O-SO Pure Mineral Mizer Manual

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 1 of 16
MINERAL MIZER
DEIONIZED WATER SYSTEM
INSTALLATION, OPERATION & SERVICE MANUAL

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 2 of 16
TABLE OF CONTENTS
INTRODUCTION ...................................................................................................................................... 3
Application .................................................................................................................................................................................3
BEFORE YOU BEGIN ................................................................................................................................ 4
Pu h-to-Connect (PTC) Fitting Primer .......................................................................................................................................5
Pre-in tallation Site In pection...................................................................................................................................................5
Pay Attention to All Warning ....................................................................................................................................................5
INSTALLATION GUIDE.............................................................................................................................. 6
Locate the Mineral Mizer............................................................................................................................................................6
Connect the Mineral Mizer to plumbing ....................................................................................................................................7
OPERATING THEORY ............................................................................................................................. 10
SERVICING YOUR MINERAL MIZER ......................................................................................................... 10
Schedule ....................................................................................................................................................................................10
Filter Stocking Strategie ..........................................................................................................................................................11
Changing Filter .........................................................................................................................................................................11
Sanitizing the Mineral Mizer.....................................................................................................................................................12
Materials required .......................................................................................................................................................12
Other requirements .....................................................................................................................................................12
Sanitization Procedure.................................................................................................................................................12
TROUBLE SHOOTING GUIDE................................................................................................................... 13
WARRANTY.......................................................................................................................................... 14
*THIS PAGE INTENTIONALLY LE T BLANK* ............................................................................................... 15
CERTIFICATE OF REFERRAL..................................................................................................................... 16
Redemption In truction & Re triction ..................................................................................................................................16
Di claimer ..................................................................................................................................................................................16

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 3 of 16
Definition
Within the context of this manual, we use the following
definitions:
•Deionized (DI) – water that is nearly free from ions,
the most common of which are metals (minerals)
and chlorides. DI water is roduced by filtration of
the source water.
•Mineral-free – water nearly devoid of all mineral
contamination.
•Total dissolved solids (TDS) – the mineral content of
a water sam le.
•Parts er million ( m) – the scale used to measure
mineral content of a water sam le.
•Distilled water – water that is mostly free from ions.
Distilled water is roduced by va orizing and
condensing the source water.
Warning
The DI water roduced by the Mineral Mizer is not
recommended for human consum tion. Although there
is no FDA warning concerning such consum tion, some
believe that mineral-free waters leach minerals from the
body. O-SO Pure makes no claims concerning the fitness
of the Mineral Mizer’s DI water for human consum tion.
The Mineral Mizer does not roduce bacteria-free water
nor does it attem t to sanitize or disinfect the water.
Feed water must be microbiologically safe.
Caution
The Mineral Mizer must be rotected against
•freezing tem eratures
•excessive heat
•excessive water ressure
•water hammer.
Failure to do so may result in breakage of water bearing
com onents and water leakage.
O-SO Pure recommends that feed water to the Mineral
Mizer be turned off when the office is unattended.
Introduction
Congratulations on your urchase of the Mineral Mizer autoclave water system. The Mineral Mizer roduces
deionized (DI) water from ta water, allowing you to exit
the boiled & bottled distilled water hamster wheel. When
routinely serviced, your Mineral Mizer will economically &
reliably deliver all of your DI water needs for years to
come.
The DI water roduced by the Mineral Mizer normally
registers at 000-002 arts er million ( m) on a handheld
total dissolved solids (TDS) tester.
A lications
Use the Mineral Mizer’s DI water for the following
a lications:
•Autoclave & Sterilizer – Scale formation in the boiler
is the leading cause of autoclave & sterilizer service
calls. Ta water causes film and scale that lead to
thermal inefficiency, increased maintenance and
downtime. Mineral Mizer’s DI water is even suitable
for sterilizers rogrammed to reject water when
mineral content exceeds a redetermined level.
•Iron and Steamer - Prevent scale buildu in
a liances that boil water by using DI water instead of
ta water.
•Di tilled water application - The DI water roduced
by the Mineral Mizer can be used for any a lication
calling for distilled water.
Now you can relax and enjoy the benefits of creating your
mineral-free DI water on-site. No more:
•strain & injury from carrying heavy bottles from
storage and lifting them onto dis ensers.
•tri s to the grocery store to urchase distilled water
bottles.
•waiting for the on-site distiller to dri out a gallon of
water while s inning the electric meter.
Your equi ment will benefit from the great water quality. Em loyees will love life without bottled water. You’ll
feel great about the green you save and the greening of your business by converting ta water directly into
mineral-free DI water.

