ADTRAN Express 3100 User manual

Express 3100
Part Number 1200240L2
Document Number 61200240L2-20A
July 1999
1200240L2 Express 3100
336012VUR01 Express 3100 Power Supply, 12 VDC Output

Trademarks
Express 3100 and Express Configuration Software are trademarks of ADT-
RAN, Inc.
Hayes is a registered trademark of Hayes Microcomputer Products, Inc.
HyperTerminal is a registered trademark of Hilgraeve, Inc.
MicroPhone Pro is a trademark of Software Ventures Corporation.
Windows is a registered trademark and Windows NT is a trademark of Mi-
crosoft Corporation.
The Express 3100 incorporates Asynchronous Data Compression based on ei-
ther IBM or hi/fn proprietary intellectual property depending on the time of
manufacture. The following trademarks and copyrights are applicable:
Stacker LZS Compression
Copyright © 1989 Carnegie Mellon University
All rights reserved.
Redistribution and use in source and binary forms are permitted provided
that the above copyright notice and this paragraph are duplicated in all such
forms and that any documentation, advertising materials, and other materials
related to such distribution and use acknowledge that the software was devel-
oped by Carnegie Mellon University. The name of the University may not be
used to endorse or promote products derived from this software without spe-
cific prior written permission. This software is provided “as is” and without
any express or implied warranties, including, without limitation, the implied
warranties of merchantability and fitness for a particular purpose.
hi/fn
5993 Avenida Encinas
Carlsbad, CA
Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: [phone]
© 1999 ADTRAN, Inc.
All rights reserved.
Printed in USA.

iii
ADTRAN Year 2000 (Y2K) Readiness Disclosure
ADTRAN has established a Year 2000 program to ensure that our
products will correctly function in the new millennium. ADTRAN
warrants that all products meet Year 2000 specifications regardless of
model or revision. Information about ADTRAN's Year 2000 compli-
ance program is available at the following:
Important Safety Instructions
When using your telephone equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric shock and
injury to persons. These precautions are listed below.
1. Do not use this product near water (for example, near a bath tub,
washbowl,kitchensink orlaundrytub,inawetbasement,ornear
a swimming pool).
2. Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the
leak.
4. Use only the power cord or power supply indicated in the manu-
al. Check local codes for any special disposal instructions.
SAVE THESE INSTRUCTIONS.
Product Matrix www.adtran.com/y2kfax.html
Lists Y2K plans and product certifications.
E-mail yea[email protected]m
Faxback
Document Line [phone]
See also Product Matrix, above.
Y2K Project
Line [phone]

iv
FCC regulations require that the following information be
provided in this manual:
1. This equipment complies with Part 68 of the FCC rules. On the
bottom of the equipment housing is a label that shows the FCC
registration number and Ringer Equivalence Number (REN) for
this equipment. If requested, provide this information to the tele-
phone company.
2. If this equipment causes harm to the telephone network, the tele-
phone company may temporarily discontinue service. If possible,
advance notification is given; otherwise, notification is given as
soon as possible. The telephone company will advise the custom-
er of the right to file a complaint with the FCC.
3. The telephone company may make changes in its facilities, equip-
ment, operations, or procedures that could affect the proper oper-
ation of this equipment; advance notification and the opportunity
to maintain uninterrupted service is given.
4. If experiencing difficulty with this equipment, please contact
ADTRAN for repair and warranty information. The telephone
company may require this equipment to be disconnected from the
network until the problem is corrected or it is certain the equip-
ment is not malfunctioning.
5. This unit contains no user-serviceable parts.
6. An FCC-compliant telephone cord with a modular plug is provid-
ed with this equipment. This equipment is designed to be connect-
ed to the telephone network or premises wiring using an FCC-
compatible modular jack, which is Part 68 compliant.
7. The following information may be required when applying to the
local telephone company for leased line facilities.
Service
Type Digital Facility Interface Code ServiceOrder Code Network Jacks
ISDN 021S5 6.0F RJ-45

v
Federal Communications Commission Radio Frequency
Interference Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated ina commercial environ-
ment. This equipment generates, uses, and can radiate radio frequen-
cy energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to TV or radio reception,
which can be determined by turning the equipment on and off. The
user is encouraged to try to correct the interference by one or more of
the following methods:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Changes or modifications to this unit not expressly
approved by ADTRAN will void the user’s authority
to operate the equipment.

