Stiga T8731 User manual

Please Do Not Return This Product To The Store!
Contact Escalade®Sports customer service department at:
Phone: [phone] Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE®SPORTS PRODUCT INFORMATION
2L-5038-02
ÓÒÒ
TABLE TENNIS TABLE
MODEL NO.
T8731 (ST3000)
1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting
holes may not align and parts may not easily fit together. Leave locknuts slightly loose until you are
instructed to tighten them.
4. Tools required for assembly: Phillips Screwdriver, Two 9/16” Wrenches, Two 7/16” Wrenches.
Note: Adjustable wrenches can be substituted for wrenches.
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2010 Escalade Sports
OWNER'S MANUAL

2
1/4"
Plastic
Washer Washer
Plastic
3/8"
28 30
31
32 5
34
35 37
1/4-20 X 3 1/4 Carriage Bolt #8 X 9/16
SMS
#8-32 X 1 1/4
Sheet Metal Screw 3/8" Long Spacer
3/4" Long Spacer
39
36
1/4-20 X 2 3/4 Hex Head Bolt
29
HARDWARE IDENTIFIER
3/8-16
Nyloc
Locknut 1/4-20 X 1 1/2 Phillips
Truss Head Screw
1/4-20 Nyloc
Locknut
27
3/8-16 x 3 1/2 Hex Head Bolt
3/8-16X2 3/4 Hex Head Bolt 1/4-20 X 2 1/2” Hex Head Bolt 3/8 Push Nut
Christmas
Tree Clip
13 24 11 23
(Qty. 4) (Qty. 20)
(Qty. 4)
(Qty. 12)
(Qty. 4) (Qty. 4) (Qty. 128)
(Qty. 4) (Qty. 4) (Qty. 4) (Qty. 8) (Qty. 8)
(Qty. 8) (Qty. 12 ) (Qty. 4) (Qty. 4)
38
(Qty. 4)
1/4-20 Wing Nut

115
64 "
111
64
" 1
11
64
"
1
15
64
"
8
10
10
43
8
11
9
10
1A. Attach Caster Wheels (#9 & #10) to Caster Beam. Slide a Caster
Wheel with Lock (#10) through Caster Beam (#8) and secure it with a
Push Nut (#11) as shown in Figure 1. Gently tap the Push Nut (#11)
with a hammer to secure it in place. On the other end of the Caster
Beam attach a Caster Wheel without Lock (#9). Make sure you have
one Caster Wheel with Lock and a Caster Wheel without Lock for each
Caster Beam. Repeat step for second Caster Beam.
2.
distance between middle holes to side holes is different, see Front
View of Figure 2. Attach Stop Spools (#12) and Support Plates
(#43) to side of Caster Beam without logo with Bolts (#13) and Nuts
(#28) but do not tighten completely. See Figure 2.
Repeat step for second Caster Beam.
Lay Support Plates (#43) on Caster Beam (#8) to line up holes, the
Figure 1
13
28
43
12
8
Longer
Shorter
Figure 2
Front View
3
Longer
Shorter
Match Support Plate (#43)
with Caster Beam (#8).
holes in
14
1B. Attach Tube Plugs (#14) to Caster Beam (#8) as shown in Figure 1.

4
3. Attach Wood Bottom Board (#15) to Caster Beam
Assemblies (#8) as shown in Figure 3. Turn
Caster Beams as shown and attach board with four
Carriage Bolts (#31) and four Wing Nuts (#32).
Tighten Wing Nuts securely.
READ AND FOLLOW ALL ASSEMBLY, OPERATING, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO (2)
ADULTS ARE NEEDED TO PUT THIS TABLE TOGETHER!
4. Attach Strut Tubes (#17) and Linkages (#16) to Caster Beam Assemblies (#8) as shown in Figure 4.
a) If necessary loosen Bolts (#13) and Nuts (#28) so that Strut Tube (#17) can fit between Support
Plate (#43) and Caster Beam (#8) as shown in the Top View and Figure 4.
b) Slide one Hex Bolt (#27) through Support Plate (#43), followed by one Plastic Washer (#39), Strut
Tube (#17), one Plastic Washer (#39), pass through Caster Beam (#8), one Spacer (#36), one
Linkage (#16), and Lock Nut (#28).
c) Repeat on other end of Caster Beam (#8) and on second Caster Beam.
d) Tighten Bolts (#13) and Nuts (#28) securely.
e) Tighten Nuts (#28) on Bolts (#27) securely.
NOTE: Tighten nuts so that end of Bolt (#27) in even with the edge of nut.
15
31
8
32
31
32
8
17
8
36
39
28
27
16
17
16
27
43
39 12
36
28
7
43
Note: Support Plate (#43)
is on the inside of Caster
Rail (#8) as shown.
13
8
43
28
13
Note: Linkages & Strut
tubes must be turned as
shown or table will not
operate correctly.
Figure 3
Figure 4
TOP VIEW

