Nyne N-19 User manual

FR
ES
EN
User Manual.................... 3
Manual del usuario ...... 27
Manuel utilisateur......... 51
nyne.com
All registered and unregistered trademarks are
property of their respective owners.
Nyne Multimedia Inc.
All rights reserved.
Série Alarme
FR
Series de alarma
ES
Alarm Series
EN
N-19
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 1
4/6/2012 11:06:59 PM

NYNE_N-19_User Manual_A6_V1.1_20120406.indb 2
4/6/2012 11:06:59 PM

English
3
EN
Contents
1 Important 4
Safety 4
Notice 6
2 Introduction 9
Overview 10
3 Preparation 13
Unpack 13
Connect power 13
Connect the AM loop antenna 13
Turn on the device 13
Get the remote control ready for use 14
Activate the backup battery 14
4 Operation 16
Set clock 16
Play and charge your iPod/iPhone/iPad through the device 18
Listen to FM or AM radio stations 20
Listen from an auxiliary device 22
Adjust brightness of LED display 22
5 Specifications 23
6 Frequentlyaskedquestions(FAQ) 24
Contents
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 3
4/6/2012 11:06:59 PM

4EN
1 Important
Safety
The lightning ash
with arrowhead
symbol within
an equilateral triangle is
intended to alert the user to
the presence of un-isolated,
dangerous voltage within the
inside of the device that may
be of sufcient magnitude
to constitute a risk of electric
shock to persons.
The exclamation
point within an
equilateral triangle
is intended to alert the user
to the presence of important
operating and servicing
instructions in the literature
accompanying the device.
Read these instructions before
operation.
Keep these instructions for
future reference.
Follow all instructions
for installation, use and
maintenance of the device.
To avoid tilt or drop, place
the device on a at and hard
surface.
To clean the device,
disconnect power rst. Clean
only with soft and dry cloth.
To ensure compatibility, only
use accessories recommended
by the manufacturer.
When the device is suddenly
moved from cold to warm
surroundings, condensation
may form in the housing
of the device. Before use,
leave the device in the warm
environment until the moisture
evaporates.
Keep the device away
from heat sources, such as
a radiator, heater, oven,
amplier, naked ames or
direct sunlight.
Never block any ventilation
openings.
• Do not expose the device
to sand or dust, or cover
it with items, such as
newspapers, table cloths, or
curtains.
• Do not operate the device
in an enclosed cabinet.
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 4
4/6/2012 11:06:59 PM

English
5
EN
Leave sufcient free space
around the device for
adequate ventilation.
Keep the device away from
moisture. Never expose the
device to rain, dripping or
splashing. If water penetrates
into the device, unplug the
power cord and contact your
dealer. Continuous use in
this case may result in re or
electric shock.
Make sure that the power
supply voltage is within the
range indicated on the label
on the device or power
adapter. If you are not sure
of the type of power supply,
consult you dealer or local
power company.
Do not defeat the safety
purpose of the polarized
or grounding-type plug. A
polarized plug has two blades
with one wider than the other.
A grounding type plug has two
blades and a third grounding
prong. The wide blade or the
third prong is provided for your
safety. If the provided plug does
not t into your outlet, consult
an electrician for replacement
of the obsolete outlet.
When connected to a power
outlet, power is always owing
into the device. To completely
disconnect power, unplug the
power cord.
When you unplug the power
cord, always hold the plug
instead of the cord.
Do not overload power
strips and extension cords.
Overloading can result in re or
electric shock.
The wall socket should be
located near the device and
be easily accessible.
Where the mains plug or an
appliance coupler is used as
the disconnect device, the
disconnect device shall remain
readily operable.
During lightning storms or when
the device is not to be used for
a long period of time, always
unplug the power cord of the
device. Pulling on the power
cord can damage the wires
inside the cord and may cause
re or electric shock.
Do not attempt to repair or
service the device yourself.
Opening or removing the
cabinet may expose you
to electric shock, and other
hazards. If repair is required,
contact your dealer and refer
all servicing to qualied service
personnel.
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 5
4/6/2012 11:07:00 PM

