Oerlikon Leybold Vacuum DISPLAY ONE User manual

Torr
SP
Pa
mbar
8.8.8.8.
8.8.
DISPLAY ONE
DISPLAY ONE
Single Channel Vacuum Display
Catalog Numbers
230001
235001
Instruction Manual GA 09.034 / 2.02

0. Contents
0. Contents 1
0.1 List of Figures 3
0.2 List of Tables 3
1. Description 4
1.1 Validity 4
1.1.1 Catalog Number 4
1.1.2 Nameplate 4
1.2 Conforming Utilisation 4
1.3 Responsibility and Warrenty 4
1.4 Transport Damages 5
2. Safety 6
2.1 General 6
2.2 Signs and Symbols 6
2.3 Basic Safety Regulations 6
3. General Description 7
3.1 General Functional Characteristics 7
3.2 Applicable Transmitters 7
4. Technical Data 8
4.1 General Data 8
4.1.1 Mechanical Data 8
4.1.2 Environment 9
4.1.3 Standards 9
4.2 Mains Connection 9
4.3 Measuring Channel 9
4.3.1 Transmitter Powering 10
4.3.2 Measuring Technique 10
4.3.3 Switching Function 10
4.3.4 Analog Output 10
GA 09.034/2.02 – 07/10 1

5. Installation 11
5.1 Scope of Delivery 11
5.2 Mechanical Installation 11
5.2.1 Rack Installation 11
5.2.2 Benchtop Instrument 11
5.2.3 Panel Mounting 12
5.3 Connections 12
5.3.1 Rear of the Instrument 12
5.3.2 Mains Connection 12
5.3.3 Input 13
5.3.4 Analogue Output and Relay Output 13
6. Operation 14
6.1 Front Panel 14
6.2 Switching On and Switching OFF 14
6.2.1 Switching On 14
6.2.2 Switching Off 15
6.3 Operation Modes 15
6.4 Measurement Mode 15
6.4.1 Selection 15
6.4.2 Description 15
6.5 Parameter Mode 16
6.5.1 Selection 16
6.5.2 Description 16
6.5.3 Mass unit 16
6.5.4 Display Format 16
7. Maintenance and Servicing 17
7.1 Maintenance 17
7.1.1 General Maintenance Advices 17
7.2 Troubleshooting 17
7.2.1 Trouble Indication and Error Messages 17
7.2.2 Help in Case of Malfunctions 17
7.2.3 Exchange of fuses 17
7.2.4 Repair 17
8. Shelving and Waste Disposal 18
8.1 Packaging 18
8.2 Shelving 18
8.3 Waste Disposal 18
Annex 1 - EC Conformance Declaration
Annex 2 - Safety Information for the Reconsignment of Contaminated
Vacuum Devices and Components
Declaration of the Contamination (Form for Reconsignment)
2 GA 09.034/2.02 – 07/10

0.1 List of Figures
Figure 1 – Nameplate (example) 4
Figure 2 – Dimensions DISPLAY ONE (mm) 8
Figure 3 – Rear of the instrument 12
Figure 4 – Connector for Transmitter (RJ45) 13
Figure 5 –Connection for Analogue Output and Relay Output 13
Figure 6 – Front Panel 14
0.2 List of Tables
Table 1 – Catalog Numbers 4
Table 2 – Applicable Transmitters 7
Table 3 – Scope of Delivery 11
Table 4 – Display Structure and Description 14
Table 5 –Display of the Measuring Mode 15
Table 6 –Parameter Mass unit 16
Table 7 –Parameter Display Format 16
Table 8 – Error Messages 17
GA 09.034/2.02 – 07/10 3

1. Description
1.1 Validity
1.1.1 Catalog Number
This document is valid for the following products:
Catalog Number Product Version Serial Number
230001 DISPLAY ONE with mains cord, EU version 5.ff 10001 - 19999
235001 DISPLAY ONE with mains cord, US version 5.ff 10001 - 19999
Table 1 – Catalog Numbers
1.1.2 Nameplate
A nameplate is located on the bottom side of the instrument. When communicating with
Oerlikon Leybold Vacuum GmbH, the information on the nameplate will be needed. For
this reason enter the information here:
Figure 1 – Nameplate (example)
1.2 Conforming Utilisation
The DISPLAY ONE serves as a simple power supply and display unit for the transmitters
from the series THERMOVAC and PENNINGVAC.
1.3 Responsibility and Warrenty
Oerlikon Leybold Vacuum GmbH will assume no responsibility and warranty when the
operator or third parties
•do not observe the information provided in this document.
•do not use this product in line with the conforming utilisation
•modify the product in any way (modifications, repair work etc.)
•operate the product with accessories which is not listed in the corresponding
product documentation
The right of changes without prior announcement is reserved. The illustrations are not
binding.
4 GA 09.034/2.02 – 07/10

1.4 Transport Damages
•Check the packaging for visible damages
•Send an advice of damage to the carrier and to the insurer in case of damage
•Retain the packaging material, because the reconsignment in the original packaging of
the manufacturer is prerequisite for warranty claims
•Check the consignment for completeness
•Check the instrument for visible damages
WARNING: Damaged Product.
Starting a damaged product can be perilously.
GA 09.034/2.02 – 07/10 5

2. Safety
2.1 General
The DISPLAY ONE is supplied ready for operation. Even so, we recommend that you
carefully read these Operating Instructions so as to ensure optimum operating conditions
right from the start.
These Operating Instructions contain important information on the functions, installation,
commissioning, operation and troubleshooting of the DISPLAY ONE.
2.2 Signs and Symbols
Important remarks concerning operational safety and protection are emphasised.
DANGER or WARNING:
Information on the prevention of injury.
DANGER:
Information on the prevention of injury by electrical impact.
) REFERENCE:
General lead on further information and articles respectively.
2.3 Basic Safety Regulations
During all work, such as installation, maintenance and repair, please comply with
respective safety regulations.
DANGER: Mains voltage
Coming into contact with components inside the instrument carrying the mains
voltage can, when introducing object or liquids, cause danger to life.
WARNING: Improper usage
Improper usage can damage the instrument. Use the instrument only in
accordance to the manufacturers’ instructions.
WARNING: Incorrect connection and operation data
Incorrect connection and operation data can damage the instrument. Comply
with all prescribed connection and operation data.
6 GA 09.034/2.02 – 07/10

3. General Description
3.1 General Functional Characteristics
The DISPLAY ONE serves as a simple power supply and display unit for the transmitters
from the series THERMOVAC and PENNINGVAC.
3.2 Applicable Transmitters
The following transmitters can be operated via DISPLAY ONE:
Transmitter Type Display
THERMOVAC
TTR90, TTR90S
TTR91, TTR91S
TTR96
TTR211S
TTR216S
ttr
THERMOVAC TTR100, TTR100S2 ttr1
PENNINGVAC PTR90 Ptr90
Table 2 – Applicable Transmitters
GA 09.034/2.02 – 07/10 7

4. Technical Data
4.1 General Data
4.1.1 Mechanical Data
Dimensions: Width: 106.0 mm (1/4 19“)
Height: 84.5 mm (2 HE)
Depth: 108.0 mm
Weight: 0.5 kg
Build-in depth: ca. 150 mm (including connected plug)
Application: Rack installation
Panel mounting
Benchtop instrument
Figure 2 – Dimensions DISPLAY ONE (mm)
8 GA 09.034/2.02 – 07/10