Novus VAHD-2DN5102MD/IR-1 User manual

NVAHD-2DN5102MD/IR-1
User manual

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
2
IMPORTANT SAFEGUARDS AND WARNINGS
THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed
for self installation in households by individuals without technical knowledge.
Excluding of responsibility in case of damaging data on a disk or other devices:
The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other
devices during device operation.
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN
PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE
PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE
PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING
THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.
DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 26 February 2014 on the harmonisation of the laws of the Member States
relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79–106, with changes)
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE)
(OJ L 197, 24.7.2012, p. 38–71, with changes)
DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances in
electrical and electronic equipment (OJ L 174, 1.7.2011, p. 88–110, with changes)
Pictures in this publication showing camera views can be simulations. Actual camera
images may vary depending on the type, model, settings, observation area, or
environmental conditions.
The manufacturer reserves the right to print errors and change technical parameters
without prior notice.

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
3
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER
DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH
THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER-
SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL
MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.
IMPORTANT SAFEGUARDS AND WARNINGS
1. Prior to undertaking any action please consult the following manual and read all the safety and
operating instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual
is necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the
user’s manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer is
forbidden;
7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)
is not recommended since it may lead to heat build-up and damaging the device itself as a
consequence;
8. Mounting the camera on unstable surface or using not recommended mounts is forbidden.
Improperly mounted camera may cause a fatal accident or may be seriously damaged itself. The
camera must be mounted by qualified personnel with proper authorization, in accordance with this
user’s manual.
9. Device should be supplied only from a power sources whose parameters are in accordance with
those specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply
the camera from a power sources with unknown parameters, unstable or not meeting producer’s
requirements;
10. Signal cables (conducting TV or / and telemetric signal) should be placed in a way excluding the
possibility of damaging them by accident. Special attention must be paid to cables getting from the
camera and connecting the power supply;
11. To avoid equipment damage, whole TV circuit should be equipped with properly made
discharge-, overload- and lightning protection devices. Usage of separating transformers is advised;
IMPORTANT SAFEGUARDS AND WARNINGS

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
4
12. Electric installation supplying the device should be designed to meet the specifications given
by the producer in such a way that overloading is impossible;
13. User cannot repair or upgrade the equipment himself. All maintenance actions and repairs should
be conducted only by qualified service personnel;
14. Unplug the camera from the power source immediately and contact the proper maintenance
department when the following occurs:
• Damages to the power cord or to the plug itself;
• Liquids getting inside the device or exposure to strong mechanical shock;
• Device behaves in a way not described in the manual and all adjustments approved by the
manufacturer and possible to apply by user himself, seem not to have any effect;
• Camera is damaged;
• Atypical behaviour of the camera components may be seen (heard).
15. In necessity of repairs attention to using only original replacement parts (with their parameters
in accordance with those specified by the producer) should be paid. Non-licensed service and
non-genuine replacement parts may cause fire or electrocution;
16. After maintenance activities tests should be run to ensure proper operation of all the functional
components of the device.
Novus AHD cameras are dedicated to work with Novus AHD DVRs. Using only Novus products
guarantees the highest image quality. Connecting Novus AHD cameras to DVRs from other
manufacturers may decrease video quality.
Due to the product being constantly enhanced and optimized, certain parameters and functions
described in the manual in question may change without further notice.
We strongly suggest visiting the www.novuscctv.com/en website in order to access the newest full
manual
IMPORTANT SAFEGUARDS AND WARNINGS

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
5
1. PACKAGE CONTENTS
• NVAHD-2DN5102MD/IR-1 camera
• User’s manual
• A set of screws and dowels
• Mounting template
If any of the listed equipment has been damaged during transport or if the package is incomplete, the
contents of package should be packed back in to the original box. Please contact your local NOVUS
distributor for further assistance.
2. MAIN CHARACTERISTIC
• Mechanical IR cut filter
• IR operation capability
• Horizontal resolution: 1080p
• Min. illumination: from 0.0001 lx/F=1.4 (0lx with IR on)
• Lens type: varifocal, f=2.8 ~ 12mm
• Built-in IR illuminator: 24 high-power LED
• Light sensor
• 2DNR and 3DNR digital noise reduction
• WDR - wide dynamic range
• SENS-UP - digital slow shutter (DSS)
• BLC - back light compensation
• HLC - high light compensation
• DEFOG - improves visibility during fog and rain
• The ability to work in 1080p AHD, CVI,TVI and analog 960H mode
• Stabilization of IR LED current for extending their service life
• Other functions:
–4 motion detection zones,
–4 privacy zones,
–mirror effect, freeze, negative image
–defective pixels correction
–defining the camera name
–adjusting the brightness and sharpness
• Operation in PAL and NTSC systems
• OSD menu
• Power supply: 12VDC
FOREWORD INFORMATION

