Cisco C880 M5 User manual

1
Cisco C880 M5 Server Service Guide
November 2017
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706 USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

2
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT
NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT
ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR
THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE
INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU
ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A
COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as
part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE
PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT OR ARISING FROM ACOURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL
DAMAGES, INCLUDING,WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR
INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of
Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners.
The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and
figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and
coincidental.
© 2017 Cisco Systems, Inc. All rights reserved.

3
Contents
1 Preparations..................................................................................................................... 12
1.1 Outline ....................................................................................................................... 12
1.1.1 Scope.................................................................................................................... 12
1.1.2 Typical time required for assembling options .................................................. 12
1.1.3 Work assignment ................................................................................................ 13
1.1.4 Notes.................................................................................................................... 13
1.2 Preparing Tools for Installation ............................................................................... 14
1.2.1 Tools and measuring instruments..................................................................... 14
1.2.2 Configuration and setting information ............................................................. 15
1.3 Checking Installation Requirements....................................................................... 15
1.3.1 Environmental requirements ............................................................................ 15
1.3.2 Input power......................................................................................................... 16
1.3.3 Input power system ............................................................................................ 17
1.3.4 Installation area ................................................................................................. 18
1.4 Setting the FST ......................................................................................................... 19
1.5 Request to system administrator............................................................................. 20
2 Installing System Board.................................................................................................. 21
2.1 Conditions for installing components ...................................................................... 21
2.1.1 Firmware version................................................................................................ 21
2.1.2 Maximum installation amount.......................................................................... 21
2.1.3 Conditions concerning combined use of System Board.................................... 21
2.1.4 Base Unit state ................................................................................................... 21
2.2 Work Items, Work Assignment, and Work Time..................................................... 22
2.3 Procedure for installing a system board.................................................................. 22
2.3.1 Checking the delivered items ............................................................................ 22
2.3.2 Installing option.................................................................................................. 22
2.4 Verifying operation.................................................................................................... 23
2.5 Preparation of handing over to the system administrator..................................... 26
2.6 Handover to the system administrator.................................................................... 26
3 Installing CPUs................................................................................................................ 27
3.1 Conditions for installing components ...................................................................... 27
3.1.1 Firmware version................................................................................................ 27

4
3.1.2 Maximum installation amount.......................................................................... 27
3.1.3 Conditions concerning mixing different types of CPU..................................... 27
3.1.4 Base Unit state ................................................................................................... 27
3.2 Work Items, Work Assignment, and Work Time..................................................... 28
3.3 Procedure for installing CPUs.................................................................................. 28
3.3.1 Checking the delivered items ............................................................................ 28
3.3.2 Installing option.................................................................................................. 28
4 Installing Memory............................................................................................................ 29
4.1 Conditions for installing components ...................................................................... 29
4.1.1 Firmware version................................................................................................ 29
4.1.2 Number of mounted DIMMs.............................................................................. 29
4.1.3 Conditions on mixing different types of DIMM................................................ 29
4.1.4 Memory installing order..................................................................................... 30
4.1.5 Base Unit state ................................................................................................... 31
4.2 Work Items, Work Assignment, and Work Time..................................................... 32
4.3 Procedure for installing Memory ............................................................................. 32
4.3.1 Checking the delivered items ............................................................................ 32
4.3.2 Installing option (Existing SB).......................................................................... 32
4.3.3 Installing option (New SB)................................................................................. 34
4.4 Verifying operation.................................................................................................... 34
4.5 Preparation of handing over to the system administrator..................................... 37
4.6 Handover to the system administrator.................................................................... 38
5 Installing PCI Card.......................................................................................................... 39
5.1 Conditions for installing components ...................................................................... 39
5.1.1 Firmware version................................................................................................ 39
5.1.2 Maximum installation amount.......................................................................... 39
5.1.3 Conditions concerning combined use of PCI card ............................................ 39
5.1.4 Base Unit state ................................................................................................... 40
5.2 Work Items, Work Assignment, and Work Time..................................................... 40
5.3 Procedure for installing a PCI card ......................................................................... 40
5.3.1 Checking the delivered items ............................................................................ 40
5.3.2 Installing option (Slot#2 or Slot#3) ................................................................... 41
5.3.3 Installing PCI card (Other than slot#2 and slot#3) ......................................... 42
5.4 Verifying operation.................................................................................................... 43
5.5 Preparation of handing over to the system administrator..................................... 45

