Ntron ESERV-1xT User manual

ESERV-1xT-1210 R2
820 S. University Blvd., Suite 4 E, Mobile, AL 36609 USA
251.342.2164
www.n-tron.com
Copyright, © N-Tron Corp., 2010
C
Ch he ec ck k f fo or r A Al ll l R Re eq qu ui ir re ed d H Ha ar rd dw wa ar re e
ESERV-1xT module
This Quick Start Guide
CD with Software Manager and manuals
Network cable (not included)
Serial cable(s) (not included)
10 to 58V DC (4W) Power Supply (not
included)
Quick Start Guide
ESERV-1xT Serial Servers
1
I
In ns st ta al ll l t th he e H Ha ar rd dw wa ar re e
2
Connect a 10 to 58 VDC power supply
Connect the network cable from the serial server to a
network drop using a standard network cable. Use a
straight-through Ethernet Cable on copper ports.
Connect the serial device(s):
oRS-232 with DB9: straight-through for DCE
device, null modem for DTE device
oRS-232/422/485 with terminal blocks: see
Appendix D for pinouts
L
LE ED D S St ta at tu us s
LED
STATUS
Ready
Blinks if system is operating correctly
Port 1
On indicates serial port open, blinks when data present on
serial port
Port 2
Same as Port 1
(Present on 2 port units only)
Link
On indicates Ethernet operating in 100BaseTX, blinks
when data present on Ethernet link
3
M
Mo od de e S Sw wi it tc ch h
Hold in Mode switch for…
Result
0 to 2 seconds
Initiates a Hardware Reset
2 to 10 seconds
Enters Console Mode
More than 10 seconds
Resets to Factory Defaults
4
I In ns st ta al ll l M Ma an na ag ge em me en nt t S So of ft tw wa ar re e
Insert the included CD and it should autostart
Follow the prompts to install the Ethernet Serial
Server Manager software.
Note: Be sure you have administrative rights & disable firewalls
in Windows XP and Vista.
5
S
Se et tu up p M Ma an na ag ge em me en nt t S So of ft tw wa ar re e
Open Ethernet Serial Server Manager: click
StartProgramsN-TRONEthernet Serial
Server Manager
The Discovery page opens
To configure via the network, select Network.
If you know the IP address, select The device is
at this address, and type in the address. If not,
select I don’t know the IP address of the device.
Click Connect.
O
OR R… …S Se et tu up p t th he e W We eb b I In nt te er rf fa ac ce e
Open a browser and type the IP address of the
serial server in the Address Bar.
When the serial server is found, the
Configuration window appears.
6
oOne Conductor Per Terminal
oUse Copper Wire Only
oWire Size: 28 to 16 AWG
oTightening Torque: 5 KG -CM
oWire Temperature Rating: 105°C Minimum
(Sized for 60°C ampacity)
o80°C Maximum Surrounding Air Ambient

ESERV-1xT-1210 R2
820 S. University Blvd., Suite 4 E, Mobile, AL 36609 USA
251.342.2164
www.n-tron.com
Copyright, © N-Tron Corp., 2010
L
Lo og gi in n
Click Login. (Password is blank from factory)
The General page appears.
S Se et tu up p t th he e N Ne et tw wo or rk k
The serial server is set at the factory to receive
an IP assignment from a DHCP Server. If a
DHCP server is not available on your network, it
will default to 169.254.102.39.
If this address does not work with your PC,
change your network settings to:
oIP Address = 169.254.102.1
oSubnet Mask = 255.255.255.0
oDefault Gateway = 169.254.102.100
If you need to use different settings, refer to the
Users Manual for instructions.
S
Se et tu up p t th he e S Se er ri ia al l P Po or rt t P Pa ar ra am me et te er rs s
Click Port 1 Serial to open the Serial Port
Parameters page. Select the type of serial
connection between the serial server and the
serial device. (RS-232, RS-422, RS-485 2-wire,
or RS-485 4-wire)
Select the Baud Rate, Data Bits, Stop Bits,
Parity and Flow Control needed to communicate
with the serial device.
If your serial server is 2 port, select the next port
in the Description box, then repeat the previous
steps.
Click Next.
S
Se et tu up p t th he e P Po or rt t N Ne et tw wo or rk k P Pa ar ra am me et te er rs s
Click Port 1 Network to open the Port Network
Parameters page.
Select the type of network protocol you want to
use: TCP, UDP, VCOM or Paired Mode.
If you select TCP, select whether the serial server
will operate as a Client or Server, then configure
the required IP address, port numbers and other
related parameters.
If you select UDP, configure the IP addresses,
ports and other related parameters for the devices
you want to receive from and send to.
If you want the serial server to act as a virtual
communications port for a computer, select
VCOM. This allows your computer to connect to a
serial device on the network as if it were
connected to a physical COM port.
If you want the serial server to operate in Paired
mode with another serial server, select Paired,
then configure it as a client or server and set up
the IP address, port numbers and other related
parameters (similar to setting up TCP).
S Se et tu up p A Ad dv va an nc ce ed d P Pa ar ra am me et te er rs s
If you want to set up Advanced parameters, click
Advanced on the Port Network Parameters
page.
If necessary for your application, select I want to
control when connections are forced closed,
then set up the Network Watchdog and Serial
Watchdog as required.
If necessary for your application, select I want to
control data packets are sent over the network,
then set up the Character Count, Forced
Transmit, Intercharacter Timeout, Delimiters and
Delimiter Removal as required.
Click Next.
S Sa av ve e a an nd d L Lo og go ou ut t
If you have completed the configuration, click
Save to save the configuration to the serial
server.
To Logout, click the Logout button.
T To o T Te es st t a an nd d V Ve er ri if fy y O Op pe er ra at ti io on n
Set up serial server as a TCP Server on serial
port 1.
Set serial port to RS-232 on serial port 1.
Set to 9600 8-N-1 on serial port 1.
Loopback serial port 1 by connecting TD to RD.
Open a DOS window and type “telnet x.x.x.x
yyyy” where x.x.x.x is the IP address of the
serial server and yyyy is the port number of the
serial port.
Type characters on the keyboard. The
characters should appear in the window. If not,
double check your settings.
7
8