OhmniLabs Ohmni User manual

For addional instrucons,
FAQs, videos, and more visit
our Helpdesk online:
CONGRATULATIONS ON THE PURCHASE
OF YOUR NEW
OHMNI
®
WHAT’S INSIDE
Everything you need to unpack, register
and drive your new Ohmni.
Navigaon
Camera
Hinge
Knob
Illuminated
Power Buon
Ohmni
Silent Drive
Charging
Contacts
Charging
Pins
Illuminated
Base
CHARGING
DOCK
Hex Key Wrench
AC Power Adapter
Main Camera
(Wide Angle 4K
Supercam)
Tilng
Neck
IPS Display
(Touchscreen)
© 2020 OhmniLabs. All rights reserved. Ohmni® is a registered trademark of OhmniLabs Inc.
GETTING
STARTED
Far-field Speaker
and Microphone
ohmnilabs.com/helpdesk
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device
could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
Manufacturers of U-NII devices are responsible for ensuring frequency stability such
that an emission is maintained within the band of operation under all conditions of
normal operation.
RF exposure warning
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter. End-users and installers
must be provide with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.
Canada, Industry Canada (IC) Notices
This device complies with Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Canada, avis d'Industry Canada (IC)
Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s).
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit
pas causer d'interférence et (2) cet appareil doit accepter toute interférence,
notamment les interférences qui peuvent affecter son fonctionnement.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC)
radio frequency exposure limits. The Wireless Device should be used in such a manner
such that the potential for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure
limits under mobile exposure conditions. (antennas are greater than 20cm from a
person's body).
Informations concernant l'exposition aux fréquences radio (RF)
La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite
d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil
de façon à minimiser les contacts humains lors du fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux limites d'exposition
aux RF d'IC dans des conditions d'exposition à des appareils mobiles (antennes sont
supérieures à 20 cm à partir du corps d'une personne).
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems
les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés
uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux

UNPACKING OHMNI
1 2 3
45
Remove the top supporng foam.
Carefully li Ohmni from its box. Then
remove the dock & accessories box.
PRO-TIP
Keep all packaging materials including hook-and-loop tape restraints.
Stand Ohmni on a flat surface and
remove the hook-and-loop tape
restraints from the tubing.
To turn Ohmni on, press the silver
buon located to the right side of the
speaker (opposite the hinge knob).
Once the power buon has been
pressed, the screen will light up along
with lights at the base.
To unfold Ohmni, pull & hold the hinge knob with one hand as you li the
rear tube halfway with the other hand. Now release the knob and connue to
li the tube to its full upright posion while listening for the hinge to
click/lock into place.
CAUTION
If you feel resistance when lifting the rear tube, STOP, return to the start
position, pull & hold on the hinge knob and try again.
THIS
SIDE
UP
STANDBY
DOCK
COLOR CODE CHARGING
Pull/roll Ohmni up against the dock making sure the silver charging pins on
Ohmni make contact with the charging contacts on the dock (listen for the
click). The charging dock will turn blue indicang charging.
PRO-TIP
Make sure your Ohmni is docked when not in use.
Complete your setup online. Create
a new account or login with an
exisng account by vising:
https://app.ohmnilabs.com
i