5
5.6 Handover to the system administrator.................................................................... 45
6 Installing Disk Unit for SAS (DU_SAS)......................................................................... 46
6.1 Conditions for installing components ...................................................................... 46
6.1.1 Firmware version................................................................................................ 46
6.1.2 Maximum installation amount.......................................................................... 46
6.1.3 Conditions concerning combined use of DU_SAS ............................................ 46
6.1.4 Base Unit state ................................................................................................... 46
6.2 Work Items, Work Assignment, and Work Time..................................................... 47
6.3 Procedure for installing a DU_SAS ......................................................................... 47
6.3.1 Checking the delivered items ............................................................................ 47
6.3.2 Installing option.................................................................................................. 47
6.4 Verifying operation.................................................................................................... 48
6.5 Preparation of handing over to the system administrator..................................... 50
6.6 Handover to the system administrator.................................................................... 50
7 Installing Internal Hard Disk Drive (HDD) / Internal Solid State Drive (SSD) ........ 51
7.1 Conditions for installing components ...................................................................... 51
7.1.1 Firmware version................................................................................................ 51
7.1.2 Maximum installation amount.......................................................................... 51
7.1.3 Conditions concerning combined use of HDD / SSD ........................................ 51
7.1.4 Base Unit state ................................................................................................... 51
7.2 Work Items, Work Assignment, and Work Time..................................................... 52
7.3 Procedure for Installing HDD / SSD........................................................................ 52
7.3.1 Checking the delivered items ............................................................................ 52
7.3.2 Installing option (System Power On) ................................................................ 52
7.3.3 Installing option (System Power Off)................................................................ 53
7.4 Verifying operation.................................................................................................... 53
7.5 Preparation of handing over to the system administrator..................................... 55
7.6 Handover to the system administrator.................................................................... 55
8 Installing Disk Unit for PCIe SFF (DU_PCIE) ............................................................. 56
8.1 Conditions for installing components ...................................................................... 56
8.1.1 Firmware version................................................................................................ 56
8.1.2 Maximum installation amount.......................................................................... 56
8.1.3 Conditions concerning combined use of DU_PCIE .......................................... 56
8.1.4 Base Unit state ................................................................................................... 56
8.2 Work Items, Work Assignment, and Work Time..................................................... 57

6
8.3 Procedure for installing DU_PCIE........................................................................... 57
8.3.1 Checking the delivered items ............................................................................ 57
8.3.2 Installing option.................................................................................................. 57
8.4 Verifying operation.................................................................................................... 58
8.5 Preparation of handing over to the system administrator..................................... 60
8.6 Handover to the system administrator.................................................................... 60
9 Installing PCIe SSD SFF (SSD SFF) ............................................................................. 61
9.1 Conditions for installing components ...................................................................... 61
9.1.1 Firmware version................................................................................................ 61
9.1.2 Maximum installation amount.......................................................................... 61
9.1.3 Conditions concerning combined use of SSD SFF............................................ 61
9.1.4 Base Unit state ................................................................................................... 61
9.2 Work Items, Work Assignment, and Work Time..................................................... 62
9.3 Procedure for Installing SSD SFF ........................................................................... 62
9.3.1 Checking the delivered items ............................................................................ 62
9.3.2 Installing option.................................................................................................. 62
9.4 Verifying operation.................................................................................................... 63
9.5 Preparation of handing over to the system administrator..................................... 65
9.6 Handover to the system administrator.................................................................... 65
10 Installing I/O Unit B (IOUB) ........................................................................................ 66
10.1 Conditions for installing components .................................................................... 66
10.1.1 Firmware version ............................................................................................. 66
10.1.2 Maximum installation amount........................................................................ 66
10.1.3 Conditions concerning combined use of IOUB ............................................... 66
10.1.4 Base Unit state ................................................................................................. 66
10.2 Work Items, Work Assignment, and Work Time................................................... 67
10.3 Procedure for installing IOUB ............................................................................... 67
10.3.1 Checking the delivered items .......................................................................... 67
10.3.2 Installing option................................................................................................ 67
10.4 Verifying operation.................................................................................................. 68
10.5 Preparation of handing over to the system administrator................................... 71
10.6 Handover to the system administrator.................................................................. 71
11 Installing Power Supply Unit (PSU) ............................................................................ 72
11.1 Conditions for installing components .................................................................... 72
11.1.1 Firmware version.............................................................................................. 72