CAUTION:
WHEN ASSEMBLING TABLE, IT IS EXTREMELY IMPORTANT THAT THE U-
CLIPS (#22) BE TURNED AS SHOWN HERE. IF U-CLIPS ARE TURNED
INCORRECTLY, YOU WILL DO IRREPARABLE DAMAGE TO YOUR TABLE
WHEN YOU ATTEMPT TO OPEN IT TO THE PLAYING POSITION.
5. Lay Table Top (#1) painted side down, on a smooth, flat
surface. Use the shipping container to protect the painted
surface of table top.
6. Align the ”U” Support (#21) on Table Top (#1) as shown in
Figure 5.
7. Align all four holes in each U-Clip (#22) with the four pilot
holes in table top. Be sure that Slot in the Three U-Clips (#22)
all face the same direction toward the end of the table with no
stripe and no pilot holes. Secure U-Clips (#22) with Screws
(#5) as shown in Figure 5 & Detail A.
1
Note: End with no stripe
and no pilot holes.
Detail A
Detail B
Figure 5
8. Rotate U-support (#21) that is on bottom of Table Top until
you see the screw holes in the slots of U-clips (#22). If
necessary Slide U-support (#21) side to side and back and
forth to see holes. See Figure 5 & Detail B.
9. Insert Screw (#35) through slot in U-clip (#22) and into U-
support (#21). See Figure 5 & Detail B. Thread screw all the
way into U-support until it touches the back of the tube. There
should be about 3/8” of screw (#35) left sticking out. Repeat
for second Screw (#35) and U Clip (#22).
5
Note: To aid in assembly you can use a cordless drill and
Phillips bit for Step 9 only. Wear safety glasses.
22
5
21
21
22
35
Note: All four holes in the U-Clip (#22) must align with
four pilot holes in table top. See Detail A.

18
6
5
5
20
5
10. Assemble parts to the bottom of the table top with Screws (#5) as
shown in Figure 6, Detail C and Detail D.
a) Align the holes in the Leg Mounting Bracket (#20) with the holes
in the table. Be sure that the bracket is facing towards the side of the
table and attach with Screws (#5) as shown in Detail C.
b) Align the holes in the two U-Support Clips (#6) with pilot holes in
table top. Be sure that the two U-Support Clips (#6) are positioned
exactly as shown in Figure 6 & Detail D.
Figure 6
Detail C
Detail D
6
6
DO NOT USE A POWER DRIVER TO ATTACH HINGE
BRACKET ASSEMBLIES (#18) YOU COULD STRIP
SCREW IN WOOD AND DO IRREPARABLE DAMAGE
TO THE TABLE. DO NOT OVER TIGHTEN SCREWS
CAUSING THEM TO STRIP THE WOOD!
DO NOT USE A POWER DRIVER TO ATTACH HINGE BRACKET
ASSEMBLIES (#18) YOU COULD STRIP SCREW IN WOOD AND DO
IRREPARABLE DAMAGE TO TABLE. DO NOT OVER TIGHTEN
SCREWS CAUSING THEM TO STRIP THE WOOD!
holes in table top. Be sure that Hinge is facing the inside of the
table and placed exactly as shown in Figure 6 & Detail D.
c) Align the holes in the Hinge Bracket Assembly (#18) with pilot
NOTE: DO NOT use
a power driver to
attach hinge bracket
assemblies (#18).

