Numatic WVDP 1800-2 Specifications

Please take care when unpacking this appliance as some of the parts may be heavy.
1) Lift out the top fitting complete with all accessories and place to one side.
2) Lift out middle fitting and place to one side.
3) Lift off head assembly complete with mains cable and place onto the floor.
4) Lay the main packaging box down and gently slide the drum assembly out of
the packaging, ensure the drum assembly is upright once out of the box.
5) Fit head assembly onto drum assembly and secure in place using the hooked
knobs fitted to the drum assembly.
Please ensure the following items been included;
•1 x WVDP 1800-2 PH Pond Vacuum
•1 x 1800 drum handle assembly
•1 x 601101 2.5mtr hose
•1 x 601027 Stainless Steel bend
•1 x 601328 Pick up nozzle with blades(for working on the pond floor)
•1 x 601428 Pick up nozzle with brushes (for removing blanket weed from the
pond floor)
•1 x 601141, 1 x 601145, and 1 x 601146 accessory kit (for cleaning the pond
sides)
•4 x 601008 Stainless Steel Extension Tubes
Important Note
Before using this vacuum around the pool side, it is strongly recommended that an R.C.D unit is
fitted in between the mains plug from the vacuum and the wall socket.
Instructions:
1. Connecting the machine together:
•Fit drum handle into the slots on the sides of the drum assembly, use a pozi drive
screwdriver to remove the pozi screws before fitting the handle. Refit screws and
tighten once the handle is in place.
•Connect the vacuum hose to the hose flange on the front of the vacuum.
•Assemble the wand sections and connect to the vacuum hose.
•Fit either the pick up nozzle with blades/ brushes to the wand section.
•Uncoil the dump hose assembly on the rear of the vacuum into a suitable drain or
onto the garden, the hose is 3 metres in length)
•Open the slide valve on the curved wand section fully.
•Connect the vacuum to the mains power supply ensuring an R.C.D is fitted
between the mains plug and mains socket.
WVDP 1800-2 Pond Vac
Operator Instructions

2. Cleaning the bottom of the pond:
•Place the wand section into the pond/pool and switch on the vacuum.
•With the slide valve fully open minimal amounts of waste will be removed from
the pond/pool bottom, for best results set the slide valve half way. If heavy
deposits are found on the pond/pool bottom, close the slide valve.
•Please note: That when picking up heavy deposits that contain large amounts of
blanket weed and debris, all waste will be collected in the filtration basket fitted
inside the vacuum. The basket will need to be emptied if you are picking up a lot
of waste. 3. Cleaning the sides of the pond:
•To use the vacuum to clean the sides of the pond, connect the curved wand section
onto the hose end cuff.
•Connect the accessory kit to the end of the curved wand section, or if working at a
greater depth add the straight wand sections accordingly.
•Ensure the slide valve is fully open on the wand section, turn on the vacuum and
place into the pond; scrub the pond sides to remove algae and grime.
•4. Emptying the machine:
•When the vacuum is full of contaminated pond water note that the pitch of the
motors will change, and water will no longer be picked up by the vacuum.
•To empty the vacuum, ensure the dump hose assembly is fully uncoiled from the
back of the vacuum.
•Turn on the green pump switch fitted to the handle assembly of the vacuum
cleaner.
•Please note: that the barrel filter fitted to the pump assembly will need to be
removed and cleaned on a regular basis. The filter is found inside the drum
assembly of the vacuum and is coloured white.
•5. Things to remember:
•This vacuum is intended only for the use of cleaning ponds or swimming pools.
•The vacuum should be securely placed next to the pond so as not to slip or to be
pulled in when being used.
•The vacuum should not be used for the removal of Hazardous or Volatile
substances.
•Do not allow children near the pond when using the pond vac or let them use the
machine.
•Never use this vacuum in or around the pond unless you have a Residual
Current Device Fitted (R.C.D)
The manufacturer of this appliance cannot accept responsibility for loss of stock or
damage to ponds while using this product.