7
11.1.2 Maximum installation amount........................................................................ 72
11.1.3 Conditions concerning mixing different types of PSU ................................... 72
11.1.4 Base Unit state ................................................................................................. 72
11.2 Work Items, Work Assignment, and Work Time................................................... 73
11.3 Procedure for installing PSU.................................................................................. 73
11.3.1 Checking the delivered items........................................................................... 73
11.3.2 Installing PSU................................................................................................... 73
11.4 Setup......................................................................................................................... 74
11.5 Verifying operation.................................................................................................. 75
11.5.1 Verifying operation (System Power On).......................................................... 75
11.5.2 Verifying operation (System Power Off).......................................................... 76
11.6 Preparation of handing over to the system administrator................................... 78
11.7 Handover to the system administrator.................................................................. 78
12 Installing M.2 Flash Device .......................................................................................... 79
12.1 Conditions for installing components .................................................................... 79
12.1.1 Firmware version ............................................................................................. 79
12.1.2 Maximum installation amount........................................................................ 79
12.1.3 Conditions concerning combined use of M2.Flash Device............................. 79
12.1.4 Base Unit state ................................................................................................. 79
12.2 Work Items, Work Assignment, and Work Time................................................... 80
12.3 Procedure for Installing M.2 Flash Device............................................................ 80
12.3.1 Checking the delivered items .......................................................................... 80
12.3.2 Installing option................................................................................................ 80
12.4 Verifying operation.................................................................................................. 81
12.5 Preparation of handing over to the system administrator................................... 83
12.6 Handover to the system administrator.................................................................. 83
13 Installing eLCM Activation License ............................................................................. 84
13.1 Conditions for installing components .................................................................... 84
13.1.1 Firmware version ............................................................................................. 84
13.1.2 Maximum installation amount........................................................................ 84
13.1.3 Conditions concerning combined use of Micro SD ......................................... 84
13.1.4 Base Unit state ................................................................................................. 84
13.2 Work Items, Work Assignment, and Work Time................................................... 85
13.3 Procedure for Installing a Micro SD ...................................................................... 85
13.3.1 Checking the delivered items .......................................................................... 85

8
13.3.2 Installing option................................................................................................ 85
13.4 Verifying operation.................................................................................................. 86
13.5 Preparation of handing over to the system administrator................................... 88
13.6 Handover to the system administrator.................................................................. 88
14 Installing TPM ............................................................................................................... 89
14.1 Conditions for installing components .................................................................... 89
14.1.1 Firmware version ............................................................................................. 89
14.1.2 Maximum installation amount........................................................................ 89
14.1.3 Conditions concerning combined use of TPM................................................. 89
14.1.4 Base Unit state ................................................................................................. 89
14.2 Work Items, Work Assignment, and Work Time................................................... 90
14.3 Procedure for Installing TPM................................................................................. 90
14.3.1 Checking the delivered items .......................................................................... 90
14.3.2 Installing option................................................................................................ 90
14.4 Verifying operation.................................................................................................. 91
14.5 Preparation of handing over to the system administrator................................... 93
14.6 Handover to the system administrator.................................................................. 93
Appendix A Installation Instructions Sheet...................................................................... 95
Appendix B Customer's Distribution Panel Breaker Requirements .............................. 96
Appendix C Plug Types....................................................................................................... 98
C.1 Base Unit Plug Types (Global standard) ................................................................ 98
C.2 Power Distribution Box Plug Types........................................................................ 98
Appendix D Input Power Systems..................................................................................... 99
D.1 2 PSUs ....................................................................................................................... 99
D.2 3 PSUs ..................................................................................................................... 100
D.3 4 PSUs ..................................................................................................................... 101
Appendix E Various Operations....................................................................................... 103
E.1 Operation terminal connection.............................................................................. 103
E.1.1 When connect the FST directly to the Base Unit by LAN cable .................. 103
E.1.2 When connect the FST to network switch by LAN cable (DHCP disabled) 103
E.1.3 When connect the FST to network switch by LAN cable (DHCP enabled) . 103
E.1.4 When use the operation terminal of customer equipment connected to the
network....................................................................................................................... 104
E.2 iRMC Web................................................................................................................ 104
E.2.1 Login ................................................................................................................. 104

