OEM Tools 25712 Service manual

UNPACKING
After unpacking unit, inspect carefully for any damage
that may have occurred during transit. Check for loose,
missing, or damaged parts. If any damage is observed,
a shipping damage claim must be filed with carrier.
Do not use the Battery-Operated Liquid Transfer Pump
if broken, bent, cracked or damaged parts (including
labels) are noted. Any Battery-Operated Liquid Transfer
Pump that appears damaged in any way, operates
abnormally or is missing parts should be removed from
service immediately. If you suspect that the Battery-
Operated Liquid Transfer Pump was subjected to a shock
load (a load that was dropped suddenly, unexpectedly,
etc.) immediately discontinue use until it has been
checked by a factory authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and others by observing
all safety information, warnings, and cautions. Failure to comply with instructions could result in personal injury and/or damage to product or property.
Please retain instructions for future reference.
Operating Instructions and Parts Manual 25712
11/15
2015 OEMTOOLS
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
BATTERY-OPERATED
LIQUID TRANSFER PUMP
The following safety information is provided as a guideline to help you operate your Battery-Operated Liquid Pump under the safest possible conditions. Any
tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are not known or not followed. The following safety
instructions are to provide the user with the information necessary for safe use and operation. Please read and retain these instructions for the continued safe
use of your service system. Failure to follow instructions listed below may result in serious injury. In addition, make certain that anyone that uses the equipment
understands and follows these safety instructions as well.
Explanation of Safety Signal Words
CAUTION
WARNING
: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.
: Provide clarity and helpful information.
WARNING
CAUTION
NOTES
Thank you very much for choosing an OEMTOOLS Product!
For future reference, please complete the owner’s record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin
using it. This product is designed for certain applications only. OEMTOOLS cannot be responsible for issues arising from modification. We strongly
recommend this product is not modified and/or used for any application other than that for which it was designed. If you have any questions
relative to a particular application, DO NOT use the product until you have first contacted OEMTOOLS to determine if it can or should be
performed on the product.

2
Operating Instructions and Parts Manual 25712
11/15
2015 OEMTOOLS
BATTERY-OPERATED
LIQUID TRANSFER PUMP
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your tool. Read this manual carefully. Learn the tool’s
applications and limitations, as well as, potential hazards specific
to it.
2. Keep work area clean and well lit. Cluttered or dark work areas
invite accidents.
3. Keep children away. All children should be kept away from the work
area. Never let a child handle a tool without strict adult supervision.
4. Do not operate this tool if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment
or reflexes are impaired while taking drugs. If there is any doubt, do
not attempt to operate.
5. Use safety equipment. Eye protection should be worn at all times
when operating this tool. Use ANSI approved safety glasses.
Everyday eyeglasses are NOT safety glasses. Dust mask, non-skid
safety shoes, hard hat or hearing protection should be used in
appropriate conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-ties, rings,
bracelets or other jewelry may present a potential hazard when
operating this tool. Keep all apparel clear of the tool.
7. Don’t overreach. Keep proper footing and balance at all times when
operating this tool.
8. Check for damage. Check your tool regularly. If part of the tool is
damaged it should be carefully inspected to make sure that it can
perform its intended function correctly. If in doubt, the part should
be repaired. Refer all servicing to a qualified technician. Consult
your dealer for advice.
9. Keep away from flammables. Do not attempt to operate this tool
near flammable materials or combustibles. Failure to comply may
cause serious injury or death.
10. Store idle tools out of the reach of children and untrained persons.
Tools may be dangerous in the hands of untrained users.
11. Maintain tools with care.
12. Keep tools dry and clean.
13. Properly maintained tools are less likely to bind and are easier to
control. Do not use a damaged tool. Tag damaged tools “Do not
use” until repaired.
14. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool’s operation.
15. If damaged, have the tool serviced before using. Many accidents are
caused by poorly maintained tools.
16. Use only accessories that are recommended by the manufacturer
for your model. Accessories that may be suitable for one tool may
become hazardous when used on another tool.
17. Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could
result in a risk of injury.
18. When servicing a tool, use only identical replacement parts. Use of
unauthorized parts or failure to follow maintenance instructions may
create a risk of injury.
19. Maintain a safe working environment. Keep the work area well lit.
Make sure there is adequate surrounding workspace. Keep the work
area free of obstructions, grease, oil, trash, and other debris. Do not
use this product in a damp or wet location.
