................13
5. NETWORK CONNECTION UTILIZING WEB BROSWER ................................14
5.1. Recommended PC specification for web browser .............................................14
5.2. Connection with IP camera via the web browser ...............................................14
6. WWW INTERFACE - WORKING WITH IP CAMERA.........................................18
6.1. Displaying live pictures......................................................................................18
7. ELECTRIC CONNECTORS AND ACCESORIES .................................................20
7.1. Connecting power supply to the camera. ..........................................................20
7.2. Connecting alarm inputs/outputs .......................................................................20
7.3. SD card installation ...........................................................................................22
8. RESTORING FACTORY DEFAULTS .....................................................................23
8.1. Restoring software factory defaults....................................................................23
8.2. Restoring hardware factory defaults in IP cameras...........................................23
TABLE OF CONTENTS

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
5
1. FOREWORD INFORMATION
1.1. General Characteristics
 Imager resolution: 6.0 megapixels Mechanical IR cut filter
 Mechanical IR cut filter
 IR operation capability
 Min. Illumination from 0.005 lx/F=1.5
 Digital Slow Shutter (DSS)
 Digital Noise Reduction (DNR)
 Defog Function (F-DNR)
 High Light Compensation (HLC)
 Lens type: varifocal auto iris DC, f=3 ~ 12 mm/F1.5
 Built-in IR illuminator, 17 LEDs
 Privacy zones: 5
 Video compression: H.264, M-JPEG
 Max video processing resolution: 3072 x 2048
 Double streaming: compression, resolution, speed and quality defined individually for each video
stream
 RTSP protocol support for video transmission
 Pre & post-alarm functions
 Video Content Analysis (VCA) functions: tamper detection, abandoned object detection, object
disappearance detection, line cross detection, zone entrance detection, double line cross detection,
loiter detection, multi loiter detection, abnormal speed detection, converse detection, illegal
parking detection
 Hardware motion detection
 Built-in webserver: camera configuration through the website
 SD/SDHC/SDXC/microSD/microSDHC/microSDXC card support
 Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server,
saving file on SD/SDHC/microSD/microSDHCcard, saving file on NAS
 Network protocol support : ONVIF 2.2 (Profile S), HTTP, TCP/IP, IPv4, UDP, HTTPS,
Multicast, DHCP, NTP, RTSP, PPPoE
 Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,
playback and remote IP devices administration
 Built-in heater
 Degree of protection IP66
 Power supply: 12VDC, PoE (Power over Ethernet)
FOREWORD INFORMATION

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
6
1.2. NVIP-6DN5022H/IRH-1P specification
FOREWORD INFORMATION
Image
Image Sensor 6 MPX CMOS sensor 1/1.8” SONY Exmor R STARVIS
Min. Illumination
0.01 lx/F1.5 - color mode,
0.005 lx/F1.5 - color mode (DSS),
0 lx (IR on) - B/W mode
Electronic Shutter auto/manual: 1/5 s ~ 1/20000 s
Digital Slow Shutter (DSS) up to 1/5 s
Wide Dynamic Range (WDR) yes
Digital Noise Reduction (DNR) 2D, 3D
Defog Function (F-DNR) yes
High Light Compensation (HLC) yes
Lens
Lens Type varifocal auto iris DC, f=3 ~ 12 mm/F1.5
Day/Night
Switching Type mechanical IR cut filter
Switching Mode auto, manual, time
Switching Level Adjustment yes
Switching Schedule yes
Visible Light Sensor yes
Network
Stream Resolution 3072 x 2048, 2688 x 1520, 1920 x 1080 (Full HD), 1280 x 720 (HD), 720 x 576 (D1), 320 x 240 (QVGA)
Frame Rate 25 fps for 3072 x 2048 and lower resolutions
Multistreaming Mode 2 streams
Video/Audio Compression H.264, MJPEG/G.711, RAW_PCM
Number of Simultaneous Connections max. 8
Bandwidth 25 Mb/s in total
Network Protocols Support HTTP, TCP/IP, IPv4, UDP, HTTPS, Multicast, DHCP, NTP, RTSP, PPPoE
ONVIF Protocol Support Profile S (ONVIF2.2)
Camera Configuration from Internet Explorer, Firefox, Chrome, Opera browser
languages: Polish, English, Russian, and others
Compatible Software NMS
Other functions
Privacy Zones yes
Motion Detection yes
Video Content Analysis (VCA)
tamper detection, abandoned object detection, object disappearance detection, line cross detection, zone en-
trance detection, double line cross detection, loiter detection, multi loiter detection, abnormal speed detection,
converse detection, illegal parking detection
Image Processing 180˚ image rotation, sharpening, mirror effect
Prealarm/Postalarm up to 5 MB/up to 86400 s
System Reaction to Alarm Events e-mail with attachment, saving file on SD card
IR LED
LED Number 17
Range 40 m
Angle 90°
Interfaces
Video Output BNC, 1.0 Vp-p, 75 Ohm - maintenance only
Audio Input/Output 1 x RCA/1 x RCA
Alarm Input/Output 1 (NO/NC)/1
Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s
Memory Card Slot microSD
Installation parameters
Dimensions (mm) with bracket: 110 (Ф) x 377 (L)
Weight 1.7 kg
Enclosure aluminium, white, fully cable managed wall mount bracket in-set included
Power Supply PoE, 12 VDC
Power Consumption 6 W,
15 W (IR and heater on)
Operating Temperature -30°C ~ 60°C
Degree of Protection IP 66