23
2
4
Rail Tab
2
3
4
Figure 7
Detail E
Detail F
5
5
11. Lay out Rails (#2, 3 & 4) around edges of table top.
See Figure 7.
12. Line up Rail (#4) with Rail (#2). Make sure that Rail
Tab on Rail (#4) is on the inside of Rail (#2). Secure
Rails (#2) and (#4) by inserting a Christmas Tree Clip
(#23) into both rails as shown in Detail E. Repeat for
Rails (#3) & (#4).
13. Line up holes in rails with pilot holes in table top and
secure using Screws (#5). See Figure 7 & Detail F.
23
7
Note: Be sure square holes in Side Rails (#2 & #3)
are located as shown in Figure 7, Detail E & F.
Square hole on
this end
Square hole
on this end

14.
(#24) and Nuts (#34) as shown in Figure 8. Be sure that
the offset holes in (#19) Legs match each other as shown
in Detail G.
Assemble Cross Tube (#25) to Legs (#19) with Hex Bolts
Figure 8
34
24
19
25
19
Detail G
shorter distance
15.
shown in Figure 8.
Attach leg caps (#26) to bottom of the legs (#19) as
26
8

24
19
20
34 38
Detail J
Figure 9
16. Place Leg Assembly (from previous step) on table top. Be sure that
the offset holes in (#19) legs are closest to the table. See
Figure 9 & Detail H.
17. Attach leg Assembly (from previous step) to Bracket (#20) with Hex
Bolt (#24), Plastic Washer (#38) and Locknut (#34) as shown in
Detail I & Detail J. Tighten the Locknuts (#34) all the way but be
careful not to over tighten as you could bend the Leg (#19).
Detail H
19
shorter distance
Closest to the table
9
18. Repeat steps 10 through 17 to complete second Table Top Assembly.
Bolt (#24) goes in
the top hole of
Bracket (#20)
24
Detail I
20
NOTE: Prepare an area for the assembly of the second table top half. If
necessary, move the first table top half aside with the aid of a helper. Be sure
to place it in a location where it won't be disturbed or damaged. If setting on
its side, be sure to place the bottom edge no less than 12 inches away form
the wall. Also be sure to place carpet or pieces of the shipping carton down to
protect table top edges. If floor is not carpeted, brace table top half with a
heavy object to keep it from sliding.

10
19. Attach Table Top Assembly to Base Assembly as
shown in Figure 10. Pivot Strut Tubes (#17) up as
shown; then, with at least one adult on each side of
Table Top, lift top and align ends of U-support tube
(#21) with tops of Strut Tubes (#17) on Caster
Beams (#8) as shown in Figure 10. Slide tubes
together.
DO NOT OPEN THE TABLE TO PLAYING POSITION
UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
TABLE STANDING UNATTENDED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.
AT LEAST TWO (2) ADULTS ARE NEEDED TO
COMPLETE THE REST OF THIS ASSEMBLY! WHEN
ASSEMBLING TOPS TO BASE, HANDLE TOP
ASSEMBLIES BY GRASPING ONLY THE TOPS
THEMSELVES. DO NOT GRASP METAL LEGS, U-
SUPPORT, LINKAGE, OR HINGES. THESE PARTS
CAN MOVE AND COULD PINCH FINGERS OR
HANDS CAUSING SERIOUS INJURY! ASSEMBLE
AS SHOWN WITH LEGS FULLY CLOSED AND
TOPS IN A VERTICAL POSITION. DO NOT OPEN
Y TO ASSEMBLE. TABLE TOPS ARELEGS AND TR
HEAVY -
ALONE!
DO NOT ATTEMPT TO ASSEMBLE
TUBES UP
Table Top
Assembly
21
U-Support
17
Strut Tube
8
8
With at least 2 adults,
slide Table Top Assembly
onto Strut Tubes (#17).
17
Strut Tube
PIVOT STRUT
Figure 10

