Oggi SG-26 User manual

OGGI SG-26
HARDWARE MOUNTED GATE
28,7’’ - 38’’
Oggi . 360 Stewart Road – Wilkes-Barre, PA 18706
5,5’’ 11’’
Extension
Sold separately
2
1
Extension
Please read the following instructions carefully.
Keep this instruction manual for future reference.
Tools required: Wrench (included).
WARNING:
Keep small parts away from children.
Adult assembly required.
Intended for use with children from 6 months through 24 months.
INSTRUCTION MANUAL
Thank you for purchasing this Safety Gate from Oggi.
This gate will help you create and maintain a secure environment for your child (or pets).
WARNING: IMPORTANT! KEEP FOR FUTURE REFERENCE!
WARNING: To prevent serious injury or death, securely install
gate and use according to manufacturer’s instructions.
WARNING: Never use with a child able to climb over or
dislodge/open the gate.
WARNING: Never leave child unattended.
Do not use if any components are missing or damaged.
Always close and lock gate behind you.
Do not use if any components are missing or damaged.
Intended for use with children from 6 months through 24 months.
This product will not necessarily prevent all accidents. Proper adult supervision is required at all times.
Adult assembly required. Exercise care when unpacking and assembling product.
•
•
•
•
•
•
!
!
110217-yanis-a5-userguide-oggi.indd 1 18.02.2011 15:44:40

OGGI SG-26
HARDWARE MOUNTED GATE
FEATURE & COMPONENTS
SET-UP
This gate is suitable for openings between 28.7’’ and 38’’ wide.
Step 1
Attach the wall-cup screws ‘A’ and the nuts ‘B’ through the
casings ‘D’ to the four corners of the gate.
Step 2 & 3
Fix the wall-cups ‘C’ to the wall surface using the appropriate
fixings for the surface. The holes for the lower wall-cups should
be 0,8‘‘ above the floor while the holes for the upper wall-cups
should be 28,3‘‘ above the floor. Observe the orientation of the
upper and lower wall-cups.
Step 4
Place the gate into position. If the latch is not aligned correctly,
adjust the wall-cup screw next to the latch until the latch closes
securely.
Step 5
Adjust the wall-cup screws ‘A’ so that the two vertical supports
are at 90° to the bottom horizontal piece. Use a spirit level if
necessary. Tighten the nuts ‘B’ using the spanner ‘E’.
Dx4
Ax4 Bx4 Ex1
1
3
screws not provided
Cx4
BD
2
C
C
A
28,3’’
0,8’’
110217-yanis-a5-userguide-oggi.indd 2 18.02.2011 15:44:41

IMPORTANT ! KEEP FOR FUTURE REFERENCE
Step 6
The distance between the wall surface and the gate should be
no less than 0,5‘‘ and no more than 2,5‘‘ on both sides.
Step 7
To open the gate, slide the latch away from the wall and lift the
gate. The gate should open both ways. The arrows on the top of
the latch indicate the direction in which the gate can be opened.
Two orange arrows indicate that the gate is locked.
To block the opening direction of the gate switch the small lever
(located on the underside of the the latch mechanism) towards
the gate on the side in which you wish the gate to open.
Extensions
Refer to the table to see which extension(s) are required for the
desired opening.
To attach the extensions: Remove the nuts ‘B’, wall-cup screws
‘A’ and the casings ‘D’ on the latch side of the gate. Insert the
extension into the frame. Attach the wall-cup screws and nuts
to the extension.
Never climb over the gate
The gate is designed for indoor use only
This safety gate will not necessarily prevent all accidents. Never
leave children unattended
4
5
6
28,3’’
90° 90°
E
min 0,5’’
max 2,5’’
110217-yanis-a5-userguide-oggi.indd 3 18.02.2011 15:44:45

©2011 Oggi
Please retain for future reference.
Colors and styles may vary.
Made in Vietnam.
MAINTENANCE:
1. Regularly check gate, tension bolts and pads to make sure the gate is securely in place.
2. Do not use the gate if any components are damaged or missing.
To Clean:
Wipe surface with a damp cloth or sponge to clean.
2
J
5,5‘‘ 11‘‘2,8‘‘
7
110217-yanis-a5-userguide-oggi.indd 4 18.02.2011 15:44:47