OEM Tools 24862 Service manual
UNPACKING
After unpacking unit, inspect carefully for any damage
that may have occurred during transit. Check for loose,
missing, or damaged parts. If any damage is observed,
a shipping damage claim must be filed with carrier. Do
not use OEMTOOLS™ 21 Gallon Oil Drain Vacuum
and Extractor if broken, bent, cracked or damaged
parts (including labels) are noted. Any Waste Oil Drain
- Extractor that appears damaged in any way, operates
abnormally or is missing parts should be removed from
service immediately. If you suspect that the Waste
Oil Drain - Extractor was subjected to a shock load (a
load that was dropped suddenly, unexpectedly, etc.)
immediately discontinue use until it has been checked
by a factory authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect
yourself and others by observing all safety information, warnings, and cautions. Failure to comply with instructions
could result in personal injury and/or damage to product or property. Please retain instructions for future reference.
The following safety information is provided as guidelines to help you operate your Waste Oil Drain-Extractor
under the safest possible conditions. Any tool or piece of equipment can be potentially dangerous to use
when safety or safe handling instructions are not known or not followed. The following safety instructions are
to provide the user with the information necessary for safe use and operation. Please read and retain these
instructions for the continued safe use of your service system. Failure to follow instructions listed below may
result in serious injury. In addition, make certain that anyone that uses the equipment understands and follows
these safety instructions as well.
WARNING:This product can expose you to chemicals, including DEHP and lead, which are known to the State of
California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Operating Instructions and Parts Manual 24862
05/19
2019 OEMTOOLS™
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
21 GALLON OIL DRAIN
VACUUM AND EXTRACTOR
WARNING
Explanation of Safety Signal Words
: Indicates a potentially hazardous
situation which, if not avoided, could result in death or serious injury.
: Indicates a potentially hazardous
situation which, if not avoided, could result in death or serious injury.
CAUTION : Used without the safety alert symbol indicates a potentially hazardous situation
which, if not avoided, may result in property damage.
Notes : Provide clarity and helpful information.
CAUTION
WARNING
2
Operating Instructions and Parts Manual 24862
21 GALLON OIL DRAIN
VACUUM AND EXTRACTOR
Thank you very much for choosing an OEMTOOLS
Product!
For future reference, please complete the owner’s
record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is
important that you read the entire manual to become
familiar with this product before you begin using it.
This machine is designed for certain applications
only. OEMTOOLS cannot be responsible for issues
arising from modification. We strongly recommend
this machine is not modified and/or used for
any application other than that for which it was
designed. If you have any questions relative to a
particular application, DO NOT use the machine until
you have first contacted OEMTOOLS to determine if
it can or should be performed on the product.
For technical questions please call 1-866-458-2472.
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your tool. Read this manual carefully. Learn
the tool’s applications and limitations, as well as,
potential hazards specific to it.
2. Keep work area clean and well lit. Cluttered or dark
work areas invite accidents.
3. Keep children away. All children should be kept
away from the work area. Never let a child handle
a tool without strict adult supervision.
4. Do not operate this tool if under the influence
of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or
reflexes are impaired while taking drugs. If there is
any doubt, do not attempt to operate.
5. Use safety equipment. Eye protection should
be worn at all times when operating this tool.
Use ANSI approved safety glasses. Everyday
eyeglasses are NOT safety glasses. Dust mask,
non-skid safety shoes, hard hat or hearing
protection should be used in appropriate
conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-
ties, rings, bracelets or other jewelry may present a
potential hazard when operating this tool. Keep all
apparel clear of the tool.
7. Don’t overreach. Keep proper footing and balance
at all times when operating this tool.
8. Check for damage. Check your tool regularly. If
part of the tool is damaged it should be carefully
inspected to make sure that it can perform its
intended function correctly. If in doubt, the part
should be repaired. Refer all servicing to a qualified
technician. Consult your dealer for advice.
9. Keep away from flammables. Do not attempt
to operate this tool near flammable materials
or combustibles. Failure to comply may cause
serious injury or death.
10. Store idle tools out of the reach of children and
untrained persons. Tools may be dangerous in the
hands of untrained users.