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 4 of 16
Before You Begin
It is im ortant to correctly identify which Mineral Mizer model you are installing as this manual includes
instructions for all models.
Please take a moment to review this manual before roceeding with the installation.
Su lied Items Checklist
Take inventory of all items su lied to ensure none are missing. The box should contain the following:
Mineral Mizer Head Filter Spanner Wrench Filter Hou ing
Blue 3/8” Tube Feed Water Tube w Pre Reg- red drain tubing (bl ck) tank
Drain Saddle Angle Stop Valve chrome faucet
MODEL DESCRIPTION INSTALL IN TANK(S) DI WATER
DISPENSE
RO WATER
DISPENSE
DWS-SADI Mineral Mizer SC* or MR* steel 6 gallon red faucet Chrome faucet
DWS-SADI-D Mineral Mizer w/ attached gun SC* steel 6 gallon gun (15 ft) Chrome faucet
DWS-SADI-R Mineral Mizer w/remote dis ensing
gun
MR* steel 6 gallon remote gun
(15 ft)
Chrome faucet
*SC- sterilization center; MR- mechanical room

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 5 of 16
(OR)
Remote Di pen ing Gun Di pen ing Gun w Coiled Ho e Red Faucet
(if SADI-R) (if SADI-D) (if SADI Cla ic)
If any items are missing or any com onents are damaged, contact and notify your dealer.
Push-to-Connect (PTC) Fittings Primer
The manufacturer makes extensive use of PTC fittings in the construction of this device. These fittings will last
many leak-free years when ro erly cut tubing is
ro erly inserted into them. Never cut tubing with a
scissors as this crushes and deforms the new tubing
ends. Instead, slice the tubing with a razor edge such as
a box cutter or a tubing cutter s ecifically designed for
this task. Please review the inset at right before
continuing.
Pre-installation Site Ins ection
Ensure that the Mineral Mizer and storage tank will fit
into the desired location. If inside a cabinet, the Tank is
usually laced at the back and the Mineral Mizer is
ositioned on the right side of the cabinet, roviding
maximum viewing ex osure to the right & center clear
filter sum s. If this is a Mineral Mizer II, make sure that
it is laced within the 15 foot range of the dis ensing
gun assembly. Hand-tighten the filter sum s onto the
Mineral Mizer head before lacing it into the cabinet
for s atial lanning ur oses. The filter housings must
be removed for eriodic service so kee accessibility in
mind.
Pay Attention to All Warnings
Read and adhere to all warnings contained within this manual.
Quick Connect Fittings
All connections are quick connect fittings except for the
compression fitting at the inlet saddle valve, drain saddle
valve and storage tank shutoff valve.
To Prepare Tubing
• Cut the tube squarely and remove any burrs.
• Mark from the end of the tube the length of insertion. (1/4"
O.D. - 11/16", 3/8" O.D. - 3/4")
To Insert Tubing into Fitting
• Insert tube straight into fitting until it bottoms out on interior
shoulder and insertion mark is no longer visible.
To Release Tubing
• Push collet toward body and pull on tubing to release tube.
To re-use fitting, begin assembly over again.