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
7
SPECIFICATION
2. SPECIFICATION
2.1. Camera dimensions

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
8
1.4. Package contents
After you open the package make sure that the following elements are inside:
 IP camera
 230 VAC / 12 VDC power supply
 Accessories bag
 Short version of user’s manual
 CD containing manual and software
If any of this elements has been damaged during transport, pack all the elements back into the original
box and contact your supplier for further assistance.
CAUTION!
If the device was brought from a location with lower temperature, please wait until it reaches the
temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.
2.2. Package contents
After you open the package make sure that the following elements are inside:
 IP camera,
 Mounting Screw Kit
 Mounting Plate,
 RCA-to-BNC Test Cable,
 Mounting Template,
 Short version of user’s manual,
If any of this elements has been damaged during transport, pack all the elements back into the original
box and contact your supplier for further assistance.
CAUTION!
If the device was brought from a location with lower temperature, please wait until it reaches the
temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
CAUTION! We strongly suggest visiting the www.novuscctv.com website in order to access the
newest full version of the manual.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.
2.3. Layout of important camera items
SPECIFICATION
Focus
adjustment
Zoom
adjustment
Status
LEDs
Reset button
(reverts to factory defaults)
SD card slot
(max. 64GB supported)
RCA service
analog output

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
9
1.4. Package contents
After you open the package make sure that the following elements are inside:
 IP camera
 230 VAC / 12 VDC power supply
 Accessories bag
 Short version of user’s manual
 CD containing manual and software
If any of this elements has been damaged during transport, pack all the elements back into the original
box and contact your supplier for further assistance.
CAUTION!
If the device was brought from a location with lower temperature, please wait until it reaches the
temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.
3. INSTALLATION
3.1 Connecting Ethernet cable
To maintain tightness of Ethernet cable connection, please follow instruction below:
1. Loosen the nut (a) from the main element (b).
2. Run power cable (without RJ-45 connector) though both elements. Then crimp the cable with RJ-45
connector. Install rubber gasket (d) on the connector (c).
3. Connect the cable to the hermetic connector (c), screw main cover (b), then screw the nut (a).
CAUTION! The other camera connectors are not hermetic. User should seal them by himself.
SPECIFICATION
Cable overview with connectors description
1. 100 Mb/s Ethernet port (RJ-45 connector)
2. Power supply 12VDC
CAUTION! Please pay attention to ensure
the correct power supply polarity!
3. Audio Input (RCA)
2. Audio Output (RCA)
5. Alarm input/output connectors
- alarm input (COM0 - orange)
- alarm input (IN0 - yellow)
- alarm output (COM1 - purple)
- alarm output (OUT1 - grey)
a b
a
b
c
d

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
10
3.2 Camera installation
 Put mounting drawing paper to the wall or ceiling and mark drill holes.
 Drill holes using markings.
 Drill additional hole for video and power cables.
 Using mounting screws from the package, attach the mounting plate of camera to the ceiling/
wall. Align the mounting plate with the TOP mark facing you .
 Make sure the hinge screw is attached to the back of the ca m e ra .
 Put video and power cables through a previously drilled hole in the wall/ceiling.
 Align the TOP mark on the camera base with the TOP mark on the mounting plate, rotate the
camera approximately 10° clockwise, and then rotate the c a mer a counterclockwise to slide the
hinge screw into the notch on the mounting plate.
INSTALLATION
TOP
Mounting screw
holes
Mounting
plate
Hinge screw
TOP mark on
camera base
TOP mark on
mounting plate
Mounting plate
notch