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
6
3. SPECIFICATION
IMAGE
Image Sensor CMOS sensor 1/2.9” SONY
Operang mode AHD 1080p, TVI 1080p, CVI 1080p, analog 960H
Number of Eecve Pixels 1920 (H) x 1080 (V)
Resoluon 1080p
Min. Illuminaon
0.1 lx/F1.4 - color mode,
0.05 lx/F1.4 - B/W mode,
0.005 lx/F1.4 - color mode (DSS),
0.0001 lx/F1.4 - B/W mode (DSS),
0 lx (IR on) - B/W mode
S/N Rao > 52 dB (AGC o)
Electronic Shuer auto/manual: 1/25 s ~ 1/50000 s (AHD)
Digital Slow Shuer (DSS) up to 30x
High Light Compensaon (HLC) yes
Wide Dynamic Range (WDR) yes
Digital Noise Reducon (DNR) 2D, 3D
Defog Funcon (F-DNR) yes
LENS
Lens Type varifocal, f=2.8 ~ 12 mm/F1.4
DAY/NIGHT
Switching Type mechanical IR cut lter
Switching Mode auto, manual
Switching Level Adjustment yes
Switching Delay 0 ~ 60 s
Visible Light Sensor yes
OTHER FUNCTIONS
OSD languages: Polish, English, Russian, others
Privacy Zones 4
Moon Detecon yes
Image Processing 180˚ image rotaon, sharpening, mirror eect
Remote control yes (COAX protocol)
IR LED
LED Number 24
Range 15 m
Angle 120°
INTERFACES
Video Output BNC, 1.0 Vp-p, 75 Ohm
NSTALLATION PARAMETERS
Dimensions (mm) 112 (Ф) x 87 (H)
Weight 0.17 kg
Enclosure plasc, white
Power Supply 12 VDC
Power Consumpon 1 W , 2.7 W (IR on)
Operang Temperature -30°C ~ 40°C
SPECIFICATION

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
7
3.1. Dimensions:
Dimensions are given in millimeters
3.2. View of the camera, layout of the camera items:
Vercal
adjustment
Zoom adjustment
Horizontal
adjustment
Focus adjustment
Lens
Light Sensor
IR LED’s
Joysck
SPECIFICATION

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
8
4. INSTALLATION
Please familiarize yourself with the device, its parameters and methods of mounting, before mounting.
 Put mounting drawing paper to the wall or ceiling and mark drill holes.
 Drill holes using markings.
 Drill additional hole for video and power cables.
 Please mount the camera using included screws. Please pay special attention to sealing the
mounting holes with an appropriate sealing mass.
 Adjust the position of the camera module.
 Unscrew the blocking screws and adjust focal length and focus.
 If needed, adjust the desired settings in the camera menu, using function buttons.
 Put on the camera bubble again
4.1. Power supply connection
Caution!
Camera should be supplied only from a power sources whose parameters are in accordance with those
specified by producer in the camera’s technical datasheet. Therefore, it is forbidden to supply the
camera from power sources whose parameters are unknown, unstable or not meeting the producer’s
requirements.
4.2 Camera mode settings
Camera got four video modes: TVI, AHD, CVBS and CVI. Depends on used DVR. User need to set
DIP switches according to the picture:
12V DC +/- 10%
wideo
video
ground (GND)
+
- (GND)
INSTALLATION

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
9
5. SETTINGS
The camera has an OSD menu displayed in the foreground of image. During normal operation status
information can be displayed on the image. To navigate menu and make changes please use
joystick located under the camera dome (pointed by arrow):
To enter the menu, press the joystick, which sends ENTER command to the device. To choose
submenu, select the UP, DOWN (U, D) directions. If the sub-menu contains the symbol  that indicates
the opportunity to enter to the settings by pressing the ENTER key. To change the parameters of
selected items, press LEFT, RIGHT buttons. To exit the menu and saves changes, select EXIT and next
select SAVE&END. By selecting RESET you can restore the factory settings, and by selecting NOT SAVE
you can exit the menu without saving changes. To exit the submenu, select RETURN and press ENTER.
Choosing (with left or right button) SAVE&END in the RETURN position saves changes and closes the
menu.
SETTINGS
In case of the image failure after connecting camera, or video loss due to changes in the menu,
it is possible to restore the factory settings. Following procedure is also recommended when
camera menu is not working. To restore factory settings:
1. Turn the power off and on again.
2. If the picture does not appear, perform the following sequence of joystick keys: press
ENTER, UP, RIGHT, press ENTER.
Successful completing these steps restores factory settings (AHD 1080p, PAL).