• Maintain tools with care.
• Keep tools dry and clean.
• Properly maintained tools are less likely to bind and
are easier to control. Do not use a damaged tool. Tag
damaged tools “Do not use” until repaired.
• Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation.
• If damaged, have the tool serviced before using. Many
accidents are caused by poorly maintained tools.
• Use only accessories that are recommended by the
manufacturer for your model. Accessories that may
be suitable for one tool may become hazardous when
used on another tool.
• Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
• When servicing a tool, use only identical replacement
parts. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of injury.
• Maintain a safe working environment. Keep the work
area well lit. Make sure there is adequate surrounding
workspace. Keep the work area free of obstructions,
grease, oil, trash, and other debris. Do not use this
product in a damp or wet location.
• Maintain labels and nameplates on this product.
These carry important information. If unreadable or
missing, contact OEM for a replacement.
• Keep the handle dry, clean, and free from brake fluid,
oil, and grease.
• Before use, read and understand all warnings, safety
precautions, and instructions as outlined in the
vehicle manufacturer’s service manual. It is beyond
the scope of this manual to properly describe the
correct procedure and test data for each vehicle.
05/19
2019 OEMTOOLS™
3
Operating Instructions and Parts Manual 24862
21 GALLON OIL DRAIN
VACUUM AND EXTRACTOR
• Always perform vehicle service in a properly ventilated
area. Never run an engine without proper ventilation
for its exhaust. Stop work and take necessary steps
to improve ventilation in the work area if you develop
momentary eye, nose, or throat irritation as this
indicates inadequate ventilation.
• Engine parts that are in motion and unexpected
movement of a vehicle can injure or kill. When working
near moving engine parts, wear snug fit clothing and
keep hands and fingers away from moving parts.
Keep hoses and tools clear of moving parts. Always
stay clear of moving engine parts. Hoses and tools
can be thrown through the air if not kept clear of
moving engine parts. The unexpected movement of
a vehicle can injure or kill. When working on vehicles
always set the parking brake or block the wheels.
• Be alert for hot engine parts to avoid accidental burns.
• If you drove your car recently, fluids could be very hot.
Allow at least 2 hours before you handle any fluids. Oil
and Coolant burns are very dangerous.
• Avoid accidental fire and/or explosion. Do not smoke
near engine fuel and battery components.
• Never remove the cap from the radiator or expansion
tank while the engine is at operating temperature.
• Always allow the engine to cool before removing
the radiator cap or expansion tank cap. The cooling
system is under pressure. Failure to allow the engine
to cool before attempting to remove the cap could
result in serious injuries.
• Does not misuse, over-pressurize, modify parts, or
use worn and/or damaged parts.
• Do not use oil drain for flammable or caustic fluids.
• Do not exceed 7 psi (0,5 bar) air pressure when
emptying the oil drain.
• The warnings, precautions, and instructions discussed
in this manual cannot cover all possible conditions
and situations that may occur. The operator must
understand that common sense and caution are
factors which cannot be built into this product, but
must be supplied by the operator.
• For safety purposes and the prevention of damage
to expensive components it is advised that the user
have an understanding of basic automotive repair and
a working knowledge of automotive systems.
• We believe the information contained herein to be
reliable. However, general technical information is
given by us without charge and the user shall employ
such information at his own discretion and risk. We
assume no responsibility for results or damages
incurred from the use of such information in whole or in
part. Always refer to specific instructions and technical
information supplied by vehicle manufacturer.
• The manufacturer declines any and all responsibility
for damage to vehicles or components if said damage
is the result of unskillful handling by the operator or of
failure to observe the basic safety rules set forth in the
instruction manual.
• Used oil, antifreeze, brake fluid and transmission fluid
contains chemical compounds that can be harmful to
humans and other animals. When managed properly,
used oil may again be of beneficial use. Used oil may
be blended and recycled as a heating or industrial
fuel and also may be re-refined and made into new
lubricants. Persons who perform maintenance on
their own vehicles are responsible for managing the
used fluids in a manner that is protective of human
health and the environment and to follow all local laws
and regulations concerning their disposal.