6EN
Do not use the device if any
abnormality occurs. If any
smoke or odor becomes
apparent, unplug the power
cord and contact your dealer
immediately. Do not try to
repair the device yourself.
Avoid using dropped or
damaged appliances. If the
device is dropped and the
housing is damaged, the
internal components may not
function normally. Unplug the
power cord immediately and
contact your dealer for repair.
Continued use of the device
may cause re or electric shock.
Before moving the device,
make sure to disconnect the
power cord and any other
cables rst.
To reduce the risk of electric
shock, do not touch any
connector with wet hands.
Never remove the housing of
the device.
Never lubricate any part of the
device.
Never place the device on
top of any other electrical
equipment.
Button cell batteries are
dangerous if swallowed! Keep
batteries out of the reach of
children.
Notice
Modification
Any modication (such
as removing the speaker
grill) to the device, without
prior authorization from the
manufacturer, may void your
warranty and authority to
operate the device.
FCCcompliancestatement
This equipment has been
tested and found to comply
with the limits for a Class B
digital device, pursuant to
part 15 of the FCC Rules.
These limits are designed to
provide reasonable protection
against harmful interference
in a residential installation.
This equipment generates,
uses, and can radiate radio
frequency energy and,
if not installed and used
in accordance with the
instruction manual, may cause
harmful interference to radio
communications. However,
there is no guarantee that
interference will not occur
in a particular installation. If
this equipment does cause
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 6
4/6/2012 11:07:00 PM

English
7
EN
harmful interference to radio
or television reception, which
can be determined by turning
the equipment off and on,
the user is encouraged to try
to correct the interference by
one or more of the following
measures:
• Relocate the receiving
antenna.
• Increase the separation
between the equipment and
receiver.
• Connect the equipment into
an outlet on a circuit different
from that to which the receiver
is connected.
• Consult the dealer or an
experienced radio/TV
technician for help.
Thisdevicecomplieswith the FCCRules.
Operation is subject to the
following two conditions:
1 This device may not cause
harmful interference, and
2 This device must accept
any interference received,
including interference
that may cause undesired
operation.
Recycling
Packaging
Observe the local regulations
for how to dispose of the pack-
aging materials.
Oldproductandbattery
The old product shall not be
treated as household waste.
Observe the local regulations,
and send the old product
and battery to the applicable
collection point for recycling
of electrical and electronic
products and batteries. Correct
disposal of such products
helps prevent potentially
negative consequences on
the environment and human
health. For more information,
consult your local authority or
dealer.
Copyright
“Made for iPod”, “Made for
iPhone”, and “Made for iPad”
mean that an electronic
accessory has been designed
to connect specically to iPod,
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 7
4/6/2012 11:07:00 PM

8EN
iPhone, or iPad respectively,
and has been certied by
the developer to meet Apple
performance standards.
Apple is not responsible for
the operation of this device
or its compliance with safety
and regulatory standards.
Please note that the use of this
accessory with iPod, iPhone,
or iPad may affect wireless
performance.
iPhone, iPod nano, and iPod
touch are trademarks of Apple
Inc., registered in the U.S.
and other countries. iPad is a
trademark of Apple Inc.
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 8
4/6/2012 11:07:00 PM

English
9
EN
2 Introduction
Thank you for purchasing our
product.
This is a clock radio speaker
system that allows you to:
• Wake you up at a preset time,
with the built-in buzzer (AUX),
radio broadcast, or music from
your docked iPod/iPhone/
iPad.
• Dock and charge your iPod/
iPhone/iPad.
• Play music from your docked
iPod/iPhone/iPad.
• Play video from your docked
iPod/iPhone/iPad on the large
screen of a TV connected to
the device through S-Video
connection.
• Tune and listen to your favorite
AM/FM radio stations.
• Play music from a connected
auxiliary device.
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 9
4/6/2012 11:07:00 PM

10 EN
Overview
Mainunit
1Dock cover
• Lift up to support the
docked iPod/iPhone/iPad.
• Close to protect the dock
connector.
2Dock for iPod/iPhone/iPad
3
• Turn down volume.
• Adjust time during clock or
alarm setting.
• Select an alarm source dur-
ing alarm setting.
4
• In dock mode, pause or
resume music/video play.
5/
• In dock mode, skip to the
previous or next song.
• In AM/FM tuner mode, tune
to a radio station.
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 10
4/6/2012 11:07:01 PM

English
11
EN
6
• Activate or deactivate
alarm 1 (if set).
7LED screen
• Display information about
the current status of the
device.
8
• Activate or deactivate
alarm 2 (if set).
9Preset
• In AM/FM tuner mode, tune
to a preset radio station.
0Set
• Conrm a setting or selec-
tion.
!Source
• Select the time source or
an audio source (dock, AM,
FM, or AUX).
• Cancel clock or alarm
setting.
@
• Turn up volume.
• Adjust time during clock or
alarm setting.
• Select an alarm source dur-
ing alarm setting.
#Snooze
• When a set alarm rings,
press to turn off the alarm
for an interval of nine
minutes.
• When a set alarm rings,
press and hold to stop alarm
ringing for the current day.
• In time mode, press to
adjust brightness of the LED
display.
$Power on/off
• Turn on or off the device.
%DC in
• Connect the power adapter.
^S-Video
• Connect an S-Video cable
(not supplied) to a TV.
&AUX in
• Connect an auxiliary
device.
*AM ANT
• Connect the supplied AM
antenna.
(Radio EU/US
• Switch between the EU and
US frequency steps.
)FM antenna
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 11
4/6/2012 11:07:01 PM