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
10
5.1. Main menu
Caution: the current menu and options can be different then the one show below if user select other
mode then AHD.
In order to enter the menu press the joystick button (ENTER command). The following menu is
displayed on the screen:
5.1.1 LENS submenu
This submenu allows to set lens parameters:
MANUAL - manual iris lens or fixed iris lens
DC - auto iris mode (DC signal control) - opens another sub-menu.
MODE - selects the operating inside mode (INDOOR) or outside mode (OUTDOOR)
IRIS SPEED - sets the shutter speed (0 to 15).
OUTDOOR mode opens another sub-menu where you can set the minimum and maximum
aperture.
5.1.2 EXPOSURE submenu
This submenu contains exposure and shutter speed settings.
SETTINGS

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
11
SHUTTER - shutter mode control. Allows you to choose the automatic mode (AUTO), the manual
mode with adjustable shutter speed in the range of 1/25 ~ 1/50000s and ability to enable the
DSS function in the range from x2 to x30, and flicker reduction (FLK).
AGC - Sets AGC gain. Higher gain make a scene brighter, but noise increases. It allows to
adjust the gain in the range from 0 to 15.
SENSUP - Digital Slow Shutter function - helps to obtain better, brighter images in low light by
selecting the multiplier of shutter speed in the range from x2 to x30 (opens another sub-menu).
BRIGHTNESS - sets brightness level in the range from 1 to 100.
D-WDR - this function allows to enable/disable wide dynamic range function that enables to
observe the scene with different illumination levels. After selecting this function, there is
a submenu to adjust the level in the range from 0 to 8.
DEFOG - allows you to enable correction functions of image disrupted by the influence of fog,
rain, etc. It opens another sub-menu that allows you to set the zone and the degree of noise
reduction.
5.1.3 BACKLIGHT submenu
These compensation functions allow to enhance visibility of the objects located in the foreground,
surrounded by strongly illuminated background (BLC) or for enhancing visibility of the objects located
near the strong light source (HSBLC).
BLC - function allows to enhance visibility of the objects located in the foreground, surrounded
by strongly illuminated background. Pressing ENTER button in this mode displays the following
menu:
Submenu presented allows to set the size and location of the area where the BLC function is
active, furthermore it allows to set the sensitivity of the function.
HSBLC - high light compensation function. It allows to enhance visibility of the objects located
near the strong, point light source. If a strong, point light source appears on the screen , function
will mask it for effective observation of the scene itself (this function is recommended e.g. to
observe car licence plates). Selecting HSBLC displays following screen:
SETTINGS

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
12
SELECT - allows to select one of the four areas of HSBLC function
DISPLAY - enables or disables previously selected zone.
BLACK MASK - enables or disables masking area
LEVEL - adjusts intensity function between 0-100
MODE - (ALL DAY/NIGHT) determines whether the function is running all the time or only at
night (recommended).
DEFAULT - restores default HSBLC settings.
5.1.4 WHITE BAL submenu
This feature allows to set appropriate color settings using following options:
ATW - auto tracking white balance based on color temperature.
AWC→SET - this mode enables adaptive setting of white balance. In order to obtain the
optimum state under the current illumination, direct the camera at a sheet of white paper and
press ENTER. When lighting parameters change (e.g. light bulbs changed to halogen lamps,
daylight to artificial light etc. ), procedure mentioned above should be repeated;
AWB - auto white balance adjustment.
MANUAL - manual mode settings. In case of inappropriate color settings for ATW, AWC
modes it is possible to set RED and BLUE values manually. Color values range from 0 to 100
and are represented by sliders. Any change in the color components are instantly applied to the
image.
5.1.5 D&N submenu
Allows to adjust day/night settings. Available settings are: AUTO, EXT, COLOR, B/W.
AUTO - camera switches between night (b/w) and day (color) mode automatically, depending on
current illumination conditions. Settings are available at following sub-menu:
D--N (CDS) and N--D (CDS) - sets the illumination threshold that switches the camera from day
to night mode and from night to day mode (respectively 6~255 and 0~249)
D--N (DELAY) and N--D (DELAY) - sets the delay between color and b/w mode switching and
between b/w and color mode (0~60s)
SETTINGS