9
E.2.2 Logout ............................................................................................................... 106
E.3 Video Redirection.................................................................................................... 107
E.3.1 Video Redirection start .................................................................................... 107
E.3.2 Video Redirection end ...................................................................................... 109
E.4 Boot Device Selector setting ...................................................................................110
E.5 Power On/Off............................................................................................................111
E.5.1 Power On ...........................................................................................................111
E.5.2 Power Off ...........................................................................................................113
E.6 Memory Operation Mode setting............................................................................114
E.7 Checking memory type............................................................................................115
E.8 SEL downloading.....................................................................................................116
E.9 Power Restore Policy setting ..................................................................................117
E.10 FBU (BBU) status confirming ..............................................................................118
Appendix F Handling the Units....................................................................................... 120
F.1 Unit location ............................................................................................................ 120
F.2 SB ............................................................................................................................. 121
F.2.1 Installing SB ..................................................................................................... 121
F.2.2 Removing SB..................................................................................................... 122
F.2.3 Installing a cover of SB .................................................................................... 122
F.2.4 Removing a cover of SB.................................................................................... 123
F.3 IOUB ........................................................................................................................ 124
F.3.1 Installing IOUB ................................................................................................ 124
F.3.2 Removing IOUB................................................................................................ 125
F.3.3 Installing IOUB cover ...................................................................................... 125
F.3.4 Removing IOUB cover...................................................................................... 126
F.4 DU_SAS ................................................................................................................... 127
F.4.1 Installing DU_SAS ........................................................................................... 127
F.4.2 Removing DU_SAS........................................................................................... 127
F.5 DU_PCIE ................................................................................................................. 128
F.5.1 Installing DU_PCIE ......................................................................................... 128
F.5.2 Removing DU_PCIE......................................................................................... 128
F.6 PSU........................................................................................................................... 129
F.6.1 Installing PSU .................................................................................................. 129
F.6.2 Removing PSU .................................................................................................. 129
F.7 CPU .......................................................................................................................... 130

10
F.7.1 Installing CPU.................................................................................................. 130
F.8 Memory .................................................................................................................... 136
F.8.1 Installing Memory ............................................................................................ 136
F.8.2 Removing Memory............................................................................................ 138
F.9 PCI card ................................................................................................................... 139
F.9.1 Installing PCI card (Other than slot#2 and slot#3) ....................................... 139
F.9.2 Removing PCI card (Other than slot#2 and slot #3)...................................... 140
F.9.3 Installing PCI card (slot#2 and slot#3)........................................................... 141
F.9.4 Removing PCI card (slot#2 and slot#3)........................................................... 143
F.10 FBU for DU_SAS................................................................................................... 143
F.10.1 Installing a FBU............................................................................................. 143
F.10.2 Installing a TFM module ............................................................................... 145
F.10.3 Connecting FBU cable.................................................................................... 146
F.11 HDD/SSD ............................................................................................................... 147
F.11.1 Installing HDD/SSD ....................................................................................... 147
F.11.2 Removing HDD/SSD....................................................................................... 148
F.12 PCIe SSD SFF ....................................................................................................... 149
F.12.1 Installing PCIe SSD SFF ............................................................................... 149
F.12.2 Removing PCIe SSD SFF............................................................................... 150
F.13 Installing LAN card module................................................................................. 151
F.13.1 10G BASE LAN Card..................................................................................... 151
F.13.2 CAN (FCoE) card (10Gbps)............................................................................ 153
F.13.3 25G BASE LAN card...................................................................................... 154
F.13.4 40G BASE LAN card...................................................................................... 155
F.14 Installing M.2 Flash Device ................................................................................. 156
F.15 Installing eLCM Activation License .................................................................... 157
F.16 FBU for Ext. SAS RAID Card .............................................................................. 158
F.16.1 Installing a TFM module ............................................................................... 158
F.16.2 Connecting the FBU cable to RAID Card..................................................... 159
F.16.3 Connecting FBU cable to connector on IOUB .............................................. 160
F.16.4 Mounting FBU to OPUB................................................................................ 161
F.17 Installing TPM ...................................................................................................... 163
Appendix G Cable Connection Diagram.......................................................................... 164
G.1 Cable Connection Diagram.................................................................................... 164
G.2 Cable Routing ......................................................................................................... 166