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 6 of 16
Installation Guide
Locate the Mineral Mizer
1. Mount the back anel of the Mineral Mizer head on a wall that will rovide access to change the
filters. If cabinet mounting, mount the Mineral Mizer so that the right side is closest to the front.
Locate the mounting screws using the system-mounting TEMPLATE rovided or sim ly mark and
drill three mounting holes 6.5” a art along a horizontal line at least 18” above the floor. A-dec
MSMD cabinets roduced after A ril 22, 2011 have Mineral Mizer mounting hardware re-
installed at the factory.
2. If the Mineral Mizer will be moved to make routine service easier, move it to that location now.
For exam le, if it is to be mounted inside a cabinet, the service location may be on the floor
directly in front of that cabinet.
3. Place the water Tank within 10 feet of the
Mineral Mizer. For a cabinet install, lace
the Tank in the back of the cabinet with its
valve facing the wall where the Mineral
Mizer will be mounted.
Install lumbing modifications
4. Turn OFF the cold water su ly.
5. Angle Stop Valve - Remove the Angle Sto
Valve from the installation kit. Beneath the
sink, disconnect the faucet’s cold water tube
from its associated stub lumbing. Install
the Angle Sto Valve on the cold water stub lumbing. Reconnect the faucet’s cold water tube to
the to of the Angle Sto Valve. Close the Angle Sto Valve and turn on the cold water su ly,
checking for leaks.
6. In tall the chrome and red faucet - I nstall the chrome & red faucets per its included instructions. Location
options include the sink pop-out or through the countertop overhanging the sink.
IMPORTANT WARNING
-
PLEASE READ
Sy tem Flu hing: The reverse osmosis (RO) membrane and the ost- olishing filter in this system both contain
materials to revent microbiological growth and freezing. If ingested, these may cause irritation of the
gastrointestinal tract, colic, diarrhea or other sym toms and is also unfit for use as autoclave water. The first 5
gallons of water roduced by a RO membrane and the ost- olishing filter must be discarded (flushing of both
com onents occurs simultaneously). Follow the instructions in this manual to ensure this flushing takes lace.
Feed Water Quality: This RO system should not be used for treatment of water that is microbiologically unsafe or
of unknown quality. Unsafe water can cause roliferation of bacteria within the Mineral Mizer, which can lead to
the water being unsafe to handle. If the feed water quality is unknown, have a sam le of the water tested by a
qualified laboratory or agency and im lement the necessary measures to ensure a safe water su ly.
Drain Saddle (installed)
NOTE: Some state or local codes may require that the
drain saddle be served by a trap other than the one
serving the garbage disposal. Before installing, please
check with code authorities.

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 7 of 16
7. Drain Saddle – The Drain Saddle installs on a standard 1½” O.D. vertical section of drain i e.
Install it above the tra and away from the garbage dis osal outlet, if any. Position it to allow
adequate s ace for drilling through the i e, angling the fitting in the direction of the Mineral
Mizer installation. Tighten the Drain Saddle evenly and firmly so a good seal is made. Avoid over
tightening. Drill a 5/16” hole in the drain i e through the drain fitting o ening while su orting
the drain against drilling ressure.
Connect the Mineral Mizer to lumbing
8. Filter Sump - Remove the lastic shrink wra from all filters. Place the filter with the yellow dot
in the left Filter Sum and install it on the filter ca marked with a yellow dot on the bracket.
Place the filters with the red dots in the center and right Filter Sum s, again marked by
corres onding dots on the bracket. Hand-tighten all the Filter Sum s so they are snug. Do not use
the rovided filter wrench to tighten the filter Sum s unless absolutely necessary. Place the
Mineral Mizer in its service location.
9. Drain Tube (black) - After cutting to the a ro riate length,
connect the Drain Tube between the Mineral Mizer’s check
valve marked To Drain and the Drain Saddle fitting.
10. Feed Water Tube (red) –
After cutting to the
a ro riate length, insert the
elbow end of the Feed Water
Tube into the fitting marked
To eed Water and the other
end into the Angle Sto Valve
fitting reviously installed on
the sink lumbing.
11. Tank Tube (blue) – Connect the Tank Tube to the 3/8” elbow on
the Storage Tank Connector at back left, while the other end
hooks u to the elbow ball valve on the storage tank. Kee tank
valve CLOSED for the moment.
12. D.I. Di pen ing Connector (blue)
* FOR DWS-SADI (DISPENSING CONNECTOR TO RED FAUCET): Insert one end
of 3/8” BLUE Tube length into D.I. Dis ensing Connector and the other
end into the bottom of the Red Faucet. Install the Red Faucet er its
included instructions. Location o tions include the sink o -out or
through the counterto overhanging the sink.
Tank Tube
Drain Tube
Feed Water Tube

