NXP Semiconductors KEA128LEDLIGHTRD User manual

KEA128LEDLIGHTRD
Quick Start Guide
Lighting Control Module Reference
Design using Kinetis KEA128

2
Quick Start Guide
6 Pin SWD
_
+
12 V Power
Supply
User Buttons
Reset Button
Kinetis EA
MCU
MC10XS3425
Driver
User LEDs
Light Output
Connector
Potentiometers
CAN
Connector
LIN
Connector
MC33662 LIN
Transceiver
MC33901 CAN
Transceiver
Figure 1: Front side of KEA128LEDLIGHRD
Get to Know the KEA128LEDLIGHTRD Board

3
freescale.com
KEA128LEDLIGHTRD Features
Hardware
• SKEAZ128 32-bit ARM
®
Cortex
®
-MO+
MCU (64-pin LQFP)
• MC33662 LIN transceiver
• MC33901 CAN transceiver
• MC10XS3425EK multi-chip high-side
switch
• 4 LEDs
• 4 Potentiometers
• 4 User buttons
• SWD connector interface for debugging
• Light connector interface

4
Step-by-Step
Installation Instructions
1Install CodeWarrior
Development Studio
CodeWarrior Development Studio for
Microcontrollers installation file is included
in the supplied media for your
convenience.
The most recent version of CodeWarrior
for MCUs (Eclipse IDE) can be downloaded
from www.freescale.com/CodeWarrior.
2Install
FreeMASTER
FreeMASTER run-time debugging tool
installation file is included on the supplied
media for your convenience.
For FreeMASTER updates, please visit
freescale.com/FreeMASTER.
Download
Application Software
Download and install the reference design
application software available at
freescale.com/KEA128LEDLIGHTRD.
4Connect a
Lamp
Connect up to 4 lamps in to the light
output connector of the board.
Connect the
Power Supply
Connect the 12 V power supply to the
power supply terminals.
Quick Start Guide
3
5

5
Step-by-Step Installation
Instructions (cont.)
Connect the
Debugger
Connect a P&E USB Multilink Universal
debugger to the 6 pin SWD connector
of the board. Both LEDs on the P&E
debugger must turn on.
7Reprogram the MCU
using CodeWarrior
Development Studio
Import the downloaded reference design
application project in the CodeWarrior
Development Studio:
1. Start the CodeWarrior application.
2. Click File – Import.
3. Select General – Existing Projects
into Workspace.
4. Select “Select root directory” and
click Browse.
5. Navigate to the extracted application
directory: KEA128LEDLIGHTRD/
KEA128_LIGHTING_RD and click OK.
6. Click Finish.
7. Click Run>Debug to download the
code to the KEA128. This starts the
launching progress until the debugger
perspective appears and stops at the
line of main () in the source view. Click
on the stop button.
FreeMASTER
Setup
1. Start the FreeMASTER application.
2. Open the FreeMASTER Project
KEA128LEDLIGHTRD/KEA128_
LIGHTING_RD/KEA128LIGHTING.pmp.
3. Click the red STOP button in the
FreeMASTER toolbar or press Ctrl+K to
enable the communication.
freescale.com
6
8

6
Quick Start Guide
Application Control in FreeMASTER
The FreeMASTER run-time debugging tool is used to control the application and
monitor application variables during run-time. An explanation on how to use the
FreeMASTER user interface is given below.
1. Click the Output Control button in the Output Channel section or press
switch SW2, SW3, SW4, SW5 to control each output state. The output states
are OFF, ON or TOGGLE.
2. To change the PWM duty cycle of the outputs using only the FreeMASTER
sliders, click in the FreeMASTER PWM Control button located in the General
Settings section. Button must be in ON state. When button state is OFF the
duty cycle of the outputs can be controlled only using the potentiometers R18,
R89, R90, and R91.
3. Change the PWM duty cycle of the outputs by moving the PWM Duty Cycle
slider of each output.
4. In case of an output fault, the corresponding fault label will turn red in the
Diagnostic and Status Flags section of each output.
5. General faults flags and operation mode of the system are indicated in the
General Settings section. By default the operation mode is Normal Mode.
6. In case of an under voltage fault, stop the FreeMASTER communication by
clicking the red STOP button. Remove the under voltage condition. Start the
FreeMASTER communication by clicking the red STOP button. The Fault
Status and the Under Voltage label will turn red and the outputs will be off.
To remove this fault click on the Clear Under Voltage Fault button or press
any switch SW2, SW3, SW4, SW5 on the board, to return the system to its
Normal Mode.

7
freescale.com
Headers and Connectors List
Header/Connector Description
J1 12 V DC power input terminals
J2 Kinetis KEA128 Serial Wire Debug (SWD) header
J14 LIN physical interface signal header
J15 CAN physical interface signal header
J6 Lights output connector
Jumper Options
Jumper Option Setting Description
J4 Inputs
1-2
Allows independent control of each high side switch output
4-5
7-8
10-11
J3 Wake up 1-2 Allows wake up function of MC10XS3425
J5 FSI 2-3
FSI selection:
1-2: FSI terminal connected through 6.8 kOhm resistor to ground
2-3: FSI terminal connected to ground
The following is a list of all jumper options. The default installed jumper settings
are shown in white text within gray boxes.

For more information, visit
freescale.com/KEA128LEDLIGHTRD
Freescale, the Freescale logo, CodeWarrior and Kinetis are trademarks of
Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or
service names are the property of their respective owners. ARM and Cortex
are registered trademarks of ARM Limited (or its subsidiaries) in the EU and/or
elsewhere. All rights reserved. © 2014 Freescale Semiconductor, Inc.
Doc Number: KEA128LEDLIGHTQSG REV 0
Agile Number: 926-28450 Rev A
Support
Visit freescale.com/support for a list of phone
numbers within your region.
Warranty
Visit freescale.com/warranty for complete
warranty information.
Get Started
Download installation software and documentation under
“Jump Start Your Design” at freescale.com/CodeWarrior.