11
20. Screw U-support tube (#21) to Strut Tubes (#17) with two Screws
(#5) as shown in Figure 11. Align holes in U-support with holes
in Strut Tubes and thread screw (#5) into hole in Strut Tube
(#17). Tighten screws all the way but be careful not to over
tighten as you could strip threads on screws.
21. Attach Hinges (#18) to Strut Tubes (#17) as shown in Figure
11 & Detail L. With hinge positioned as shown, align hole in
hinge with hole in Strut Tube and attach with ¼” Screw (#30),
Plastic Washer (#38) and Locknut (#34). Plastic Washer (#38)
goes between Strut Tube and Hinge. Tighten nut securely. Repeat
for other Hinge. CAUTION: Hinges must be positioned
exactly as shown or table will not operate correctly and
could be damaged. DO NOT take Hinges off.
24. With at least two adults, repeat steps 19
through 23 for other table top assembly..
22. Attach Linkages (#16) to Leg (#19) as shown in
Figure 11. Pivot Leg (#19) out from the table top
and pivot both linkages (#16) up and align hole in
Linkage with hole in Leg (#19). Attach Linkage
(#16) to Leg (#19) using Hex Head Bolt (#29),
Spacer (#37) and Locknut (#34). Spacer (#37)
goes between Linkage and Leg. Attach other
Linkage to Leg the same way. Tighten nuts securely.
29
16
16
18
Hinge Assembly
18
Hinge Assembly
34
34
21
5
17
17
38
Plastic Washer goes
between Strut Tube
(#17) and Hinge (#18)
40
Spacer goes between
Linkage Arm (#16) and
Leg (#19)
37
16
19
29
5
CAUTION: Position hinges exactly as
shown in Detail L or table will not
operate correctly and could be damaged.
23. Attach Corner Protector (#40) to table corners.
Push snap tabs on Corner Protector into holes in
rails. Be sure that tabs are aligned with holes
before pushing. You could break tabs if they are
not aligned correctly.
34
38
30
18
17
30
38
34
30
18
17
Detail K
DO NOT OPEN THE TABLE TO PLAYING POSITION UNTIL
BOTH TOPS ARE INSTALLED! DO NOT LEAVE TABLE
STANDING UNATTENDED. IT COULD BE KNOCKED OVER
CAUSING SERIOUS BODILY INJURY OR PROPERTY DAMAGE.
ATTENTION: If hinge is positioned as
shown below (Detail K), Rotate the hinge
as shown in Detail L. Do not take hinge off.
Detail L
Note:
hinge to the position shown in Detail L. DO NOT unscrew the hinge, you can rotate
the hinge without unscrewing it from the table.
If hinge (#18) is positioned as shown in Detail K, you will have to rotate the
If you want to see a video on how to position Hinge (#18) go to:
http://www.escaladesports.com/customer-service/videos.html
Incorrect position
of hinge
Correct position
of hinge
Figure 11
In the correct position
Hinge #18 will look like a
“V” when attached to Strut
Tube (#17).
37

12
CAUTION:
TO CLOSE:
1. Remove net and net posts from table.
2. Unlock all four hinges.
3. Lift one table half to midpoint until the
plastic clips are engaged. Then continue
lifting until closed.
4. Raise other table half in the same manner.
as shown in Figure 15.....
TO OPEN:
1. Hold center of top edge. Gently pull outward to midway position.
Continue to pull until disengaged from plastic clips and legs rest on the
floor as shown in Figure 12A and 12B. Do not leave table partially
opened at midway position.
2. Lower second top as described in step 1.
3. Lock all four center hinges. See Figure 13.
4. Attach net posts and net to table as shown in Figure 14.
NOTE: Net will be tight. It will be necessary to stretch net. This will insure
proper net tension.
....
....
....
PLAYING POSITION
IF TABLE IS NOT ALIGNING CORRECTLY: (see Figure 16)
1. Set the table to the Playing Position and lock hinges as shown in
Figure 13.
2. Loosen Wing Nuts (#32) attached to bolt (#31) in order to create
enough slack to align table tops. See Figure 3.
3. With the help of two other adults, push the two table top halves so
they are in line with each other and re-tighten the Wing Nuts (#32) as
shown in Figure 16.
....
....
....
....
OPENING AND CLOSING INSTRUCTIONS
Push to lock hinge.
Plastic
Clip
EXERCISE CAUTION IN OPENING/CLOSING TABLE. SMALL CHILDREN, OR
CHILDREN NOT PROPERLY INSTRUCTED IN ITS USE, MUST NOT BE ALLOWED TO OPEN/CLOSE
TABLE. IMPROPER HANDLING AND MISUSE CAN RESULT IN SERIOUS INJURY OR DAMAGE.
DO NOT CLIMB, STAND, OR JUMP ON TABLE. MOISTURE AND CONDENSATION WILL
DAMAGE PLAYING SURFACE OF THIS TABLE. STORE IN DRY, INDOOR PLACE.
Midway
Position
PLAYBACK POSITION
Hinge
Locked
To lock hinge push up on
the table and push hinge
as shown in Figure 12B.
STORAGE POSITION

