Obihai OBi100 User manual

Off The port is not enabled.
Solid Green The phone is ready to be used.
Flashing Green The phone is in use.
Off The OBi is not receiving power.
Solid Green The OBi is operational.
Flashing Green The OBi is looking for a DHCP IP address.
Flashing Orange The OBi is upgrading. Do not unplug power!
Solid Red The OBi is non-operational.
Flashing Green Light flashes when there is data activity
(Intermittent) on the OBi Ethernet port.(Intermittent) on the OBi Ethernet port.
12-Volt
Power
INTERNET
PHONE
OBi100 Rear
Power Outlet Internet Router Phone
OBi100 Connection
A. Connect an analog phone to the OBi PHONE port. Use the cable currently connected to phone.
B. Connect one end of the Ethernet cable to the OBi INTERNET port and the other end to an
Ethernet port on your Internet router or Ethernet switch.
C. Connect the 12-Volt power adapter to the OBi power jack and a power outlet.
Please observe the following steps to install the OBi.
OBi100 Installation
OBi100 Device Ethernet Cable 12-Volt Power Adapter
Please check to see that you have the following:
1. OBi100 Device
2. Ethernet Cable
3. 12-Volt Power Adapter
You will also need:
1. An active Internet connection.
2. One analog touch tone phone.2. One analog touch tone phone.
3. Access to the Internet via an Ethernet port on your home or office router.
4. (Optional but useful) An Internet phone service subscription with all
required username / password / etc. credentials or provisioned remotely
by a service provider.
Installation Requirements
Copyright © 2010 Obihai Technology, Inc. All rights reserved.
Thank you for choosing Obihai Technology www.obihai.com
OBiTalk Network - Do Not Use For Emergency Service Calls
Obihai Technology does not warrant the availability or quality of the OBiTalk network.
Furthermore, Obihai Technology will not be liable to you or any third party for any costs
or damages arising directly and or indirectly from the use of this product’s hardware &
software including without limits any damage, or for any loss whatsoever.
Replacement, Repair, Refund
After the acceptance of a Return Material Authorization (RMA) request, Obihai will
attempt to refund, repair or replace the product. To request an RMA, please contact
the party from whom you purchased the product.
90-Day Limited Hardware Warranty
Obihai Technology provides a 90-day limited hardware warranty. Obihai warrants
to customer that this product will conform to its published specifications and will be
free from defects in material and workmanship at the time of delivery and for a period
of 90-days thereafter. Without limiting the foregoing, this warranty does not cover any
defect resulting from (a) any design or specification supplied by an entity other than
Obihai, (b) non-observance of technical operating parameters (e.g. exceeding limitingObihai, (b) non-observance of technical operating parameters (e.g. exceeding limiting
values) or (c) misuse, abuse, using in abnormal conditions or alterations of any kind.
Warranty Information
www.obihai.com
With Regulatory, Compliance & Safety Information
Installation & Configuration Guide
Quick Start Guide

iPhone & iPod touch are trademarks of Apple Computer, Inc.
Android is a trademark of Google, Inc.
X-Lite is a trademark of Counterpath Corporation
OBi, OBiTALK are trademarks of Obihai Technology, Inc.
* * *
OBi Device Manager Web Page Access:
1. From a phone attached to the OBi, dial to access
the OBi config attendant.
2. Choose “1” to hear the IP address of the OBi.
3. Enter the OBi IP address in a local PC browser web
site address window:
4. When prompted, enter “4. When prompted, enter “admin” for username &
“admin” for password.
How to Perform a Factory Reset:
1. Power on the OBi device.
2. Locate the Factory Reset button access hole on the bottom of
the OBi. It is a circular hole (a little larger than the others) just
above and to the left of the Model ID on the product label.
3. Using a paper clip or similar instrument, depress the button
inside the hole for 15 seconds. inside the hole for 15 seconds.
4. The Power LED will flash red. This indicates you may release
the button and the OBi will now be reset to its factory defaults.
Note: A service provider may restrict some settings from being reset to a factory default.
This equipment has been tested & found to comply with a Class B digital device in accordance with the specifications of the FCC rules.
This product bares the CE marking indicating compliance with the 89/336/EEC directive.
Important: Only an analog telephone or fax machine should be connected to the OBi PHONE port. Do not connect a cable from
the PHONE port to a telephone jack powered by the phone company. Doing so may cause damage to the OBi electronics.
For indoor use only. Read installation instructions before connecting to a power source. The electric plug & socket must be acces-
sible at all times as this is the main method to disconnect power from the device. Shock Hazard: Do not operate near water or similar
fluid. Do not work with this device during periods of lightning activity. Do not touch wires at end of the phone cables or inside sockets.
Do Not Use OBiTALK for Emergency Calls or Contacting Emergency Services
This equipment is not intended to be used to call emergency services like 911, 112, 999, 000.
Compliance & Safety Information
Go to www.obitalk.com, Register, then Log in to optimize your OBi set-up.
Configure Services & Add Friends
VoIP Service(s), Speed Dial Nos.,
Circles of Trust and Trusted Caller IDs
www.obitalk.com
OBi100
Requires installation and configuration
of a soft phone like Counterpath X-Lite
OBiAPP for PC
Download Obihai
Soft Phones
OBiON for iPhone & Android
The
I
nternet
Sign Up & Log in to the OBiTALK Web Site
To bridge a call from one OBi endpoint to another, call the number associated with the
OBi, allow the Attendant to answer, then follow instructions to complete the call.
To Use an Internet phone service number to call the OBi. Then allow the Attendant to
answer and follow instructions to enter destination number to call.
To use a VoIP service from an attached phone dial destination number to call.
Requires Internet Phone Service Subscription
Requires Internet Phone Service Subscription
Requires Internet Phone Service Subscription
After you have your OBi set up via the OBiTALK web portal, you can use the OBi
to bridge services like calling from your mobile phone to the OBi and then connecting
to your destination via an Internet phone service or the free OBiTALK network.
Using the OBi to Bridge Other Services
Visit Our Web Site at www.obihai.com
At the Support Section of the Web Site You Will Find:
Downloads & Documentation - OBi Software & Documentation
Support Forum - Got a Question Or Comment? Post It at the Forum
Frequently Asked Questions - Knowledge Is Power
Tutorials, Tips & Wizards - Learn About & Get the Most from Your OBi
How to Learn More & Get Support
222 222 222
OBiTALK Test No:
* *
Dial 9 followed by:
At any time, you can make a test call to the OBi Number below:
Mary
John
To call Mary, John dials:
9 followed by
123 456 789
**
**
This OBi is ready to make FREE calls to other OBi endpoints using the OBiTALK network.
On the bottom of your unit, you will see a 9-digit OBi Number. This is your OBi Number.
Give this number to your friends, family and colleagues so they can call you from their OBi
device or using an OBi software application for PCs or mobile phones.
To use the OBiTALK network, all you have to do is install your OBi, pick up the phone and
then call your friends by dialing 9 and their nine-digit OBi Number.
Using OBiTALK to Call Other OBi Endpoints