vi
WARRANTY: ADTRAN warrants that items manufactured by
ADTRAN and supplied under Buyer’s order shall be freefrom defects
in materials and workmanship and will conform to applicable
specifications and drawings. ADTRAN’s liability herein, whether
based upon breach of warranty or contract or negligence in
manufacture, shall be limited to replacement or repair at ADTRAN’s
election of all such defective or nonconforming items, provided that
this warranty shall apply only where Buyer has given ADTRAN
written notice of such defects or nonconformity within five (5) years*
after delivery by ADTRAN of such items to Buyer. ADTRAN shall
have the right prior to return to inspect at Buyer’s plant any items
claimed to be defective or nonconforming.
*Note: The following items carry warranty period as shown.
1. Items not of ADTRAN manufacture will carry the remaining war-
ranty and related terms and conditions of the original manufac-
turer.
2. Encapsulated U-Repeater and Encapsulated DDS Repeater—two
years.
The foregoing constitutes the sole and exclusive remedy of the Buyer
and exclusive liability of ADTRAN AND IS IN LIEU OF ANY AND
ALL OTHER WARRANTIES EXPRESSED OR IMPLIED OR STATU-
TORY AS TO MERCHANTABILITY, FITNESS FOR PURPOSE SOLD,
DESCRIPTION, QUALITY, PRODUCTIVENESS OR ANY OTHER
MATTER. Without limiting the foregoing, in no event shall ADTRAN
be liable for the loss of use or profit or other collateral, special or con-
sequential damages.
RETURNS: Return authorizationmust beobtained from ADTRANpri-
or to return of any items, including those for repair. Buyer’s right to
repair or replacement is governed by this Warranty. Issuance ofcredit
for returned items shall be made at ADTRAN’s discretion upon Buy-
er’s request. All returns for credit acceptedby ADTRAN are subject to
a restocking fee.
SHIPPING: The cost of shipping the equipment from Buyer’s facility
back to ADTRAN shall be paid by the Buyer. The cost for return ship-
ping of the equipment by surface carrier shall be paid by ADTRAN.
ADTRAN will utilize other means of express shipment at the request
of the Buyer. The cost of shipping shall be paid by the Buyer if express

vii
shipment is requested. In-warranty equipment returned for repair
that is found not defective will carry a nominal charge to cover han-
dling cost.
OUT OF WARRANTY: The cost of out-of-warranty repairs including re-
turn shipment are subject to a charge as quoted by ADTRAN. The cost
of the repair will be invoiced and the return of the item will be made
using the most economical shipment means available. ADTRAN will
use other means of express shipment at the request of the Buyer. In
this case, the cost of shipping shall be paid by the Buyer.
ALTERATION TO EQUIPMENT PURCHASED: Modification or alter-
ation to purchased equipment by Buyer, other than that specifically
authorized by this Agreement or by ADTRAN, shall VOID AND
NULLIFY, in its entirety, all warranty conditions as set forth in War-
ranty paragraph.
ENGINEERING CHANGES: ADTRAN reserves the right to make
progress and design changes in standard product items ordered with-
out prior approval or notification to Buyer and without incurring any
obligations or liability to make the same changes in items previously
manufactured.
DATA RIGHTS: Rights to any intellectual property residing in the
products or any data furnished hereunder are not granted except by
specific written permission by an authorized representative of
ADTRAN. Buyer shall have no right to copy or reproduce in whole or
part any data furnished hereunder without the prior written consent
of ADTRAN.
PATENT AND COPYRIGHT INDEMNITY: ADTRAN warrants that the
equipment and documentation furnished under this Agreement shall
be free and clear of infringement of any patent or copyright covering
the structure or composition of such articles or documentation. In the
event of a claim, suit, or action against Buyer alleging such
infringement, ADTRAN shall save Buyer and its affiliates, agents or
customers harmless from liability as finally determined by a court of
competent jurisdiction, for such infringement, provided that Buyer
gives ADTRAN notice promptly of such claim, suit, or action, and
shall have given ADTRAN full and exclusive control of the defense
thereof, and that ADTRAN shall have sole right to settle or
compromise such claim, suit, or action.