11
Appendix H Prevention of Improper Cable Connections ............................................... 167
Appendix I Port number of PCI card............................................................................... 170
I.1 LAN card .................................................................................................................. 170
I.2 Fibre Channel card.................................................................................................. 171
I.3 SAS card / SAS RAID controller card..................................................................... 172
I.4 CNA card .................................................................................................................. 173
I.5 Infiniband HCA card ............................................................................................... 174

12
SET0100000
1 Preparations
This chapter provides an overview, including the addition procedure and addition preparations.
ANNT)
If the work procedure for upgrading starts with AC power off status, set power restoration policy
setting "Restore to powered state prior to power loss" or "Always off" before AC power off.
Make sure the setting with the system administrator and modify it if necessary.
Set the default setting after completing the work procedure for upgrading.
See Appendix E.9 “Power Restore Policy setting” for more information.
SET0101000
1.1 Outline
This chapter provides an overview, including the installation procedure and installation preparations.
SET0101010
1.1.1 Scope
This section describes the scope of the addition instructions, typical time required for assembling
options, work assignment, and notes.
SET0101020
1.1.2 Typical time required for assembling options
The following table lists the typical time required for assembling options.
Table 1.1.2 Typical time required for assembling options
Option
Option work time (minute)
System board
46 / unit
CPU
20 / set
Memory
31 / set
PCI card
36 / card
I/O unit B (IOUB)
36 / unit
Disk unit for SAS (DU_SAS)
46 / unit
Disk unit for PCIe SFF (DU_PCIE)
46 / unit
Internal hard disk drive (HDD)
Internal solid state drive (SSD)
31 / drive
Internal PCIe SSD SFF
31 / drive
Power Supply Unit (PSU)
27 / unit
M.2 Flash Device
36 / unit
eLCM Activation License
36 / unit
TPM
36 / unit

13
SET0101030
1.1.3 Work assignment
“Table 1.1.3-1” lists the relevant addition work items and how they are to be assigned.
Table 1.1.3-1 Assignment of addition work
Work item
Person or department in charge
Preparing for addition work
Service Engineer
Checking the delivered items
Service Engineer
Installing options
Service Engineer
Setup
Service Engineer
Verifying operation
Service Engineer
Preparation of handing over to the System
Administrator
Service Engineer
Handover to system administrator
System Administrator and Service Engineer
SET0101040
1.1.4 Notes
ANNT) Notes on unit delivery
If, after bringing the unit to the installation site, condensation due to differences between the
internal and external temperatures can be anticipated on the magnetic surface of the disk unit,
wait for the unit to be sufficiently acclimatized to the indoor environment before turning it on.
ANNT) Notes on handling the unit
The components mounted in the unit are sensitive to mechanical forces and static electricity.
When handling these components, take the following precautions.
- Before handling the unit, ground it and then wear a wrist strap to ground your body.
- To extract a component from the unit, extract it from the unit placed on a static dissipative
mat laid out on a flat workbench before starting to work on it.
- After removing a unit from the system board, store it in an antistatic bag.
ANNT) Notes on using an antistatic bag
- Make sure that the antistatic bag is not ripped or torn.
- Confirm that no part of the unit sticks out from the antistatic bag.
- When the opening of the antistatic bag is folded, the fold must be at least 30 mm.
ANNT) Antistatic measures for connecting twisted pair cables for LAN
When connecting a twisted pair cable for LAN to a device, ensure the following measures are
fully taken to avoid the risk of equipment destruction caused by electrostatic discharge:
(1) Before connecting twisted pair cables, first connect the modular connector to the specified jig,
and then bring the end of the jig cable into contact with the FG for at least one minute
to remove any static electricity from the cables. (Tool name: LAN cable ESD tool.)
(2) After the electro-static discharging is finished, promptly connect the twisted pair cable to
the equipment.
(3) Connect the cables to the building ground, power system FG,
and water pipe whenever possible, and avoid connecting them to the FG of the
electronic equipment.
(4) When using the power system FG, be careful to avoid any short-circuiting with
the AC power supply.