12 EN
Remotecontrol
1Source
• Select the time source or
an audio source (dock, AM,
FM, or AUX).
• Cancel clock or alarm
setting.
2/
• In dock mode, skip to the
previous or next song.
• In AM/FM tuner mode, tune
to a radio station.
SourceSet
3
• Turn up/down volume.
• Adjust time during clock or
alarm setting.
• Select an alarm source dur-
ing alarm setting.
4Alarm 1/2
• Activate or deactivate
alarm 1 or 2 (if set).
5Snooze
• When a set alarm rings,
press to turn off the alarm
for an interval of nine
minutes.
• When a set alarm rings,
press and hold to stop
alarm ringing for the current
day.
• In time mode, press to
adjust brightness of the LED
display.
6Numeric keys
• Select a preset radio station
directly.
7
• In dock mode, pause or
resume music/video play.
8Set
• Conrm a setting or selec-
tion.
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 12
4/6/2012 11:07:01 PM

English
13
EN
3 Preparation
Unpack
Unpack and identify the items
of your package.
• 1 x clock radio speaker
• 1 x remote control
• 1 x power adapter
• 1 x 3.5mm audio cable
• 1 x AM loop antenna
• 1 x User Manual
• 1 x Quick User Guide
• 1 x warranty card
Connectpower
Connect the supplied power
adapter:
• round connector to the DC
in socket on the back of
the device
• power plug to the wall
socket
ConnecttheAMloop
antenna
1 Assemble the supplied AM
antenna.
2 Connect the AM antenna
to the socket on the back
of the device.
Turnonthedevice
Slide the Power on/off switch on
the back of the device to the
left.
+The display panel lights up.
AM
ANTENNA
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 13
4/6/2012 11:07:02 PM

14 EN
Toturnoffthedevice:
• Turn the Power on/off switch
to the right.
Gettheremotecontrol
readyforuse
Warning:
• To reduce the risk of explo-
sion, keep batteries away
from heat, sunshine, or re.
• To reduce the risk of dam-
age, remove the battery
when the remote control
is not to be used for a long
period of time.
Remove the protective tab on
the battery cover at the back
of the remote control.
Toreplacetheremotecontrolbattery:
1 Remove the battery cover.
2 Replace the old battery
with a new one (type:
CR2025) with the correct
polarity.
3 Mount the battery cover
securely.
Activatethebackupbattery
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 14
4/6/2012 11:07:02 PM

English
3 Mount the battery cover
securely.
15
EN
Remove the protective tab on
the battery cover at the bot-
tom of the device.
Tips:
• The backup battery is used
for storage of the set clock
and alarm in cases of
power interruption.
• If no backup battery is
loaded or the battery is
used up, you need to set
the clock and alarm again.
Toreplacethebackupbattery:
1 Unscrew the battery cover
at the bottom of the de-
vice.
2 Replace the old battery
with a new one
(type: CR2025) with the
correct polarity.
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 15
4/6/2012 11:07:03 PM

16 EN
4 Operation
Setclock
Setclockautomatically
Note:
• If you have a protective
case on your iPod/iPhone/
iPad, you may need to
remove it rst.
1 Lift up the dock cover.
2 Connect your iPod/
iPhone/iPad to the dock
connector on the top of
the device.
+The clock time is synchro-
nized automatically from
your iPod/iPhone/iPad to
the device.
3 Adjust the angle of the
dock cover for optimal
support of your docked
iPod/iPhone/iPad.
Tosetalarmaftersynchronization:
1 Press Source repeatedly to
select the time source.
+The set clock is displayed
on the screen.
2 Press Set repeatedly until
is displayed at the upper
left corner of the screen.
3 Proceed with step 5 below
to set the alarm.
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 16
4/6/2012 11:07:04 PM

