Nylex 701078 User manual

Install a new hose on the reel: Continued
2. Replace the original cable tie just back from
the barb with a new one as this secures the hose
attachment from unnecessary stress during full
extension. Fig.15
3. Carefully let the hose rewind over the drum,
helping if necessary by gently pushing down on
the foot pedal. Fig.16
4. When the new hose is wound over the drum,
remove the hose-stop ball from the old hose and
install on the new hose approximately 1m from
the end of the hose Fig.17.
5. Reattach a hose connector and trigger gun.
(Fig.18) – the installation is now complete!
GUARANTEE
Cyclone Tools Pty Ltd guarantees the Hose Reel and Hose Fittings
for 2 years and the Hose for 12 years from the date of purchase.
If the relevant product proves defective as to materials or workmanship within that period, Cyclone
Tools Pty Ltd will, at its option either replace or refund the purchase price for the relevant product.
In the event of such a defect, the product should be returned to the place of purchase, together with
proof of purchase, for replacement or refund. Any handling and transportation and other expenses
incurred in claiming under this warranty) are not covered by this warranty and will not be borne by
Cyclone Tools Pty Ltd.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if goods fail to
be of acceptable quality and the failure does not amount to a major failure. The benets given by this
guarantee are in addition to other rights and remedies which may be available to the consumer under
SPECIFICATIONS
Model 701078
Hose Length 30m
Type of Hose PVC
Working Pressure 150psi
I.D of Hose 12mm
Material of Outer Casing PP
Size of Inlet and Outlet 12mm
Fig.17 Fig.18
Fig.15
Eortless Foot Pedal Retraction
Fig.16
FOOT PEDAL HOSE REEL
Owner’s Manual - 701078
Made in China to strict Nylex quality standards.
www.cyclone.com.au
Cyclone Tools Pty Ltd317 Abbotts Road, P.O. Box 4339 Dandenong South, Victoria 3175, Australia.
The Nylex brand is licensed to Cyclone Tools Pty Ltd by Wet Technologies Pty Ltd.

5. WHEN USING THE HOSE REEL PLEASE NOTE THE FOLLOWING:
1. Place on a level surface when operating the unit.
2. Do not operate the foot pedal when pulling out the hose – this will cause damage to the mechanism.
3. When pulling the hose out, slow down toward the end to avoid damage to the connection point.
4. When rewinding the hose, rst bring the trigger gun end of the hose up toward the unit to avoid
damage to the trigger gun by dragging it along the ground - this will also make retraction an
easier process.
5. When using the foot pedal to retract the hose, reduce foot pedal force toward the end of retraction
to avoid strain on the trigger gun connection.
6. Every so often, completely pull out all 30 meters of hose, release any kinks or twists and then
gently retract the hose again
6. MAINTENANCE
1. When not in use, turn o the water at the tap and squeeze the nozzle trigger to release
the water pressure.
2. Do not use the hose or unit to transmit anything other than water (chemicals or solvents for example).
3. When not in use for long periods of time, it is advisable to store your reel out of the weather.
7. ELIMINATING THE POSSIBILITY OF HOSE REEL MALFUNCTION
1. In the process of retracing the hose, if the hose locks, go to the front of the unit and gently pull out some hose
to unlock the mechanism.
2. If the hose locks during the process of pulling it out, go to the rear and gently depress the foot pedal to unlock the mechanism.
8. INSTRUCTIONS FOR REPLACING THE HOSE
Remove the existing hose from the reel:
1. Unfold the handle.
2. To remove the original hose, pull it from the reel
using one hand to steady the unit and the other hand
to pull on the hose Fig10.
3. Using protective gloves, hold one side of the reel
drum to avoid it winding, cut and remove the plastic
cable tie, unscrew the hose clamp and gently remove
the hose from the plastic barb. If dicult to remove,
simply slice the last 50mm of the hose with a sharp
blade in a lengthwise direction. Fig.11.
Note: By pulling out the original hose, the spring in
the hose drum will want to rewind. To avoid injury,
wear gloves when holding the reel. Fig. 10 & 11
Install a new hose on the reel (Max. capacity 30m):
1. Remove the old hose taking note how it enters
the body through the front orice. Fig.12. Thread
your new hose up to the drum. Slip the original
hose clip over the end of the new hose and push
the end of the hose onto the drum barb and
tighten. Fig.13 & 14.
Continued following page.
FOOT PEDAL HOSE REEL OWNER’S MANUAL - 701078
4. HOW TO USE THE REEL
1. Unfold the handle by lifting it upwards until
the locking button pops out.
Fig.4 a & b
2. To lower the handle for storage,
depress the locking button on each side of the
reel and tilt the handle forward again. Fig.5
3. When moving the hose reel, pull it
toward or behind you - don’t push it
forward. Fig. 6
4. The trigger gun is located on the unit as
shown. Fig.7 (opposite page)
5. To pull out the hose, grasp the hose stop and
remove as much hose as needed by pulling at an
even speed. When you have removed as much
hose as you need, it will self-lock. Fig.8
6. To retract the hose, stand at the rear and
holding the handle, use your foot to depress the
pedal repeatedly. Using a longer pedal motion
each time is more ecient. Fig.9
1. INTRODUCTION
The Nylex Foot Pedal Hose Reel is ideal for neatly storing and protecting your hose
from the harsh Australian sun. The unit has been designed for maximum mobility
and can be moved to any part of your garden, front or rear, as long as you have access to a tap.
The hose can be easily pulled out, extracting as much hose as you need and can be just
as easily retracted by pumping the convenient foot pedal.
2. PARTS LIST
A. 1 Foot Pedal Hose Reel Unit.
B. 2 Wheels
C. 1 Inlet Hose 2M (6.56ft) with Connectors
D. 1 Trigger gun
E. 1 Foot pedal hose reel stand
Fig.2
Fig.4a
Fig.5
Fig.8
Fig.3
Fig.4b
Fig.6
Fig.9
Fig.12
Fig.10 Fig.11
Fig.13
Fig.7
Foot Pedal
Handle
Trigger Gun &
Hose Fittings
Hose Stop
Case
3. INSTALLATION
1. Install the wheels to each side of the hose
reel by placing the wheel on the wheel axle,
inserting the washer and locking pin and
then placing the cover on the wheel. Fig. 2
2. Attach the foot pedal hose reel stand to the
unit by inserting the two (2) metal poles into
the plastic cover near the bottom of the
unit. Fig. 3
3. Install the Tap to Reel inlet hose on the body
of reel.
Foot Pedal hose reel stand
Fig.14