13
ONE YEAR LIMITED WARRANTY
This consumer warranty extends to the original consumer purchase of any ESCALADE®SPORTS Product
(hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of one (1) year from the original
purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free from
defects in material and workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE
PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW IN-
STRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND WORK-
MANSHIP.
WARRANTY PERFORMANCE: During the above one (1) year warranty period, ESCALADE SPORTS shall repair or replace with a
comparable model, and Product, or component thereof, which may prove defective under normal use and proper care, and which our
examination shall disclose to our satisfaction to be thus defective, please contact our Warranty Dept.
arranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
[e-mail]
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty Products. ESCALADE® SPORTS
strongly recommends that the Product is insured for value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE
ABOVE ONE (1) YEAR WARRANTY PERIOD. ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR
OTHER CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the above
limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
CARE AND MAINTENANCE
You have purchased a quality product that will give you years of enjoyment. By following these simple maintenance steps, you will add to the life of your new table.
THE TABLE TOP
The top (playing surface) of your table is made of particle board or MDF. Like all products made of wood, it can be affected by atmospheric changes in both temperature and
humidity. This may cause a slight sag or distortion as the top expands or contracts. This is normal and should not cause concern as it does not detract from the play or utility value
of the table. After assembly of the table, you can minimize the effects of temperature and humidity changes by storing the table in the folded up position in a dry area when table
is not in use.
STORAGE OF YOUR TABLE
This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme temperature changes can cause the wood to warp, swell, crack or blister.
When your table is not in use, it should be folded up in a dry area. Due to the nature of particle board, table top may bow. Damp and humid conditions will amplify this. This is
normal and will not affect playability of table.
CLEANING YOUR TABLE
To clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table's playing surface, DO NOT USE ANY CHEMICALS, ABRASIVE OR CLEANING
PRODUCTS on your table's playing surface.
MAINTENANCE OF YOUR TABLE
Be sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease of use of your table.
This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme temperature changes which occur on patios or similar areas can cause wood
to warp, swell, crack or blister.
UNLEVEL FLOORS
If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING POSITION and move table several inches in different directions to find the
best location for the table. If the floor is extremely unlevel, table may not play or operate properly. If table is high in the center, shim up under the outer U-legs.
1-866-873-3528 / W

4
2
3
1
5
24
38
34
29
24
26
30
38
34
5
6
22
5
21
20
5
23
40
5
5
3437
34
2
3
4
18
25
19
2L-5038-02
Key# Part # Description Qty.
4A-5470-00
2S-9108-02
2S-9109-02
2S-9107-01
1B-4082-99
3M-6273-00
8S-6841-02
2Q-4017-00
2Q-4018-00
2B-4043-00
3M-6884-00
1B-6195-00
3M-6274-00
2W-6258-03
8S-6842-02
8S-6850-05
4A-5423-02
8S-6866-01
2S-4597-01
8S-6851-01
2S-6879-10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
3/4" BLUE TOP ONLY
SIDE RAIL - RIGHT HAND
SIDE RAIL - LEFT HAND
END RAIL
#8 X 9/16 SHEET METAL SCREW
U-SUPPORT CLIP (PLASTIC)
NOT USED
CASTER BEAM ONLY
3" CASTER - NON LOCKING
3" CASTER - WITH LOCK
3/8" PUSH NUT
STOP SPOOL
3/8-16 X 2 3/4 HEX HEAD BOLT
TUBE PLUG - 1" X 2"
BOTTOM BOARD
LINKAGE
STRUT TUBE
HINGE & MOUNTING BRACKET ASSEMBLY
LEG-BLUE
MOUNTING BRACKET ONLY
U SUPPORT
1" U-CLIP
2
2
2
2
128
8
2
2
2
4
8
8
4
1
4
4
4
4
8
2
6
Replacement Parts List for Model Number T8731
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
3M-5025-00
1B-4137-00
1A-6341-01
3M-6248-00
1B-6495-00
2B-4053-00
1B-4135-00
1B-4097-01
1B-6459-00
1N-0001-00
2B-4047-98
1B-4089-00
7B-4061-00
7B-6161-00
2B-6087-00
2B-4054-00
3M-6715-00
5A-6700-02
2L-5038-02
2S-6875-02
CHRISTMAS TREE CLIP
1/4-20 x 2 1/2”HEX HEAD BOLT
CROSS TUBE
2" SQUARE PLUG
3/8-16 x 3 1/2 HEX HEAD BOLT
3/8-16 NYLOC JAM NUT
1/4-20 x 2 3/4 HEX HEAD BOLT
1/4-20 x 1 1/2 PHILLIPS HEAD SCREW
1/4-20 X 3 1/2 CARRIAGE BOLT
1/4-20 WING NUT
NOT USED
1/4-20 NYLOC JAM NUT
#8-32 x 1 1/4 SHEET METAL SCREW
3/4 OD X 13/32 ID X 3/4 LONG SPACER
1/2 OD X 9/32 ID X 3/8 LONG SPACER
1/4" PLASTIC WASHER
3/8" PLASTIC WASHER
CORNER PROTECTOR
66" NET & POST SET (NOT SHOWN)
OWNERS MANUAL - T8731
SUPPORT PLATE
4
12
2
4
4
12
4
4
4
4
20
4
4
4
8
8
4
1
1
4
8
13
14
10
16
17
16
8
9
16
27
12
39
32
17
17
31
28
36
13
43
28
16
17
15 11
14