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
13
B/W - forces continuous black & white mode. Selecting displays following submenu for
adjusting additional values:
BURST - enables/disable chrominance signal synchronization.
IR SMART - function ensuring balanced brightness level of the picture during operation with an
IR illuminator (which prevents overexposure of the objects located close to the camera and its
illuminator). Entering the function allows to set function area and sensitivity, in the same
manner as in motion detection menu.
IR PWM - unavailable
5.1.6 NR submenu
Allows to make settings for digital noise reduction function. Pressing ENTER button in this mode
displays the following menu:
2DNR - allows to set the level of noise reduction for static parts of the image (available settings:
OFF, LOW, MIDDLE, HIGH)
3DNR - allows to set the level of noise reduction variables (dynamic) parts of the image
(available settings: OFF, LOW, MIDDLE, HIGH)
Caution:
In the 960H analog mode only 2DNR noise reduction is available.
5.1.7 SPECIAL submenu
Allows to set additional camera features. Pressing ENTER button in this mode displays the following
menu:
SETTINGS

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
14
CAM TITLE - allows to enter a string of characters that will be displayed on the screen, e.g. as camera
title. Screen contains mainly alphanumerical characters, which may be used in camera’s title.
Select desired character and press ENTER key. Currently edited title is visible at the bottom of
the screen. Line above it contains buttons for editing the title. To enable particular functions,
please highlight them as normal characters and confirm by pressing ENTER. Button functions
are described below:
 - moves character highlight cursor left.
 - moves character highlight cursor right.
POS - adjusts the position of entered characters.
CLR - erases the whole title.
END - exits title editing menu.
D-EFFECT - submenu allows to set additional digital functions:
FREEZE - holds the picture currently displayed.
MIRROR - allows to change viewpoint as MIRROR, ROTATE, V-FLIP.
NEG. IMAGE - enables/disables displaying negative video image.
MOTION - allows (provided that ON option is selected) to turn a built-in motion detection feature on
or off. Motion detection may simultaneously be conducted in four independent zones (with their size
and location selectable by user). Detection of motion displays an „MOTION DETECTED” information
superimposed on the screen.
After selecting ON and pressing ENTER adjust motion detection settings is displayed, as depicted
below:
SELECT - selects the number of the area for further settings.
DISPLAY - turns on/off particular area. Also allows to set the position and size of the area.
SENSITIVITY - refers to sensitivity
COLOR - sets the color visualization of motion in a particular area
TRANS - allows to set the transparency level of visualization
ALARM - displays submenu where user can set motion visualization mode (OFF, BLOCK,
OUTLINE, ALL), enable or disable displaying „MOTION DETECTED” information and set its
display time (1 ~ 15 s). Options ALARM OUT and ALARM SIG are inactive.
DEFAULT - restores default settings.
SETTINGS

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
15
PRIVACY - allows to enable (by selecting ON) privacy zones. Part of the screen may be masked using
four rectangular zones. Selecting ON and pressing ENTER displays a sub-menu, containing four masks
positions.
SELECT - selects the number of the area for further settings.
DISPLAY - turns on/off particular area. Available masking methods: with overlaid color, color
reversal or tessellation (COLOR, INV, MOSAIC). Pressing ENTER after selecting COLOR, INV or
MOSAIC option will open a new submenu which allows to set the position and size of the zone.
COLOR - sets the color masking (available only if COLOR option was chosen).
TRANS - allows you to set the degree of transparency mask (available only if COLOR option was
chosen).
DEFAULT - restores default settings.
LANGUAGE - switches between OSD languages: Polish, English, Russian and others.
DEFECT - allows to adjust parameters used in Dead Pixel Correction function:
LIVE DPC - sets parameters of the defective pixel correction function in real time. Selecting ON
and pressing ENTER button opens a submenu for setting the gain level and the level of
correction.
WHITE DPC - allows to a correct "hot pixels". Selecting ON and pressing ENTER button opens
a submenu where you can specify the size and location of the zone in which the correction will
be made (position POS/SIZE), then define the level of correction and amplification (LEVEL and
AGC positions) and set SENS-UP option (if camera uses SENS-UP position). Then select START
position and press ENTER, cover the lens tightly and press ENTER again. After correcting process
the camera returns to the DPC WHITE menu. In the DPC VIEW you can check the correction effect
and, if needed repeat the operation with different settings.
SETTINGS