English
17
EN
Setclockandalarmmanually
You can also set the clock
and alarm at the same time
manually. Two wake-up timers
(alarm 1 and 2) are available,
which are helpful when you
and your family need to be
woken up at different time.
1 Press Source repeatedly to
select the time source.
2 Press Set to start setting.
+The hour digits start to ash.
3 Press / to adjust
the hour, then press Set to
conrm.
+The minute digits start to
ash.
4 Press / to adjust the
minute, then press Set to
conrm the clock setting.
+is displayed at the upper
left corner of the screen.
+The hour digits for alarm 1
start to ash.
5 Press / to adjust
the hour, then press Set to
conrm.
+The minute digits start to
ash.
6 Press / to adjust the
minute, then press Set to
conrm.
+A source icon ( iPod, AM,
FM, or AUX ) starts to ash
on the screen.
7 Press / to select a
source to wake you up,
then press Set to conrm.
+The volume level starts to
ash on the screen.
8 Press / to select the
volume level you like to
wake you up, then press Set
to conrm.
+is displayed on the
screen.
+The hour digits for alarm 2
start to ash.
9 Repeat steps 5 to 8 to set
the second alarm.
+Both alarm icons, the icons
of the respective alarm
sources, and the current
time are displayed on the
screen.
Tips:
• During clock or timer setting,
you can press Source at
any time to cancel the
operation and return to
clock display.
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 17
4/6/2012 11:07:04 PM

18 EN
• If you have selected dock
as the alarm source but
there is no iPod/iPhone/iPad
docked at the preset alarm
time, you will be woken
up with the built-in buzzer
instead automatically.
Todeactivateasetalarm:
In time mode, press or
once to deactivate alarm 1 or
alarm 2.
+The corresponding alarm
icon disappears.
Toactivateasetalarmagain:
In time mode, press or
again to activate alarm 1 or
alarm 2.
+The corresponding alarm
icon is displayed.
+The set alarm time, source
and volume level are
displayed briey.
Tips:
• When a set alarm rings, you
can press Snooze to turn off
the alarm for an interval of
nine minutes.
• When a set alarm rings, you
can press and hold Snooze
to stop alarm ringing. The
set alarm will ring again the
next day.
• If you have selected dock
as the alarm source, when
the corresponding alarm
rings, you can remove your
iPod, iPhone or iPad from
the dock to stop alarm
ringing. The set alarm will
ring again the next day.
• If a set alarm rings or
snoozes for more than half
an hour, the alarm will stop
ringing automatically and
ring again the next day.
PlayandchargeyouriPod/
iPhone/iPadthroughthe
device
You can play and charge
the following iPod, iPhone,
and iPad models through this
device:
Made for.
• iPad 2
• iPad
• iPhone 4S
• iPhone 4
• iPhone 3GS
• iPod nano (3rd, 4th, 5th, and
6th generation)
• iPod touch (3rd, and 4th
generation)
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 18
4/6/2012 11:07:04 PM

English
19
EN
Note:
• If you have a protective
case on your iPod/iPhone/
iPad, you may need to
remove it rst.
DockyouriPod/iPhone/iPad
1 Lift up the dock cover on
the top of the device.
2 Connect your iPod/iPhone/
iPad to the dock connector.
+The device switches to the
dock source automatically.
+The iPod icon is displayed at
the bottom of the screen.
+The device starts to charge
your iPod/iPhone/iPad.
3 Adjust the angle of the
dock cover for optimal
support of your docked
iPod/iPhone/iPad.
Playmusic fromyouriPod/iPhone/iPad
1 Start music play on your
iPod/iPhone/iPad.
2 Press / to adjust
volume.
3 Press or to skip to
the previous or next song.
4 Press to pause or resume
music play.
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 19
4/6/2012 11:07:05 PM

Toswitchtovideoplayonyour iPod/iPhone/iPad:
• Press and hold .
Toswitchbacktovideoplayon theTV:
• Press and hold again.
ListentoFMorAMradio
stations
Notes:
• In some regions, you may
need to change the
frequency step between
adjacent FM channels.
Slide the Radio EU/US
switch on the back of the
device to the left or right
to change the frequency
step between 200 kHz (US)
and 50 kHz (EU). After the
operation, you need to
power off and then power
on the device to activate
the setting.
• For optimal FM reception,
fully extend the xed FM
antenna at the back of the
device.
• For optimal AM reception,
adjust the direction and
location of the AM antenna.
PlayvideofromyouriPod/iPhone/iPad
1 Connect the device to a
TV with an S-Video cable
(not supplied).
2 Start video play on your
iPod/iPhone/iPad.
+The video is played on the
TV with sound output from
the clock radio speaker.
3 Press / to adjust
volume.
4 Press and hold or
to fast forward or back-
ward.
5 Press to pause or re-
sume video play.
20 EN
NYNE_N-19_User Manual_A6_V1.1_20120406.indb 20
4/6/2012 11:07:05 PM