2L-5038-02
ÓÒÒ
2010 Escalade Sports
Por favor NO devuelva este producto a la tienda!
MANUAL DEL USARIO
Los productos Escalade® Sports se pueden fabricar y/o producir bajo las siguientes patentes.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Puede haber patentes en trámite. Una o más patentes mencionadas y/o en trámite pueden cubrir productos específicos.
MESA
NÚMERO DE MODELO
T8731 (ST3000)
DE TENIS
1. Lea este manual cuidadosamente antes de empezar a ensamblar. Lea completamente cada uno de los
pasos antes de empezar cada paso.
2. Algunas partes pequeñas pueden ser empacadas dentro de las partes grandes . Verifique en el
interior de todas las partes y cartones antes de ensamblar o solicitar partes.
3. No ajuste las partes hasta que las instrucciones se lo indiquen. Si las partes se ajustan antes de lo
indicado, es posible que los hoyos no queden alineados y las partes queden fuera de su lugar. Deje las tuercas
levemente flojas hasta que las instrucciones le indiquen ajustarlas.
4. Herramientas necesarias: ” ”Desarmador Phillips, dos llaves de 9/16 y dos llaves de 7/16 (Puede utilizar una
llave ajustable en vez de llaves).
Contacte el departamento de servicio al cliente de Escalade® Sports:
Teléfono: 1-800-467-1245 ¡Sin costo alguno!
Fax: [phone] ¡Sin costo alguno!
Correo Electronico: [email protected]
Apartado postal (sólo para correspondencia):
Escalade Sports
PO Box 889
Evansville, IN 47706
Visite nuestra página Web internacional: www.escaladesports.com
SOLUCION DE PROBLEMAS POR INTERNET ASISTENCIA TÉCNICA
PEDIDO DE PARTES POR INTERNET PREGUNTAS FRECUENTES
MÁS INFORMACIÓN SOBRE PRODUCTOS DE ESCALADE® SPORTS

2
28 30
31
32 5
34
35 37
39
36
29
IDENTIFICADOR DE TORNILLOS
27
13 24 11 23
(Cant. 4) (Cant. 20)
(Cant. 4)
(Cant. 12)
(Cant. 4) (Cant. 4)
(Cant. 4) (Cant. 4) (Cant. 4) (Cant. 8) (Cant. 8)
(Cant. 8) (Cant. 12) (Cant. 4) (Cant. 4)
38
(Cant. 4)
3/8-16 x 3 1/2 Tornillo de Cabeza Hexagonal 1/4-20 Tuerca
de Seguridad
3/8-16
de Seguridad
Tuerca
1/4-20 X 2 3/4 Tornillo de Cabeza Hexagonal
1/4-20 X 3 1/4 Tornillo de Carruaje
1/4-20 X 1 1/2 Tornillo Phillips
1/4-20 Tuerca de Mariposa (Cant. 128)
#8 X 9/16
Tornillo SMS
3/8-16X 2 3/4” Tornillo de
Cabeza Hexagonal 1/4-20 X 2 1/2” Tornillo de
Cabeza Hexagonal
Contratuerca
de 3/8”
Clip
en forma de
Árbol de
Navidad
#8-32 X 1 1/4
de metal
Tornillo para lamina
Separador de 3/4” Separador de 3/8”
1/4"
Rondana
Plastico
de
3/8"
Rondana
Plastico
de

