office portfolio STANDESK MEMORY Series User manual

STANDESK MEMORY
STANDESK PRO MEMORY
ELECTRIC SIT-STAND WORKSTATION
Assembly Instructions
MODEL -
OP-MB- STANDESK MEMORY BLACK
OP–MB- STANDESK MEMORY WHITE
OP-MB- STANDESK PRO MEMORY BLACK
OP–MB- STANDESK PRO MEMORY WHITE
STANDESK PRO MEMORY
STANDESK MEMORY

M6 x 8
6Pcs+1 extra Pc M6 x 12
10Pcs+1 extra Pc 1 BAG
4mm
1 Pc
Put the leg (A) through the opening of the base (B)
Connect wiring as pictured in view “a" then push
back into the cavity.
1 Pc
VESA BRACKET
PLASTIC COVER
Turn the base upside down ON THE EDGE
Unscrew 4 screws to take off the rear ( narrow)
cover plate.
ABCD E F GH
IJ
B
IAllen key
B
OF A BENCH OR DESK.
Take out the electric wiring and plug from
underneath the plate.
The 4 screws (G) are already in place ready for
tightening.(Tighten later)
A
I
G
View a

Use 2 pcs M6*12 screws to assembly at the rear
of the base.
Now tighten 4 side screws as described in STEP 2.
X 2
X 1
B
A
I
G
Re assemble the narrow bottom cover (refer STEP1).
B
A
I
Place table panel assembly (part C) through center leg.
Assemble 6 pcs "E" screws but do not tighten.
Keep desk top panel in horizontal position and
then tighten all 6 pcs "E" screws.
6
A
B
C
E
I
Now turn over to the upright position.

Put plastic cover from the top of the leg.
Keep "standesk" in the front.
Connect spiral cord to the rear plug and screw
lock together.
J
X 4
Customer can choose to assemble VESA
BRACKET (part D) at high or low position.
D
I
G

LB
kg
≤110 lbs
(≤50 kg)
LB
kg
≤11 lbs
(≤5 kg)
！
CAUTION:DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY.
SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
LB
kg
≤2 2 lbs
(≤10 kg)
H
computer screen to the VESA BRACKET.computer screen to the VESA BRACKET.
9999
Raise platform.
Place rubber flange around leg column(between
base and platform) with opening facing the back
of the unit.
F

Fasten Wiring
www.officeportfolio.com.au
www.standesk.com.au
HD
There are 2 plastic clips behind the
assembly.
Loop the wiring through the top clip
and close, then loop the wiring
through the bottom clip and close.
M onitor spacers.
You will find a bag of 4 spacers and bolts.
This is included to allow for increased
monitor adj ustment should it be req uired.
Vesa monitor bracket
If the monitor is tilting because of its weight, the
centre Lock - nut in the centre of the bracket can
be adj usted to increase the resistance of the
monitor. Take off the plastic nut cap & tighten.
The more resistance will mean that it can carry a
heavier monitor.

1. Handset Display Symbols:
LED Height Display Screen (*features Energy saving Standby/Sleep function)
Key + :Up motion
Key - :Down motion
Key 1 : First memory setting
Key 2 : Second desired height setting
Key 3 : Third desired height setting
Key M :Key to set Memory
STEP 1 RESET PROCEDURE: THIS MUST BE DONE FIRST.
1. Press and hold the down motion key –on the handset until the desk reaches its
lowest height.
2. Long press (5 seconds) the down motion key –until the LED screen shows ”RSE”
and you hear a “beep”sound.
3. The LED screen will display the starting height as shown below.
RSE 15.0
Memory Setting Instructions

STEP 2 How to set your preferred height selections to Memory.
There are 3 memory settings and we recommend key 1 be the starting position
(lowest setting) for the Standesk.
Starting : Press Key M, (the LED screen will show “5 –“), then press (in quick
succession) Key 1 to memorise the starting height.
Eg.
To raise the height of the desk, press”Key +”until you reach the desired level.
To memorise this height, press “Key M”, then press (in quick succession) Key 2
or 3.
Eg.
Follow these instructions to set another height selection.
STEP 3 How to return to a programmed height setting.
To return to any programmed height setting, short press the Key (1,2 or 3) and the
desk will move to the location automatically.
M
5 - KEY 1
M 5 - KEY 2/3

MEASUREMENT CONVERSION (METRIC OR IMPERIAL)
PRESS/HOLD ( M ) 5-10 SECONDS. LED SCREEN WILL DISPLAY (FLASHING) ( 1 – 0 )
PRESS ( + ) ONCE TO SHOW ( 0 ) FOR CENTIMETRES OR PRESS ( - ) TO SHOW ( 1 ) FOR INCHES
TO MEMORISE DESIRED SETTING, PRESS/HOLD ( M ) 5-10 SECONDS.
ANTI-COLLISION SENSITIVITY
TO ENABLE ADJUSTMENT OF COLLISION SENSITIVITY :
PRESS/HOLD ( M ) 5-10 SECONDS. LED DISPLAY WILL SHOW A FLASHING ( 1–0 )
THEN PRESS ( M ) AND LED SCREEN WILL DISPLAY ( 2-2 ), (KEEP PRESSING “M” TO REACH 3 AND 4)
2 = GYROSCOPE SENSITIVITY,
3 = ANTI-COLLISION SENSITVITY – UP
4 = ANTI-COLLISION SENSTIVITY – DOWN
TO ADJUST SENSTIVITY, PRESS ( + ) OR ( - ) TO REACH DESIRED SETTING.
THE ADJUSTMENT SCOPE IS BETWEEN 0 – 8,
1 BEING THE MOST SENSITIVE,
8 BEING THE LEAST SENSTIVE.
0 WILL DISABLE THE FEATURE.
* THE FACTORY STANDARD SETTING IS 2
TO MEMORISE PRESS/HOLD ( M ) 5-10 SECONDS.
Additional Settings

2. Fault code & Solution:
E-1:Motor hall break or Signal problem.
E-2:Motor’s phase wire disconnect.
E-3: Motor unplug
E-4: Motor short circuit
E-5: Motor stalling
E-6: Motor hall direction doesn’t match phase wire
Solution: Change two hall wires

E-7: Control box problem
E-8: Handset disconnect
E-10: Screw rod to bottom or to topside
Solution: Reset
E-12: Electricity power down during working
E-13: Anti-collision function working