viii
In the event of a claim, suit or action against ADTRAN alleging
infringement by the use of any such equipment or documentation,
furnished under this Agreement, in combination with other articles or
in carrying out any process covered by a patent owned or controlled
by any other person, in which independent use of the equipment
under this Agreement wouldnot be an infringement. Buyer shall save
ADTRAN harmless from liability, as finally determined by a court of
competent jurisdiction, for such infringement, provided that
ADTRAN shall have given Buyer full and exclusive control of the
defense thereof, and that Buyer shall have the sole right tosettle claim,
suit or action.
Except as herein provided in this indemnity paragraph, neither Buyer
nor ADTRAN makes any warranty to the other with respect to any
claim, suit or action of any third party by way of infringement and nei-
ther party shall be responsible to the other for any loss, cost or damag-
es consequential or otherwise, that may be suffered by the other as a
result of any such claim, suit or action.

ix
Affidavit Requirements for Connection to Digital Services
• An affidavit is required to be given to the telephone company
whenever digital terminal equipment without encoded analog
content and billing protection is used to transmit digital signals
containing encoded analog content which are intended for even-
tual conversion into voiceband analog signals and transmitted on
the network.
• The affidavit shall affirm that either noencoded analog content or
billing information is being transmitted or that the output of the
device meets Part 68 encoded analog content or billing protection
specifications.
• End user/customer will be responsible to file an affidavit with the
local exchange carrier when connecting unprotected Customer
Premises Equipment (CPE) to 1.544 Mbps or subrate digital ser-
vices.
• Untilsuchtime assubratedigital terminalequipmentisregistered
for voice applications, the affidavit requirement for subrate ser-
vices is waived.
Affidavit for Connection of Customer Premises Equipment to
1.544 Mbps and/or Subrate Digital Services
For the work to be performed in the certified territory of
_________________________________ (telco name)
State of __________________________
County of ________________________
I, _______________________________ (name),
_________________________________ (business address),
_________________________________ (telephone number)
being duly sworn, state:
I have responsibility for the operation and maintenance of the termi-
nalequipmenttobeconnectedto1.544 Mbpsand/or________subrate
digital services. The terminal equipment to be connected complies
with Part 68 of the FCC rules except for the encoded analog content
and billing protection specifications. With respect to encoded analog
content and billing protection:

x
( ) I attest that all operations associated with the establishment, main-
tenance, and adjustment of the digital CPE with respect to analog con-
tent and encoded billing protection information continuously
complies with Part 68 of the FCC Rules and Regulations.
( ) The digital CPE does not transmit digital signals containing en-
coded analog content or billing information which is intended to be
decoded within the telecommunications network.
( ) The encoded analog content and billing protection is factory set
and is not under the control of the customer.
I attest that the operator(s)/maintainer(s) of the digital CPE responsi-
bleforthe establishment,maintenance,andadjustmentoftheencoded
analog content and billing information has (have) been trained to per-
form these functions by successfully having completed one of the fol-
lowing (check appropriate blocks):
( ) A. A training course provided by the manufacturer/grantee of the
equipment used to encode analog signals; or
( ) B. A training course provided by the customer or authorized repre-
sentative, using training materials and instructions provided by the man-
ufacturer/grantee of the equipment used to encode analog signals; or
( ) C. An independent training course (e.g., trade school or technical
institution) recognized by the manufacturer/grantee of the equip-
ment used to encode analog signals; or
( ) D. In lieu of the preceding training requirements, the operator(s)/
maintainer(s) is (are) under the control of a supervisor trained in ac-
cordance with _________ (circle one) above.
I agree to provide _________________ (telco's name) with proper doc-
umentation to demonstrate compliance with the information as pro-
vided in the preceding paragraph, if so requested.
_________________________________Signature
_________________________________Title
_________________________________ Date
Transcribed and sworn to before me
This ________ day of ________, ________
_________________________________
Notary Public
My commission expires:
_________________________________