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
11
 Attach the camera to the mounting plate using the allen screws.
 (Optional) Unscrew the service compartment screw and open the service compartment. Connect
the RCA service analog output to monitor.
 Make connections of all necessary electrical connectors (description in chapter 7 of this user’s
manual).
 Manually point the camera in a desired direction to obtain a desired scene view.
 Use a Philip’s head screwdriver to adjust the camera zoom and focus as needed. It is
recommended to check focus settings in infrared illumination and make correction in color mode
to have proper focus in both modes.
INSTALLATION
Allows you to rotate
the camera 360°
Allows you to tilt the camera
and camera stand 90°
Allows you to rotate the camera
and camera stand 360°
Focus
adjustment
Zoom
adjustment
Service compartment
screw

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
12
4, START-UP AND INITIAL CAMERA CONFIGURATION
4.1. Starting the IP camera
To run NOVUS IP camera you have to connect Ethernet cable between camera and network switch
with PoE support.
You can also connect it directly via power supply adapter with parameters compatible with camera
power supply specification.
After connecting power supply initialization process is started, which takes about 2 minutes.
The recommended way to start an IP camera and perform its configuration is connect directly to the
network switch which is not connected to other devices. To obtain further information about network
configuration parameters (IP address, gateway, network mask, etc.) please contact your network
administrator.
 Connection utilising network switch with PoE support
 Connection utilising external power supply and network switch
START-UP AND INITIAL CAMERA CONFIGURATION
Power supply and
Computer
IP Camera Network Switch PoE
Network transmission
IP Camera
Network transmission
Network Switch PoE Computer
Network transmission
PSU

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
13
 Connection utilising external power supply directly to the computer
Information:
Power supply adapter is not included. Please use power adapter with parameters specified in user’s
manual.
Caution:
In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge
protectors is advised. Any damages resulting from surges are not eligible for service repairs.
4.2. Initial configuration via the web browser
The default network settings for NVIP-6DN5022H/IRH-1P camera are :
1. IP address= 192.168.1.200
2. Network mask - 255.255.255.0
3. Gateway - 192.168.1.1
4. User name - root
5. Password - pass
Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can
operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from
192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for
camera and PC computer
You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera
yourself or select DHCP mode (DHCP server is required in this method in target network) by using
web browser or by NMS software. When you use DHCP server check IP address lease and its linking
with camera MAC address to avoid changing or losing IP address during device operation or network/
DHCP server breakdown. You have to remember to use a new camera IP address after changing
network parameters.
After network setting configuration has been done, the camera can be connected to a target network.
START-UP AND INITIAL CAMERA CONFIGURATION
IP Camera
Network transmission - cross over cable
Computer
PSU

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
14
5. NETWORK CONNECTION UTILIZING WEB BROSWER
5.1. Recommended PC specification for web browser connections
Requirements below apply to connection with an IP camera, assuming image display in 3072 x 2048
resolution and 25 fps speed.
1. CPU Intel Pentium IV 3 GHz or newer
2. RAM Memory min. 512 MB
3. VGA card (any displaying Direct 3D with min. 128 MB RAM memory)
4. OS Windows XP / Windows Vista / Windows 7 / Windows 8 / Windows 8.1 / Windows 10
5. Direct X version 9.0 or newer
6. Network card 10/100/1000 Mb/s
5.2. Connection with IP camera via the web browser
You have to enter camera IP address in the Internet browser address bar. If IP address is correct user
login window will be displayed:
Default user is root and default password is pass.
In the Language box you can change the display language (English, Polish or Russian). The default
language is English.
For safety reasons, it is recommended to change default user name and password.
It is possible to connect to the camera using Internet Explorer, Mozilla Firefox, Chrome or Opera
browsers. Running the IP camera in this browsers are very similar.
NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
15
If your computer has Flash Player ins t a ll ed, the main screen for the camera web interface opens.
From here you can view and configure the ca m e ra .
If your computer does not have Flash Player ins t a ll ed or its version is version is inappropriate below
window will occur :
To get in the browser image from the camera and be able to configure all functions of the camera,
it is necessary to install Adobe Flash Player.
In order to install latest version od FlashPlayer software Click Please download the latest version of
Flash Player to play live video. Opens a link to download Flash Player from Adobe’s website. After
completing the installation, restart your browser and reconnect to the camera.
Part of the camera features such as: playback of the installed SD card, listening to audio,
bidirectional audio transmission is available only with Internet Explorer browser after installing
the ActiveX plugin. Using ActiveX plugin also allows you to display an image with less delay. In
order to install the ActiveX plug please connect to the camera using a Internet Explorer web
browser (recommended version of the browser is IE11), and proceed as described below:
 Select Download, and then click Run and follow the on-screen instructions to install the
ActiveX plugin. After installation, restart the browser.
NOTE: When working in Windows Vista/ 7/ 8/ 8.1/ 10 the ActiveX applet may be blocked by
Windows Defender or User account control. In such case you should allow to run this applet, or simply
disable these functions.
NETWORK CONNECTION UTILIZING WEB BROWSER
Can not play the video, please download Flash Player and
install it
• Please download the latest version of Flash Player
• Click here to shift playing live video with short delay widget
Please reopen the browser after installing Flash Player