115
64 "
111
64
" 1
11
64
"
1
15
64
"
8
10
10
43
1A. Adjunte las llantas (#9 y #10) a el Carril. Deslice una llanta con
seguro (#10) a través de Carril (#8) y asegurela con una Contratuerca
(#11) como se muestra en la Figura 1. Golpe la Contratuerca (#11)
ligeramente con un martillo para asegurarla en su lugar. En el otro
extremo del carril adjunte una llanta sin seguro (#9). Asegúrese que
cada carril tenga una llanta con seguro y una llanta sin seguro.
Repita el paso para el segundo Carril.
Figura 1
13
28
43
12
8
Más Corto
Figura 2
3
Más Largo
Alinee los orificios de la Placa de
Soporte (#43) el con Carril (#8).
Vista Frontal
2.
orificios, la distancia entre los orificios centrales de los orificios
laterales es diferente, vea la Figura 2 y la Vista Frontal. Adjunte los
Carretes (#12) y las Placas de Soporte (#43) del lado del Carril sin el
logotipo, con los Tornillos (#13) y las Tuercas (#28) pero no los
apriete completamente. Vea la Figura 2. Repita el paso para el
segundo Carril.
Coloque las placas de soporte (#43) en el Carril (#8) para alinear los
Más Corto
Más Largo
8
11
9
10 14
1B. Inserte los Tapones (#14) al Carril (#8) como se muestra en la
Figura 1.

4
15
31
8
32
31
32
8
17
8
36
39
28
27
16
17
16
27
43
39 12
36
28
7
43
13
8
43
28
13
Figura 3
Figura 4
Vista de Arriba
ADVERTENCIA!
LEA Y SIGA TODAS LAS INSTRUCCIONES DEL
ENSAMBLADO, LAS OPERACIONES Y LAS INSTRUCCIONES
DE SEGURIDAD. POR LO MENOS SE REQUIERE DE DOS (2)
ADULTOS PARA ENSAMBLAR LA MESA!
3. Una la Tabla Inferior (#15) a el Carril con Llantas (#8)
como esta mostrado en la Figura 3. Voltee los
Carriles como están ilustrados y una la Tabla Inferior
con los cuatro Tornillos de Carruaje (#31) y las cuatro
Tuercas de Mariposa (#32). Atornille tuercas
asegurándose que estén apretadas y seguras.
Nota: La placa de Soporte
(#43) debe de estar en el lado
de adentro del carril con llantas
(#8) como está mostrado.
4. Una los Tubos Estructurales (#17) y los Tubos Conectores (#16) a los Carriles con Llantas (#8) como están mostrados en la
Figura 4.
a) Si es necesario afloje los Tornillos (#13) y Tuercas (#28) para que el Tubo Estructural (#17) pueda caber entre la Placa de
Soporte (#43) y Carril con Llantas (#8) como esta mostrado en la Vista de arriba y la Figura 4.
b) Deslice un Tornillo de Cabeza Hexagonal (#27) Placa de Soporte Interior (#43), seguida por una Rondana de Plástico
(#39), Tubo Estructural (#17), otra Rondana de Plástico (#39), el Carril con Llantas (#8), Placa de Soporte Exterior (#43) un
Separador (#36), Tubo Conector (#16), y Tuerca de Seguridad (#28).
c) Repita en el otro lado del Carril (#8) y en el segundo Carril con Llantas.
d) Apriete Tornillos (#13) y Tuercas (#28) hasta que queden asegurados.
e) Apriete Tuercas (#28) en los Tornillos (#27) hasta que queden asegurados.
NOTA: Apriete tuercas hasta que el extremo del tornillo (#27) quede al mismo nivel que el borde de la tuerca.
Nota: Tubos Conectores y Tubos
Estructurales deben de estar volteados
como esta mostrado, si no la mesa no
operara correctamente.