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 8 of 16
* FOR DWS-SADI-D (DISPENSING CONNECTOR TO DISPENSING GUN): Insert
The elbow end of the Dis ensing Assembly into the fitting marked
Dispenser.
*FOR DWS-SADI-R (DISPENSING CONNECTOR TO REMOTE DISPENSING GUN):
Insert one end of 3/8” BLUE Tube length into D.I. Dis ensing Connector
and the other end into fitting on remote dis ensing gun bracket (See the
DWS-DIDG User’s Manual).
13. Po t-Poli hing Filter Tube (blue) –Connect a 3/8” BLUE tube to the
o en ort on the right side of the Post-Polishing Filter, and then
connect the other end to an already-installed chrome faucet.
Pressure Test Unit For Leaks
14. Turn on the water su ly by o ening the Inline
Valve on the Feed Water Tube, while making sure
that the tank valve and both faucets are all
CLOSED. This will create enough water ressure
in the system to see if there are any ossible
leaks coming from system. Tighten the Filter
Sum s with the Sum Wrench if necessary. Check
the tank for leaks at valve as well.
Production Startu
15. O en the RO Tank valve.
16. Turn ON the water su ly by o ening the Inline
Valve on the Feed Water Tube.
17. O en Chrome Faucet.
18. Allow the Mineral Mizer to roduce water for 4
hours. (You will see black carbon fines for awhile
during the initial flushing of the final filter during startu . This is normal and will cease).
19. Close Chrome Faucet, o en Tank Valve and allow the tank to fill (should take a rox. 3 hours).
20. Once the tank is filled, o en Red Faucet (SADI Classic) or the Dis ensing Gun (SADI-D & SADI-R)
until all air is urged and the water flows smoothly. Close the Red Faucet, make sure that the
tank valve is o en and allow tank to com letely fill until the DWS-SADI sto s making water (tank
is full when the black permeate pump on mounting bracket stops making noise).
Post-Polishing Filter To Chrome Faucet
Dis ensing Connector

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 9 of 16
Rejection rate test
You can test the efficiency (mineral rejection rate) of the RO
membrane as follows:
•Turn off the Feed Water Valve.
•Turn off the Tank valve.
•Release system pressure by opening the faucet valve over
the sink.
•Turn on the Feed Water Valve.
•Slide the switch to the FEED position and hold the faucet
open until the reading stabilizes. This is the feed water TDS.
•Slide the switch to the RO position and hold the faucet open
until the reading stabilizes. This is the RO water TDS.
•Compute the mineral rejection rate = 1 – (RO water TDS /
feed water TDS).
•Recording the mineral rejection rate over time shows the
“health” of the RO membrane. This directly affects the
amount of 000 TDS water produced by a set of DI filters.
21. The Mineral Mizer is now ready for use. To check the
mineral content, slide the Water Quality Monitor’s
switch to the FEED osition. Turn the monitor on by
ressing its ON/OFF switch. The dis lay shows the
water’s mineral content, ex ressed in m TDS. This
number will normally be in the 000 - 002 range. If the
number is higher than 004, allow the tank to fill until
the dis lay is consistently in the 000 – 002 range and
then discard the water as before. This should take no
more than a few minutes. It will take about 3 hours to
fill the Tank, de ending on local water ressure and
tem erature.
22. Call O-SO PURE at 800-676-7873 to register this equi ment. Please rovide the following
information:
•serial #,
•practice name,
•doctor name,
•practice address,
•practice responsible party with phone & email info.
Water Quality Monitor lide witch etting
FEED - Dis lays the mineral content of the feed
(ta ) water.
RO – Dis lays the mineral content of RO water.
DI – Dis lays the mineral content of the DI
water coming out of the red faucet or
dis ensing gun, destined for your boiled water
a lications.