14
<Detail of static-electricity removal from twisted pair cables>
The time required to remove static electricity is over one minute.
Outline drawing of LAN cable ESD tool
RMRK) Body grounding
When connecting a twisted pair cable, wear a wrist strap to ground your body, just as when
handling printed circuit assemblies.
ANNT) Connecting a twisted pair cable to a network environment
Do not connect a twisted pair cable to network devices such as a hub in the customer's network
environment until the completion of its setup. (This precaution helps avoid a possible network
failure triggered by network congestion.)
ANNT) Connecting cables
To prevent incorrect cable connections, affix a "destination label" to the cable and cabinet.
See Appendix H “Prevention of Improper Cable Connections”
SET0102000
1.2 Preparing Tools for Installation
This section covers the tools, measuring instruments, test program, references, and other items to be
prepared in advance.
SET0102010
1.2.1 Tools and measuring instruments
“Table 1.2.1” lists the tools and measuring instruments to be prepared in advance.
Table 1.2.1
Tool or measuring instrument name
Remarks
General tool set for maintenance worker
FST (PC for maintenance worker)
Wrist strap
LAN cable ESD tool
LAN straight cable in category 5 or higher
Digital voltmeter
Cable labels
To prevent incorrect cable connections
Cable labels with ties
To prevent incorrect cable connections

15
SET0102020
1.2.2 Configuration and setting information
“Table 1.2.2” lists the information to be obtained in advance from the sales representative or SE in
charge.
Verify the information got in advance.
Table 1.2.2
Configuration and setting information
Remarks
Installation Instructions Sheet
This sheet provides such customer-specified information as
IP addresses and passwords provided through sales/SE
departments.
SET0103000
1.3 Checking Installation Requirements
This section describes requirements for installing the Base Unit.
If you find any problems, contact the related department and take appropriate action.
SET0103010
1.3.1 Environmental requirements
Confirm that the environmental requirements for installing the system fall within the range listed in
“Table 1.3.1-1”.
To make sure the operating environments are satisfied, check them when the system is operating.
Table 1.3.1-1 System environmental requirements
Operating
Non-operating
Temperature
[
o
C]
Humidity
[%RH]
Temperature
[
o
C]
Humidity
[%RH]
5 to 35 (without ATD)
5 to 40 (with ATD)
20 to 80
0 to 50
8to 80
ANNT) The temperature requirements depend on the altitude of the installation location.
- When the system is installed at an altitude of 0 to 1000 m (0 to 3,281 ft.) above sea
level: 5 to 40 oC (41 to 104.0 oF)
- When the system is installed at an altitude of 1,000 to 1,500 m (3,281 to 4,921 ft.) above sea
level: 5 to 38 oC (41 to 100 oF)
- When the system is installed at an altitude of 1, 500 to 2,000 m (4, 921 to 6,562 ft.) above sea
level: 5 to 36 oC (41 to 96.8 oF)
- When the system is installed at an altitude of 2,000 to 3, 000 m (6,562 to 9, 843 ft.) above sea
level: 5 to 33 oC (41 to 91.4 oF)
The service engineer department should make the following checks related to environmental
requirements.
If there is a problem with the installation environment, ask the customer to implement the required
improvements.
- Measure items related to the installation environment (humidity and leakage current).
- Check the installation conditions (location, computer room, power supply facility,
and air conditioning).
- Confirm that the cold air flow from air conditioning and the hot equipment exhaust do not collide,