DISPOSAL
At the end of the useful life of the Waste Oil Drain -
Extractor, dispose of the components according to all
state, federal, and local regulations
PURPOSE
The 24862 Waste Oil Drain - Extractor is designed
for the collection of used fluids including motor oil,
transmission fluid, and coolant from under lift-mounted
vehicles, or by evacuation directly from fluid reservoirs
or through dipstick tubes. The portable oil drain
system is designed to safely capture oil and other
vehicle fluids with the use of a large funnel or vacuum.
After use, the drain is emptied using air pressure. An
external air supply is required.
05/19
2019 OEMTOOLS™
Reservoir Capacity 80L (21 Gallons)
Discharge Hose Length 82”
Oil Drain Funnel Diameter 15”
Oil Drain Extension Diameter 22”
Funnel Height Adjustment 45”-62”
Caster 3-1/2” 2, Swivel-2,
Swivel with Lock
Max Air Pressure 7 psi
PRODUCT SPECIFICATIONS
4
Operating Instructions and Parts Manual 24862
21 GALLON OIL DRAIN
VACUUM AND EXTRACTOR
Figure Description Quantity
24862-1 Oil Drain Extension 1
24862-2 Oil Drain Funnel 1
24862-3 Pressure Gauge 1
24862-4 Safety Valve (Not Shown) 1
24862-5 Release Valve 1
24862-6 Central Drain Tube 1
24862-7 Air Fitting 1
24862-8 Waste Oil Discharge Hose 1
24862-9 Waste Oil Discharge Valve 1
24862-10 Caster (with brake) 2
24862-11 Caster (no brake) 2
24862-12 Pressure Valve (Not Shown) 1
24862-13 Dipstick/Flex Tub Adpaters 5
24862-14 Cleaing Rod 1
24862-15 Venturi System 1
24862-16 Vacuum Gauge 1
24862-17 Oil Suction Valve (Not Shown) 1
24862-18 Oil Suction Hose 1
NOTE
Not all components of the Waste Oil Drain - Extractor are
replacement items, but are illustrated as a convenient
reference for location and position in the assembly
sequence.
05/19
2019 OEMTOOLS™
(1)
(2)
(3)
(5)
(6)
(7)
(8)
(9)
(10) (11)
(13)
(14)
(15)
(16)
(18)
5
Operating Instructions and Parts Manual 24862
21 GALLON OIL DRAIN
VACUUM AND EXTRACTOR
Always wear safety glasses and gloves!
OPERATING INSTRUCTIONS
• This equipment is intended only for professional use by personnel trained in performing the service functions for
which it is has been designed
• This equipment is designed for servicing a variety of vehicles in a safe, convenient manner. However, differences
in vehicle makes and models may make it impossible to use this equipment as it is intended. Do not attempt to
force the use of this equipment on an application for which it is not designed to perform.
• The procedures documented in this manual are to serve as guidelines for the use of this equipment.
• In addition to these guidelines, always follow the manufacturer’s recommended procedures when servicing each
unique vehicle.
• The use of this equipment is simple and straightforward if you follow the instructions. However, always keep in
mind that you are working with a system that may be under pressure, with fluid that is just waiting to be expelled.
When operating this equipment, use common sense, and always stop to think before disconnecting a hose or
other component.
• Always use the Waste Oil Drain - Extractor on a flat, level surface and lock casters before using.
DO NOT USE THIS EQUIPMENT WITH GASOLINE OR OTHER FLAMMABLE LIQUIDS OR WITH
FLUIDS AT TEMPERATURES ABOVE 175° FAHRENHEIT (80° CELSIUS)
KEEP AWAY FROM OPEN FLAMES OR EXCESSIVE HEAT
COLLECTING WASTE OIL USING THE FUNNEL
1. Position the Waste Oil Drain - Extractor under the vehicle and adjust the bowl to the desired height and set
the brakes on the casters
2. Check the sight glass to ensure there is sufficient remaining capacity. Never allow fluid to exceed the
maximum level. The reservoir will not drain if the fluid exceeds the maximum level on the sight glass.