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 10 of 16
O erating Theory
The Mineral Mizer utilizes several modern water technologies to cost-effectively urify your ta water su ly
into buffered low-mineral water for dental unit bottles, or mineral-free, autoclave-grade water.
•Pre-Filter - The yellow dot re-filter contains a combination sediment & carbon block filter. Its function is
to remove sus ended articles, chlorine and chemicals from the feed water, reducing the incidence of
reverse osmosis (RO) membrane clogging and chemical degradation. The re-filter element must be
re laced every twelve months or earlier de ending on the quality of the feed water.
•Rever e O mo i (RO) Module - The RO module contains a semi- ermeable membrane. Its function is to
divide the RO feed water into se arate ermeate (low mineral) and brine (high mineral) streams. This is
accom lished by a lying hydraulic ressure greater than the osmotic ressure in water containing
dissolved solids, effectively allowing water molecules to ass through the membrane while rejecting most
other molecules. The roductivity of the RO membrane is measured in 2 ways:
•water efficiency – the ercentage of RO feed water that is converted to ermeate water.
•rejection rate – the ercentage of minerals rejected from the RO feed water.
Both of these measures are directly affected by the RO feed water ressure and tem erature. The life of the
membrane is determined by measuring the decline in the membrane’s rejection rate over time. Sans this level
of measurement, the membrane should be re laced every 24 to 36 months. (This could be earlier de ending
u on quality of feed water).
DI Filter - The red dot DI filters contain two ty es of beads coated with ion exchange resin. One ty e absorbs
molecular calcium and magnesium while the other absorbs chlorides. In exchange, the resins release hydrogen
and hydroxide ions which combine to create additional water molecules. DI filters have a s ecific ca acity to
absorb minerals so the volume of DI water roduced by a 2 filter set varies based on the mineral content of
the feed water and the rejection rate of the RO membrane. The DI filters must be re laced when exhausted
(TDS m > 5), and at least once annually.
Servicing your Mineral Mizer
Schedule
This schedule is designed for the average otable water su ly and should be followed to ensure the ro er
functioning of your Mineral Mizer.
PART # SERVICE INTERVAL
PRE
-
FILTER DI FILTER RO MEMBRANE
POST
-
FILTER
DWS-RPKSD*
Annual
1 2 1
DWS-LDPF
Only if re-filter clogs between
annual service events
1
DWS-LRDC2
Only if TDS rises above 5 m
between annual service events
2
DWS-ROM-75HE
3 years (2 years if TDS IN > 150
m)
1
These filters may be ordered by contacting the dealer through whom you urchased your Mineral Mizer. Feel
free to contact O-SO Pure at 800-OSO-PURE (800-676-7873) for assistance in ordering from your dealer or by
emailing your name, ractice hone # and desired art # to order@oso ure.com.