20. Maintain labels and nameplates on this product. These carry
important information. If unreadable or missing, contact OEMTOOLS
for a replacement.
21. Keep the handle dry, clean, and free from brake fluid, oil, and
grease.
22. Before use, read and understand all warnings, safety precautions,
and instructions as outlined in the vehicle manufacturer’s service
manual. It is beyond the scope of this manual to properly describe
the correct procedure and test data for each vehicle.
23. Always perform vehicle service in a properly ventilated area. Never
run an engine without proper ventilation for its exhaust. Stop work
and take necessary steps to improve ventilation in the work area
if you develop momentary eye, nose, or throat irritation as this
indicates inadequate ventilation.
24. Engine parts that are in motion and unexpected movement of
a vehicle can injure or kill. When working near moving engine
parts, wear snug fit clothing and keep hands and fingers away
from moving parts. Keep hoses and tools clear of moving parts.
Always stay clear of moving engine parts. Hoses and tools can be
thrown through the air if not kept clear of moving engine parts. The
unexpected movement of a vehicle can injure or kill. When working
on vehicles always set the parking brake or block the wheels.
25. Be alert for hot engine parts to avoid accidental burns.
26. If you drove your car recently, fluids could be very hot. Allow at least
2 hours before you handle any fluids. Oil and coolant burns are very
dangerous.
27. Avoid accidental fire and/or explosion. Do not smoke near engine
fuel and battery components.
NOTE: The manufacturer declines any and all responsibility for damage
to vehicles or components if said damage is the result of unskillful
handling by the operator or of failure to observe the basic safety rules set
forth in the instruction manual.
DISPOSAL
At the end of the useful life of the Battery-Operated Liquid Transfer Pump,
dispose of the components according to all state, federal, and local
regulations.
PURPOSE
The OEMTOOLS Battery-Operated Liquid Transfer Pump can pump 5–6
quarts of liquid a minute, making it an ideal choice when standard power
is unavailable. Designed to pump gas, water, oil and other non-corrosive
liquids. Can be used in garage, basements, bathrooms, shop, yard,
aquariums and more.
PRODUCT SPECIFICATIONS
Flow (GPM): 1
Suction Tube: 1-1/8” diameter and 13-3/8” long
Discharge Hose
Length: 24”
Power: Uses 2 D-cell batteries (not included)
WARNING

3
Operating Instructions and Parts Manual 25712
11/15
2015 OEMTOOLS
BATTERY-OPERATED
LIQUID TRANSFER PUMP
CAUTION
This equipment is intended only for professional use by personnel trained
in performing the service functions for which it is has been designed.
This equipment is designed for servicing a variety of vehicles in a safe,
convenient manner. However, differences in vehicle makes and models
may make it impossible to use this equipment as it is intended.
DO NOT attempt to force the use of this equipment on an application for
which it is not designed to perform.The procedures documented in this
manual are to serve as guidelines for the use of this equipment.
In addition to these guidelines, always follow the manufacturer’s
recommended procedures when servicing each unique vehicle.
OPERATING INSTRUCTIONS:
1. Insert 2 “D” size batteries (not included) as shown in Diagram A.
2. Immerse the suction end of the pump into the liquid.
3. Insert the discharge hose into a container to receive the liquid.
4. Turn the switch to the On position to begin pumping. Be careful not
to fill the container too much. Shown in Diagram B.
BATTERY CAUTIONS:
1. Non-rechargeable batteries are not to be recharged.
2. All batteries used must be of the same brand and type.
3. Do not mix alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium) batteries.
4. Do not mix old and new batteries.
5. Remove old batteries.
6. Remove batteries when not in use.
CAUTIONS:
1. Do not run dry. Only switch the pump on after submerging the
suction end of the pump in liquid.
2. Do not turn the pump upside down after use.
3. Do not place the pumping container higher than the pump’s
batteries housing.
4. Rinse with water after use.
5. Store or use when the unit is thoroughly dry.
NOTE: In case any liquid backs up in the hose, it will drain from the
bottom of the “Overflow Outlet”. Keep hands away from these points.
Do not use this pump near an open flame while pumping gasoline.
MAINTENANCE:
1. Always store the Battery-Operated Liquid Transfer Pump in a well-
protected area where it will not be exposed to inclement weather,
corrosive vapors, abrasive dust or any other harmful elements.
2. Keep the Battery-Operated Liquid Transfer Pump clean for better
and safer performance.