16
resulting in a degraded cooling effect.
- Check the operation conditions (operating time, system and facility ON/OFF control methods,
extent of disaster handling facilities, etc.)
“Table 1.3.1-2” lists the specific check items and examples of failures that occurred in the past.
Table 1.3.1-2 Check items and examples of past problems
Environmental
condition
Check item
Example of failure
Dust
There should be no electric conductive
matter such as concrete particles or
iron dust under the device floor.
There was a large amount of iron dust
under the device floor, some of which
penetrated the unit and triggered a
failure. Numeral parts had to be replaced.
There should be no foreign matter that
may clog the filter.
A plastic bag on the floor was drawn
in and ended up clogging the filter.
Parts were damaged due to the
resulting rise in temperature.
Temperature
and humidity
The temperature, relative humidity,
and maximum wet-bulb temperature
gradient should comply with the
specifications.
The power could not be turned on
because of high humidity levels in
a new building.
The room temperature should be evenly
maintained throughout the room.
A temperature alarm was triggered
because heat was not dissipated,
because of the poor layout of the air
conditioning for the units.
A sufficient amount of cool air should
be provided through the floor outlets.
-
There should be sufficient clearance
under the device floor.
The temperature rose because cables
under the device floor were blocking
the air conditioning inlets.
Air conditioner
The air velocity should be even.
The air velocity was unusually high
because of installation next to an air
conditioner, which generated an air
wall inside the unit. This caused
the temperature to rise, which in turn
triggered an alarm.
Humidifier
Only pure water should be used for
ultrasonic humidifiers.
There was a buildup of a white residue
because of the use of tap water, which
resulted in a failure caused by leakage.
SET0103020
1.3.2 Input power
Confirm the allowable range of input power supplied to the Base Unit. (See “Table 1.3.2”.)
Table 1.3.2 Input power requirements
Input power voltage
Frequency
200 to 240VAC ±10% single phase
50/60Hz +2%/-4%

17
SET0103030
1.3.3 Input power system
- For the power shutoff feature of the circuit breakers, see Appendix B “Customer's Distribution Panel
Breaker Requirements”.
Also confirm the connection configuration of the customer distribution panels and check the power
outlet shapes and power shutoff feature of the circuit breakers.
- For the power outlet shapes, see Appendix C “Plug Types”.
- For connection configurations for customer distribution panels, see "Table 1.3.3".
Table 1.3.3
Amount of PSU
Refer to "Input Power Systems"
2
See Appendix D.1 “2 PSUs”
3
See Appendix D.2 “3 PSUs”
4
See Appendix D.3 “4 PSUs”

18
SET0103040
1.3.4 Installation area
Confirm installation area when 19-inch rack mounted.
Figure 1.3.4

19
SET0104000
1.4 Setting the FST
This chapter describes setting the FST used for installation.
(1) Web browser
Figure 1.4-1
Figure 1.4-2 Compatibility View Settings
RMRK) If Internet Explorer v11 cannot be used, the following web browsers can be used.
When the following browsers are used, the setting of a browser like Internet Explorer v11 is not
needed.
- Microsoft Edge Browser
- Google Chrome v50 and higher version
- Firefox v46 and higher version

20
SET0105000
1.5 Request to system administrator
Request the following items to the system administrator.
(1) Get iRMC connection information.
The server has no maintenance dedicated LAN port.
It is necessary to connect FST with the network switch port according to the network
environment. See Appendix E.1 “Operation terminal connection” for details.
(2) Confirm unit location and quantity with installing to the system administrator.
(3) When the BitLocker function enable, request to suspend the BitLocker function.
(4) When the BIOS password enable, request to disable the BIOS password.
(5) When expansion of unit cannot work possible in the state of system power on,
request system power off.
(6) When the [Email Alerting] function enable, request to the disable it.
(7) Obtain the permission of the use of the Video Redirection (HTML5) to the system administrator.