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 11 of 16
Filter Stocking Strategies
•Although each Mineral Mizer arrives with a com lete filter set, all ractices will benefit by ordering an
annual service kit (DWS-RPKSD*) once installation is com lete. This ensures the immediate availability
of each filter ty e until the ractice’s unique filter re lacement interval(s) emerge.
•Mineral Mizers rocessing soft feed water (TDS < 150 m) may require only the DWS-RPKSD*
annually, de ending on volume of DI water roduced. In this case, all the filters should be changed.
•Mineral Mizers su lied with hard feed water (TDS > 150 m) may require the DWS-RPKSD* annually
and 1 or more DWS-LRDC2s between annual service intervals. In this case, the ractice may elect to
change only the re-filter at the annual service interval and the DI filters when they are exhausted (TDS
> 5 m). If the weekly volume of DI water roduced is consistent, a DI filter service interval unique to
the ractice will emerge.
•Feed water with high sediment content will cause clogging of the re-filter. As the re-filter clogs,
roduction of DI water diminishes only slightly until the end of the re-filter’s roductivity, making it
a ear that the Mineral Mizer sto s working abru tly. This ractice should kee 1 or more re-filters
in stock and may wish to change the re-filter roactively once a clogging attern emerges.
•Be aware of changes to your DI water usage attern / volume that may consume more DI water than
originally antici ated, resulting in more frequent changes of the DI filters. Some ossibilities include
consum tion by staff, taking water for home use or new boiled water a lications.
Changing Filters
1. Turn off the water su ly by closing the Inline Valve on the Feed Water Tube.
2. If this filter change is the result of a high TDS water reading (TDS m >5), discard the Tank water by
o ening the Chrome Faucet over the sink until water flow sto s. Release the valve.
3. Close the Tank valve.
4. Re lace only one Filter at a time. Note the color dot for the Filter Sum u on which you are working.
Using the Sum Wrench, remove the Filter Sum and discard its filter and water. Remove the lastic
shrink wra from the Filter and lace it in the Filter Sum . Reinstall the Sum on the filter ca . Hand-
tighten the Filter Sum so it is snug. Re eat this ste until all
filters for this service interval are re laced.
5. Turn on the water su ly by o ening the Inline Valve on the
Feed Water Tube (inline to tube direction) and ins ect the
Mineral Mizer and tank for leaks. Tighten the Filter Sum s
with the Sum Wrench if necessary.
6. O en the Tank valve (inline to tubing direction).
7. The Mineral Mizer is now roducing water. To check the
mineral content, slide the Water Quality Monitor’s switch to
the DI osition. Turn the monitor on by ushing its ON/OFF
switch. The dis lay shows the water’s mineral content,
ex ressed in m TDS. This number will normally be in the
000 - 002 range. If the number is higher than 004, allow the
tank to fill until the dis lay is consistently in the 000 – 002
range and then discard the water as before. This should take
no more than a few minutes.
Water Quality Monitor lide witch etting
FEED - Dis lays the mineral content of the feed
(ta ) water.
RO – Dis lays the mineral content of RO water.
DI – Dis lays the mineral content of the DI
water coming out of the red faucet or
dis ensing gun, destined for your boiled water
a lications.

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 12 of 16
8. It will take about 3 hours to fill the Tank, de ending on local water ressure and tem erature. You will
see black carbon fines for awhile during the initial flushing of the final filter after a filter change. This is
normal.
Sanitizing the Mineral Mizer
Because the DI water roduced by the Mineral Mizer is intended to be boiled, the bacterial content of this
water isn’t normally a concern. If, however, there is evidence that bacterial contamination is becoming a
roblem with your Mineral Mizer, following this rocedure to erform a com lete sanitization cycle.
Materials required
•Mild soa solution - Soa used should be as basic as ossible and not contain any fragrances or additives.
•Soft brush - Don’t use scouring ads or instruments that can scratch surfaces.
•Measuring s oon or device.
•Household bleach – unscented, ty ically containing 5.25% sodium hy erchlorate.
•One (1) Gallon of otable water - to mix u a disinfectant solution.
•Dri an or catch basin - to collect any solution or water s illed.
•Pa er towels - to cleanu any s ills.
•Silicone Based Lubricant or KY Jelly- to a ly to O-Rings. Don’t use etroleum-based lubricants.
Other requirements
•Before beginning installation and/or sanitization rocedure, make sure that all tools used are disinfected.
•Thoroughly wash hands with soa before beginning installation and/or sanitization rocedure. If your
hands come into contact with any unsanitary surface while erforming this rocedure or the installation,
hands should be rewashed with soa .
•Any surfaces used to work with to set various com onents on to dry, should be cleaned and disinfected.
•Re lacement filters, membranes and cleaned com onents should be handled as little as ossible.
•A new air of latex or surgical ty e gloves may be used to erform any sanitization rocedure. If the gloves
come into contact with any unsanitary surface while erforming this rocedure, the gloves should be
disinfected or re laced.
Sanitization Procedure
1. Turn off the Inline Valve on the Feed Water Tube.
2. Discard the Tank water by o ening the valve of the Chrome Faucet over the sink until water flow sto s.
Release the valve.
3. Place the Mineral Mizer into the dri an or basin to catch water remaining in the housings as you remove
the Filters and RO membrane.
4. Disconnect the feed tube from the RO membrane module. Unscrew the end ca and remove the
membrane. Discard the RO membrane if re lacing or lace it on a disinfected surface.
5. Remove the Filter Sum s with the Sum Wrench and remove the Filters.
6. Using a cloth or soft brush, clean the Filter Sum s and RO membrane housing with soa and clean water.
7. Lubricate the Filter Sum and RO membrane ca O-rings with silicone lubricant.
8. Reinstall the red dot Filter Sum s (no filters).
9. Reinstall the RO membrane ca and reconnect its feed water tubing.
10. Mix a disinfectant solution of 1 teas oon of 5.25% bleach in 1 gallon of water.