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
16
NETWORK CONNECTION UTILIZING WEB BROWSER
 During connecting with the camera after restarting the web browser please select Allow when
below window will appear.
NOTE: If you are running Windows Vista/7/8/8.1/10 with Internet Explorer 11, the ActiveX applet
can be blocked through browser security settings. In this situation, you should: add the IP address of
the camera to the view of compatibility (Tools -> Compatibility View Settings, click Add).

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
17
NETWORK CONNECTION UTILIZING WEB BROWSER
Then, in the security settings options, add the camera address to trusted sites and lower the secu-
rity level to a minimum.
After making the changes, restart the browser, re-connect to the camera and log on.

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
18
6. WWW INTERFACE - WORKING WITH IP CAMERA
6.1. Displaying live pictures
1. Camera settings
Live Video - Live video preview
Device Info - Device information
Stream Configuration - Video and audio settings for each stream
Device Configuration - Device configuration (e.g. Local Network, Date&Time)
External Device - External device configuration (function unavailable)
Intelligent Analysis - Settings of video analysis
Alarm Configuration - Alarm Configuration (Motion alarm, Alarm I/O)
Local Record - Local Record Configuration
Privacy Masking - Configuration up to 5 privacy masks
Network Service - Network services configuration (e.g. DDNS)
Service Center - Service center configuration (e.g. SMTP)
Privilege Manager - Users and groups management
Protocol - Protocols settings (e.g. ONVIF)
Device Log - Device Log contains: Operation Log, Alarm Log and Collect Log
Maintenance - Device Restart and restoring Default Settings
CAUTION! Compatibility of analysis functions depends on recording device.
WWW INTERFACE - WORKING WITH IP CAMERA
3.
4.
1. 2.
5.

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
19
WWW INTERFACE - WORKING WITH IP CAMERA
2. Video Parameter
Stream - Stream ID (choose one from available streams)
Bite Rate Type - Information about bit rate type
Bit Rate (kbps) - Information about bit rate
I Frame Interval - Information about I frame interval
Quality - Information about quality
3. PTZ configure
Function unavailable.
4. Menu bar
Change Password - Change users password
NOTICE: Default password "pass" can be restored only after restoring default settings of the
camera)
Sign Out - Log out from camera
5. Video Control
Camera - Default number of the camera is 1.
Video - Turn on/off video
Inteligent Analysis - Turn on/off graphic illustration of the analysis.
NOTICE: Inteligent Analysis functions will not be available when using Activex instead of
Flash.
Audio - Turn on/off audio
Interphone - Turn on/off Interphone
NOTICE: Audio and Interphone functions will not be available when using Flash instead of
Activex.
CAUTION! We strongly suggest visiting the www.novuscctv.com website in order to access the
newest full version of the manual.

NVIP-6DN5022H/IRH-1P User’s manual (short form) ver.1.0
All rights reserved © AAT Holding S.A.
20
7. ELECTRIC CONNECTORS AND ACCESORIES
7.1. Connecting power supply to the camera.
The camera can be supplied by using RJ45 network socket. To run NOVUS IP camera you have to
connect Ethernet cable between camera and network switch with PoE support. You can also use a PoE
power injector.
Camera can be also supplied directly via power supply adapter with parameters compatible with
camera power supply specification.
Information:
Power supply adapter is not included. Please use power adapter with parameters specified in user’s
manual.
Caution:
In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge
protectors is advised. Any damages resulting from surges are not eligible for service repairs.
7.2. Connecting alarm inputs/outputs.
Alarm input/output connectors are described in the chapter 2.3 of this user’s manual.
Alarm input
 Alarm input connections
ELECTRIC CONNECTORS AND ACCESORIES
12 VDC +
12 VDC -
12 VDC power supply connection diagram
Alarm input
(-)
(COM0 -
orange)
IP Camera
Alarm input
(+)
(IN0 -
yellow)
Switch/sensor