5. Coloque el Tablero (#1) sobre una superficie lisa y plana con
el lado pintado hacia abajo. Use la caja para proteger la
pintura de la superficie del tablero.
6. 6. Alinee el tubo de soporte "U" (#21) sobre el Tablero (#1)
como se muestra en la Figura 5.
7. Alinee los cuatro orificios en cada abrazadera en “U” (#22)
con los cuatro orificios en el tablero. Asegúrese de que la
ranura de las abrazaderas en “U” (#22) apunten en la misma
dirección hacia el extremo del tablero sin raya y sin orificios.
Asegure las abrazaderas en “U” (#22) con los Tornillos (#5)
como muestra en la Figura 5 y en el Detalle A.
Detalle A
Detalle B
Figura 5
5
8. Gire el tubo de soporte "U" (#21) que se encuentra en la base
del tablero, hasta que vea los orificios atravez de las
abrazaderas en “U” (#22) para los tornillos. Si es necesario
deslice el tubo de soporte "U" (#21) de lado a lado y hacia atrás
y adelante para ver los orificios. Ver la Figura 5 y el Detalle B.
9. Inserte el tornillo (#35) por la ranura de la abrazadera en “U”
(#22) y dentro del tubo de soporte "U" (#21). Vea la Figura 5 y
el Detalle B. Atornillelo hasta que toque el fondo del tubo de
soporte. El tornillo (#35) quedará afuera acerca de 3/8". Repetir
para el segundo tornillo (#35) y la abrazadera en “U” (#22).
Nota: Para facilitar el ensamblado se puede utilizar un
taladro inalámbrico y una broca Phillips únicamente
para el paso 9. Use anteojos de seguridad.
ADVERTENCIA:
CUANDO ENSAMBLE LA MESA, ES EXTREMADAMENTE IMPORTANTE QUE TODAS
LAS ABRAZADERAS EN “U” (#22) ESTÉN PUESTAS COMO ESTÁN MOSTRADAS EN
LA FIGURA DE ABAJO. SI LAS ABRAZADERAS EN “U” ESTÁN COLOCADAS
INCORRECTAMENTE, USTED LE OCASIONARA DAÑOS IRREPARABLES A SU MESA
CUANDO TRATE DE ABRIRLA EN LA POSICIÓN DE JUEGO.
Note: Extremo sin raya
y sin orificios de guía.
1
22
5
21
21
22
35
Nota: Los cuatro orificios en el la abrazadera en U (#22) deben de
estar alineados con los cuatro orificios en el Tablero. Vea el Detaille A.

20
5
Figura 6
Detalle C
Detalle D
6
18
6
5
5
6
10. Ensamble las partes a la base del tablero como se
muestra en la Figura 6, Detalle C y Detalle D.
a) Alinee los orificios del Soporte de Montaje de la Pata (#20) con los
orificios del tablero. Asegúrese que el soporte de montaje quede dirigido
hacia el lado de la mesa y sujetelo con los Tornillos (#5) como se
muestra en el Detalle C.
b) Alinee los orificios de los dos Clips de Plástico (#6) con los orificios de
guía del tablero. Asegúrese de que los dos Clips de Plástico (#6) estén
puestos exactamente como se muestra en la Figura 5 y el Detalle D.
con los Tornillos (#5)
NO USE UN TALADRO ELECTRICO PARA COLOCAR
LA BISAGRA (#18) PODRÍA BARRER EL TORNILLO EN
LA MADERA Y PUEDE CAUSAR DAÑOS IRREPARABLE
A LA MESA. NO APRIETE DEMASIADO LOS
TORNILLOS POR QUE PUEDEN DAÑAR LA MADERA!
NO USE UN TALADRO ELECTRICO PARA COLOCAR LA BISAGRA (#18)
PODRÍA BARRER EL TORNILLO EN LA MADERA Y PUEDE CAUSAR
DAÑOS IRREPARABLE A LA MESA. NO APRIETE DEMASIADO LOS
TORNILLOS POR QUE PUEDEN DAÑAR LA MADERA!
c) Alinee los orificios de la Bisagra (#18) con los orificios de guía que
están en el tablero. Asegúrese que la bisagra este dirigida hacia el
interior de la mesa y que se coloque exactamente como se muestra en la
Figura 5 y el Detalle D.
NOTA: NO USE UN
TALADRO ELECTRICO
PARA COLOCAR LA
BISAGRA(#18).