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 13 of 16
11. Pour the disinfectant solution into the yellow dot re-filter sum and reinstall it.
12. O en the Inline Valve on the Feed Water Tube. O en the Chrome Faucet at the sink until water streams
from the faucet. Release the faucet valve, allow the Tank to fill for 10 minutes and close the Inline Valve on
the Feed Water Tube.
13. Let the disinfectant solution sit in the system for 20 minutes.
14. Discard the disinfectant solution by o ening the Chrome Faucet over the sink until water flow sto s.
Release the valve.
15. Install the filters into the Filter Sum s using the instructions for filter re lacement on age 11.
Trouble Shooting Guide
PROBLEM
Probable Cau e Solution
NO WATER OR NOT ENOUGH WATER
Feed water shut off Turn on feed water
Storage tank valve shut off O en tank valve
Plugged or crim ed lines Remove blockage or crim in lines
Pre-filter cartridge clogged Re lace re-filter cartridge
Low feed water ressure Feed water ressure at membrane must be 40+ si
LOW FLOW RATE FROM FAUCET / DISPENSER
Storage tank valve artially closed O en tank valve com letely
Low air ressure in storage tank Increase air ressure to 7 si in storage tank with roduct
water drained
Water leaking from storage tank air valve Storage tank bladder erforated. Re lace storage tank.
HIGH PRODUCT WATER TDS
DI filters exhausted Re lace DI filters
DI FILTER CHANGE INTERVAL DECREASING
Staff using more mineral-free water New mineral-free water a lication
Staff drinking water
RO membrane life ex ired Re lace membrane
Increase in feed water su ly TDS This sometimes ha ens es ecially when the munici al water
utility seasonally uses more well water to satisfy demand.
WATER SMELLS “FISHY”
DI filters exhausted Re lace DI filters

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 14 of 16
Warranty
O
-
SO PURE 1
-
YEAR LIMITED WARRANTY
For new products: DWS- 8, DWS-DDI, DWS-POE, DWS-SADI, DWS-HERO
O-SO PURE warrants this product to be free from defects in workmanship and material under normal usage and service as follows:
All components are warranted for a period of one (1) year from date of installation or thirteen (13) months from date of shipment,
whichever is sooner, with the following exceptions:
•Filters
•UV lamp
This Warranty excludes damages that, in the opinion of O-SO PURE, resulted from:
•shipping, improper installation or unauthorized alteration,
•misuse or negligence,
•exposure to the elements, including but not limited to: direct sunlight, excessive heat, freezing temperatures, humidity or
rainfall,
•accident or excessive wear,
•use with any products not intended for its use,
•acts of God, labor disputes, transportation strikes, or any conditions beyond O-SO PURE’s control.
Repairs must be performed by an O-SO PURE authorized agent with parts obtained from O-SO PURE.
O-SO PURE reserves the right to make revisions to the design or manufacture of this product model without obligation to owner of
this product.
If a defect in material or workmanship is discovered within the warranty period, O-SO PURE’s sole obligation will be to repair or
replace, at its election, the product FREE OF CHARGE upon receipt of the product at O-SO PURE’s repair facility with proof of date of
purchase. Return shipping will be billed to owner. Contact O-SO PURE at 8 -OSO-PURE to arrange shipment.
**IMPORTANT: To ensure proper treatment of source water, purchaser must replace all filters and the UV lamp (if applicable) as
directed in this manual. Failure to service this product as directed voids this Warranty. Filters and UV lamps (if applicable) must be
purchased from O-SO PURE for ANY and ALL CLAIMS TO BE BACKED BY O-SO PURE.
DATE OF PURCHASE: ________________________________________________________________
DISCLAIMER OF WARRANTY: The foregoing warranty (“Warranty”) is in lieu of all other warranties, express or implied, including but
not limited to, any implied warranty of merchantability or fitness for a particular purpose.
Limitation of Remedies: Buyer’s sole and exclusive remedy against O-SO PURE, its employees, agents or representatives
shall be for the repair or replacement of the device as provided for in the Warranty accompanying this Disclaimer. O-SO
PURE, its employees, agents and representatives shall not be liable for consequential damages or any other loss that the
purchaser or any other person or entity suffers or incurs by use of the product subsequent to purchase of the product from
O-SO PURE. This Disclaimer shall apply, without limitation, to any claims made by the original purchaser or any third-party
claim.
No Other Warranties: O-SO PURE gives no warranties, express or implied, other than those contained in the Warranty
accompanying the product. This writing and the Warranty constitute the final, complete and exclusive statement regarding
the terms of the Warranty. Any statements made by any salespersons or agents of O-SO PURE shall NOT be relied on by the
buyer or any other party, and are NOT part of the Warranty. No employee, agent or representative of O-SO PURE or any
other party is authorized to make any warranty in addition to the Warranty, either written or implied.

