OBSBOT Me User manual

Overview
About Me
OBSBOT Me AI-powered selfie phone mount inherited the strong tracking ability of the OBSBOT family,
uses deep learning neural networks and brushless motor control technology to provide an accurate and
stable tracking experience.
Parts Info
01 09
02
03
04
05
06
07
10
11
08
12
󾙓
01. Phone Holder
02. Phone Holder Arm
03. Vertical Rotation Axis
04. Horizontal Rotation Axis
05. Lens
06. Status Indicator
07. Power Indicator
08. Power Button
09. Universal Joint Tightness Adjustment Knob
10. Universal Joint
11. USB Type-C Interface
12. UNC 1/4-20 Interface
User Manual

Installation and Leveling
Install the phone.
To install the phone, you need to make sure the OBSBOT Me is turned off.
Open the phone holder and put the phone into it, before shooting, you need to adjust the phone to make
it balanced.
Shooting with the selfie camera Shooting with the rear camra
4
Unfold the OBSBOT Me
Quick Start
Hold the Phone holder arm and rotate it vertically clockwise or counterclockwise by 180° to unfold the
OBSBOT Me.
Conversely, it can be folded for storage.
󾙔
1 2 3
Horizontal Rotation
Hold the phone holder arm and rotate it horizontally clockwise or counterclockwise by 180°，suitable for
shooting by the rear camera of your phone.
1 2 3
󾙕

The Power Button Instruction
Lock / Unlock the Tracking Target
OBSBOT Me provides two ways to lock or unlock the tracking target.
Gesture control
To perform gesture control, users can simply show the same pose below in front of the sensing camera.
*Please be careful not to block your face while doing the gesture, and slightly spread your fingers.
To make the OBSBOT Me lock the tracking target, just do the same pose shown in the picture below.
When the OBSBOT Me successfully locks the tracking target, the status indicator light will flash green light
twice, then turn blue and stay on.
󾙖
Adjust the tightness of the universal joint.
The phone holder is connected to the phone holder arm by a universal joint. If the phone holder is
loosened, you can use the metal round plate in the package to tighten it.
Use with a tripod
OBSBOT Me equipped with a 1/4’’ interface, please use it with the tripod that comes along with the
package. OBSBOT Me is also compatible with all mainstream tripods on the market.
How to use the metal plate
Loose
Tight
Adjust the camera angle
You can adjust the universal joint to change the camera angle.
󾙗

a. please make sure that the back of the phone is entirely close to the panel of the phone clip, and the long
side of the phone should be fully buckled into the phone clip.
b. Make sure that the smart phone and phone holder in a balanced state during the usage.
c. The phone holder is specially designed for preventing pressing smartphone buttons by accident.
Button Instruction
In shutdown state, press the button to check the power level.
In shutdown state, press the button and hold for 3s to power on the
product.
In the powered-on state, press the button once to lock/unlock the
tracking target.
In the powered-on state, Press the button and hold for 3s to turn off the
product.
In the powered-on state, after turn on the ‘Gesture Control-Button
Switch’ on the OBSBOT Me Tool, you can triple-click the button on the
device to turn on/off the ‘Gesture Control’ function.