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
16
BLACK DPC - allows to correct (mask) dead pixels. Selecting ON and pressing ENTER button
opens a submenu which define the size and location of the zone in which the correction is made
(position POS/SIZE), then define the compensation level (position LEVEL). Then select START
position and press ENTER button and wait for the end of the operation. In the DPC VIEW check
the correction effect and, if needed repeat the operation with different settings.
RS485 - option disabled
5.1.8 ADJUST submenu
It allows to perform additional image adjustment. After pressing ENTER, the following submenu is
displayed:
SHARPNESS - allows to disable (OFF) and enable (AUTO) sharpness correction function. After
selecting AUTO and pressing ENTER, next submenu is displayed, where it is possible to set the
degree of correction and gain ranges for compensation
MONITOR - corrects the image parameters depending on chosen monitor (LCD monitor or CRT
monitor). After pressing ENTER, the submenu is displayed where fine adjustments can be made.
LSC - enables and disables the function of increasing the brightness of the image edge
VIDEO OUT - chooses a system in which the camera works (PAL or NTSC)
INFORMATION:
For camera mode analog 960H in the ADJUST menu there are two additional items:
MONITOR OUT - switches the aspect ratio between 4:3 and 16:9
COMET - option disabled
SETTINGS

NVAHD-2DN5102MD/IR-1 User manual version 1.3
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
17
5.1.9 Camera Setup Menu HIDDEN
Camera has another hidden menu to which you enter by hovering over the EXPOSURE menu three
times clicking RIGHT, and then clicking ENTER.
MONITOR OUT - selecting modes of camera - function not supported
ADC TEST - option that displays data from ADC converter for testing purposes.
FIRMWARE - the current version of the camera firmware.
RETURN - return to the previous menu.
SETTINGS

31.12.2020 MF TF (JZ) (TF) v1.3
AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
431 Pulawska St., 02-801 Warsaw, Poland
tel.: [phone], [email protected]
www.novuscctv.com

NVAHD-2DN5102MD/IR-1
Instrukcja obs ł u g i

NVAHD-2DN5102MD/IR-1 Instrukcja obsługi wersja 1.3
Wszelkie prawa zastrzeżone © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
2
PRODUKT SPEŁNIA WYMAGANIA ZAWARTE W DYREKTYWACH:
Informacja
Urządzenie, jako element profesjonalnego systemu telewizji dozorowej służącego do nadzoru
ikontroli, nie jest przeznaczone do samodzielnego montażu w gospodarstwach domowych przez osoby
nie posiadające specjalistycznej wiedzy.
Wyłączenie odpowiedzialności w przypadku uszkodzenia danych zawartych na dysku lub innych
urządzeniach:
Producent nie ponosi odpowiedzialności w razie uszkodzenia lub utraty w trakcie eksploatacji Produktu
danych zawartych na dyskach lub innych urządzeniach.
Obowiązek konsultowania się z Producentem przed wykonaniem czynności nieprzewidzianej
instrukcją obsługi albo innymi dokumentami:
Przed wykonaniem czynności, która nie jest przewidziana dla danego Produktu w instrukcji obsługi,
innych dokumentach dołączonych do Produktu lub nie wynika ze zwykłego przeznaczenia Produktu,
należy, pod rygorem wyłączenia odpowiedzialności Producenta za następstwa takiej czynności,
skontaktować się z Producentem.
Zamieszczone w niniejszej publikacji zdjęcia przedstawiające obrazy z kamer mogą być
symulacjami. Rzeczywiste obrazy z kamer mogą się różnić, w zależności od typu, modelu,
ustawień, obszaru obserwacji lub warunków zewnętrznych.
DYREKTYWA PARLAMENTU EUROPEJSKIEGO I RADY 2012/19/UE z dnia 4
lipca 2012 r. w sprawie zużytego sprzętu elektrycznego i elektronicznego (WEEE) Dz.U. L
96 z 29.3.2014, str. 79—106, z późniejszymi zmianami) – zwana Dyrektywa WEEE
DYREKTYWA PARLAMENTU EUROPEJSKIEGO I RADY 2014/30/UE z dnia 26
lutego 2014 r. w sprawie harmonizacji ustawodawstw państw członkowskich odnoszących
się do kompatybilności elektromagnetycznej (Dz.U. L 096 z 29.3.2014, s. 79—106, z
późniejszymi zmianami) – zwana Dyrektywa EMC
DYREKTYWA PARLAMENTU EUROPEJSKIEGO I RADY 2011/65/UE
z dnia 8 czerwca 2011 r. w sprawie ograniczenia stosowania niektórych niebezpiecznych
substancji w sprzęcie elektrycznym i elektronicznym (Dz.U. L 174 z 1.7.2011, str. 88—110,
z późniejszymi zmianami) - zwana Dyrektywa RoHS
INFORMACJE
Producent zastrzega sobie możliwość wystąpienia błędów w druku oraz zmian parametrów
technicznych bez uprzedniego powiadomienia.