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 15 of 16
*this page intentionally left blank*

Mineral Mizer Owner’s Manual (rev. 7)
DWS-SADI
Question or comments? Contact O-SO Pure at (800) OSO-PURE or [email protected].
Copyright © 2016 O-SO Pure. All rights reserved.
Page 16 of 16
Certificate of Referral
Please let your rofessional network know how this system assists in your ractice. Give them a co y of this age and they will
receive a $50 rebate on the urchase of an eligible O-SO Pure system. We’ll send you a $25 referral fee when they urchase using
this certificate.
Thi certificate entitle the holder to a $50 rebate on the purcha e of an O-SO Pure water y tem.
Purcha er Info Referring Party Info
Name ________________________________________ Name: ____________________________________
Practice Name: _________________________________ Practice Name: _____________________________
Address: ______________________________________ Address: __________________________________
City/State/Zi : _________________________________ City/State/Zi : _____________________________
Email: ________________________________________ Email: ____________________________________
Phone: ________________________________________ Phone: ___________________________________
Redem tion Instructions & Restrictions
•Purcha er
oFill out the Purchaser information above. This also registers you for making future referrals. We will contact you for
your SSN/TIN.
oPresent this certificate to your dealer at time of order. Rebate will not be a lied retroactively.
oOnly one (1) certificate may be redeemed er eligible O-So Pure water system.
•Dealer
oDealer and dealer em loyees are not eligible for referral fee.
oWhen submitting your urchase order to O-SO Pure
include an image of this certificate, clearly showing the urchaser information
rebate will be sent by O-So Pure directly to the urchaser identified above.
oCertificate must be accom anied by a urchase order..
•Referring party
oOne (1) referral fee will be aid er eligible O-SO Pure water system.
oReferring arty must own O-SO Pure equi ment.
oTo register,
FAX this sheet with Referring Party Information filled out.
email address is required for communication.
O-SO Pure will email IRS form W-9 to be com leted and submitted.
1099 will be issued according to IRS rules in effect.
oO-SO Pure reserves the right to determine form of disbursement (e.g. check, cash, gift card).
oDisbursements will be distributed quarterly, after recei t of ayment from the dealer.
oShould the urchaser return the water system for a refund, O-SO Pure reserves the right to deduct the referral fee
from future disbursements.
Disclaimer
O-SO Pure reserves the right to modify or discontinue this rogram u on notification to registered referring arties. Such
notification will occur via referring arty’s email address. Referring arty shall kee O-SO Pure informed of registration
information changes at su ort@oso ure.com. Be sure to include the unique serial # on this age. Referring arty is
res onsible for monitoring email address on file including SPAM filter settings.