OPERATING INSTRUCTIONS:
1. Insert 2 “D” size batteries (not included) as shown in Diagram A.
As shown in Diagram B:
1. Immerse the suction end of the pump into the liquid.
2. Insert the discharge hose into a container to receive the liquid.
3. Turn the switch to the on position to begin pumping. Be careful not to fill the container
toomuch.
BATTERY CAUTIONS:
1. Non-rechargeable batteries are not to be recharged.
2. All batteries used must be of the same brand and type
3. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium)
batteries.
4. Do not mix old and new batteries.
5. Remove old batteries.
6. Remove batteries when not in use.
CAUTIONS:
1. Do not run dry. Only switch the pump on after submerging the suction end of the
pump in liquid.
NOTE:
In case any liquid backs up in the hose,it will drain from the bottom
of the "Overow Outlet".Keep hands away from these points.
Do not use this pump near an open ame while pumping gasoline.
2. Do not turn the pump upside down after use.
3. Do not place the pumping container higher than the pump’s batteries housing.
4. Rinse with water after use.
5. Store or use when the unit is thoroughly dry.
ON
OFF
LIQUID
DISCHARGE HOSE
SUCTION END
OPERATING INSTRUCTIONS:
1. Insert 2 “D” size batteries (not included) as shown in Diagram A.
As shown in Diagram B:
1. Immerse the suction end of the pump into the liquid.
2. Insert the discharge hose into a container to receive the liquid.
3. Turn the switch to the on position to begin pumping. Be careful not to fill the container
toomuch.
BATTERY CAUTIONS:
1. Non-rechargeable batteries are not to be recharged.
2. All batteries used must be of the same brand and type
3. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium)
batteries.
4. Do not mix old and new batteries.
5. Remove old batteries.
6. Remove batteries when not in use.
CAUTIONS:
1. Do not run dry. Only switch the pump on after submerging the suction end of the
pump in liquid.
NOTE:
In case any liquid backs up in the hose,it will drain from the bottom
of the "Overow Outlet".Keep hands away from these points.
Do not use this pump near an open ame while pumping gasoline.
2. Do not turn the pump upside down after use.
3. Do not place the pumping container higher than the pump’s batteries housing.
4. Rinse with water after use.
5. Store or use when the unit is thoroughly dry.
ON
OFF
LIQUID
DISCHARGE HOSE
SUCTION END
CAUTION
CAUTION
WARNING

4
Operating Instructions and Parts Manual 25712
11/15
2015 OEMTOOLS
BATTERY-OPERATED
LIQUID TRANSFER PUMP
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.customerser[email protected]
OEMTOOLS®LIMITED 90 DAY WARRANTY
From 90 days from the original purchase of this product, OEMTOOLS will warranty this item. If you find any defect in material or workmanship, through
normal usage, return it to the place of purchase or to OEMTOOLS for repair or replacement at our discretion. In order to obtain this service send your
tool and proof of purchase, transportation pre-paid, to OEMTOOLS Q.A. Dept., 3580 E. Raines Road #3, Memphis, TN 38118. We will not be responsible
for lost or damaged goods during transportation, please insure your package. If our inspection verifies the defect, we will either repair or replace the
product at our election, or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty,
then you must bear the cost of returning the product.
OEMTOOLS does not provide warranty for products labeled other than OEM or OEMTOOLS. OEMTOOLS will not provide any warranty for products
subjected to abnormal use. Abnormal use includes, but is not limited to, abuse, accident, alteration, neglect, and unauthorized or unreasonable use or
repairs. This warranty does not cover bits, blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace
blades, bits, files, and batteries as necessary. OEMTOOLS reserves the right to makes any changes in construction or design at any time without any
obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that
this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the
use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
NOTE: Not all components of the Battery-Operated Liquid Transfer Pump are replacement items, but are illustrated as a convenient reference for
location and position in the assembly sequence.
Please read the following carefully.
OEMTOOLS and/or its distributors have provided the parts list and assembly diagram as a reference only. Neither OEMTOOLS and/or its distributors
make any representation or warranty of any kind to the buyer and/or user of this tool that he or she is qualified to do any repairs or replace any parts
of this product. OEMTOOLS and its distributors expressly state that all repairs or parts replacement should be done by certified or licensed technicians.
The buyer assumes all risk and liability arising out of his or her repairs or parts replacement to the original production.
(2) D Batteries
(Not Included)
On/Off
Button
Clear Hose