To make the OBSBOT Me unlock the tracking target, it requests the locked person do the pose in front of
the sensing camera.
When the OBSBOT Me successfully unlock the tracking target, the status indicator light will flash blue light
twice, then turn green and stay on.
Tracking Distance
The best tracking distance range is 0.5 meter to 3 meters away from the OBSBOT Me, the furthest tracking
distance is 15 meters.
<3m>0.5m <15m
The status indicator light can display three colors of yellow, green and blue. The combination of different
colors and blink pattern respectively represent different status of product.
The Status Indicator Light
󾙘
0.5m
3m
±60°
󾙙
Quick pick
In the powered-on state, you can lock/unlock the tracking target by pressing the power button.
If the OBSBOT Me doesn’t have a locked target, you can make the OBSBOT Me lock a person by a simply
click on the power button.
When the OBSBOT Me successfully locks a target, the status indicator light will turn blue and stay on; If
there is no available target, the status indicator light will flash blue light, and the OBSBOT Me will enter
target searching mode.
* Target searching mode and recognizable range: When using Quick pick to try locking a person, the best
recognition range is a fan shape area as shown below in the picture.
If you use Quick pick but there are no available targets, the OBSBOT Me will enter target searching mode,
the status indicator light will keep blinking blue.
In the target searching mode, OBSBOT Me will continue to search for a target, when a person enters the
recognition range, the status indicator will turn blue and stay on, indicating that the target searching is
successful; if there are no available targets within the best recognition range for 3 second, the status
indicator will turn green and stay on, indicating that the target search has failed.
To unlock the tracking target, you can simply click the power button.
When the OBSBOT Me successfully unlock the target, the status indicator light will turn to green and stay
on.
Lock/unlock the tracking target
Definition Lighting
Boot initialization
Not target locked
Target locked
Gesture recognition
The status indicator light turns blue and stays on for 5
seconds, then starts to flash blue every second.
The status light flash twice, then turn to the light keeps
on which means identified.
Solid blue.
Solid green.
Target searching mode Blinking blue.

󾙚 󾙛
Power indicator light
StatusPower level
󾙒󾙛
󾙓󾙒󾙖󾙛
󾙗󾙒󾙓󾙒󾙒
󾙒󾙛
󾙓󾙒󾙖󾙛
󾙗󾙒󾙛󾙛
󾙓󾙒󾙒
Category
Power level display
Charging
Flashing
Solid
Charging
To charge OBSBOT Me, you can connect OBSBOT Me with a power adaptor or a power bank by a USB
Type-C cable,
It takes 75 minutes to fully charge the battery, the power indicator light will keep flashing when charging,
and it will turn to solid green after fully charged.
* OBSBOT Me has a 950mAh battery capacity, and a play time of 120 minutes
Battery and Charging
Software Overview
OBSBOT Me tool is the software that comes with the OBSBOT Me. It is compatible with Windows and
macOS. The user can do some control such as turn on/off gesture control or upgrade firmware, and so on.
Installation
Please visit https://obsbot.com/download to download the OBSBOT Me Tool to get further user experience.
OBSBOT Me Tool
Definition Lighting
Target lost Solid yellow.
Upgrading
Fail to upgrade
Gimbal error, AI error etc Blinking green, yellow and blue.
Flash yellow.
Gesture Control-Button
Switch
The status blue light flash twice, which means the
switch is successful.
Blinking green and blue.

The content is subject to update without notice. Please download the latest version of "User Manual" on the
ocial website of REMO TECH:
https://www.obsbot.com
OBSBOT
OBSBOT_Ocial
Homepage Firmware Upgrade
OBSBOT Me can be upgraded in OBSBOT Me Tool. A prompt will be displayed after the device is connected
when the firmware is available to upgrade. Please follow the instructions.
⚠Do not disconnect the OBSBOT Me during firmware upgrade.
Please check the Firmware Upgrade Guide on https://obsbot.com/service/user-guide
1. Software Version
Find the current software version. The update will be pushed to the device automatically when the new
version has been released.
2. Gesture Control
By default, it’s on. The product cannot be used with gesture control for locked the target if you close this
function.
3. Gesture Control-Button Switch
By default, it’s off. After turn on the function, you can tripe-click the button on the device to turn on/off
the ‘Gesture Control’ function.
Tips: After tripe-click the button, you can find the bule lights flash for twice which means executed
successfully.
4. Manual Upgrade
By default, the firmware is automatically upgraded. You can switch to manually upgrading after checking
the box.
5. Current Version
By Find the current firmware version. The update will be pushed to the device automatically when the new
version has been released.
6. Update Now/Choose Firmware
Auto Upgrade：When a new firmware is released, click ‘Update Now’ to start the firmware upgrade
process.
Manual Upgrade：Click ‘Choose Firmware’ to select a firmware package to start the manual upgrade
process.
7. Export Log
Manually export the log file.
Update Now Choose Firmware