COLLECTING WASTE OIL USING THE EXTRACTION TUBE
1. Make sure air valve on the side of air regulator is closed.
2. Choose a suitable Extraction Tube from the selection provided with the unit. Insert the Extraction Tube to the
bottom of oil pan. Do not kink the tube.
3. Connect Extraction Tube to the Oil Suction Hose
4. Connect shop air supply to the air connection and check if the pressure is in safety range.
NOTE
The working pressure must be between 75-120psi
5. Open the air valve to create a vacuum and start oil extraction.
NOTE
Verify fluid level gauge does not show tank is full and has enough remaining capacity.
6. For best results, crankcase oil needs to be at least 150°F, not to exceed 175°F.
7. Close air valve once crankcase or reservoir is empty.
05/19
2019 OEMTOOLS™
WARNING
WARNING
6
Operating Instructions and Parts Manual 24862
21 GALLON OIL DRAIN
VACUUM AND EXTRACTOR
DRAINING THE RESEVOIR
1. Set the caster brakes. Close the release valve (5) on the side of the Drain Tube.
NOTE
If valve is not closed, waste oil will shoot out of the funnel and spray the user.
2. Secure the discharge hose to the bulk waste oil tank and open the discharge hose valve.
3. Set the air supply to a maximum of 7 psi (0,5 bar).
Do not exceed 7 psi (0,5 bar). Failure to comply may result in serious personal
injury
4. Connect air supply to valve stem using air chuck tire inflator.
5. Remove air chuck from valve stem when desired flow rate is achieved or if safety relief valve opens.
NOTE
If flow rate stops before drain is empty, repeat steps 3, 4, and 5.
MAINTENANCE
1. Relieve pressure or vacuum before inspecting or servicing
2. Always store the Waste Oil Drain - Extractor in a well-protected area where it will not be exposed to
inclement weather, corrosive vapors, abrasive dust, or any other harmful elements.
3. Keep the Waste Oil Drain - Extractor clean for better and safer performance.
4. Inspect Reservoir, Hoses, Caps, Gaskets, Seals, and Gauge periodically, and if damaged, replace them.
WARNING
WARNING
05/19
2019 OEMTOOLS™
7
Operating Instructions and Parts Manual 24862
21 GALLON OIL DRAIN
VACUUM AND EXTRACTOR
OEMTOOLS™ ONE YEAR LIMITED WARRANTY
Please read the following carefully
OEM and/or its distributors have provided the parts list and assembly diagram as a reference only. Neither OEM
nor its distributors make any representation or warranty of any kind to the buyer and/or user of this tool that he
or she is qualified to do any repairs or replace any parts of this product. OEM and it’s distributors expressly
state that all repairs or parts replacement should be done by certified or licensed technicians. The buyer
assumes all risk and liability arising out of his or her repairs or parts replacement to the original production.
From one year from the original purchase date of this product, OEMTOOLS will warranty this product. If you
find any defect in material or workmanship, through normal usage, return it to the place of purchase or to
OEMTOOLS for repair or replacement at our discretion. In order to obtain this service send your tool and proof
of purchase, transportation pre-paid, to OEMTOOLS Q.A. Dept., 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation, please insure your package. If
our inspection verifies the defect, we will either repair or replace the product at our election, or we may elect
to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes
not within the scope of our warranty, then you must bear the cost of returning the product.
OEMTOOLS does not provide warranty for products labeled other than OEM or OEMTOOLS. OEMTOOLS will
not provide any warranty for products subjected to abnormal use. Abnormal use includes, but is not limited to,
abuse, accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not
cover bits, blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or
replace blades, bits, files, and batteries as necessary. OEMTOOLS reserves the right to makes any changes in
construction or design at any time without any obligation in incorporating such changes to tools or equipment
previously sold.
OEMTOOLS makes every effort to assure that its products meet high quality and durability standards, and
warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of one year from the date of purchase. This warranty does not apply to damage due directly or indirectly
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may
also have other rights, which vary from state to state.
CONTACT US
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: 1-866-458-2472
www.oem-tools.com
05/19
2019 OEMTOOLS™
Table of contents
