Oki OK-NICP-AE User manual

0
OK-NICP-AE
OK-NICP-AEP
OK-NICP-AEG – Wireless
OK-NICP-AEGP– Wireless
Pan Tilt MPEG4 IP Color Camera
Quick Installation Guide
This guide describes the basic functions of
Network Camera with Pan/Tilt.
All detailed information is described in the user’s manual.

1
Warning Before Install
◎ Power off the Network Camera as soon as it is found smoking or smelt unusual.
Contact your distributor when such cases happen.
◎ Keep the Network Camera away from the water. If the Network Camera is wet, power
off immediately.
Contact your distributor when such cases happen.
◎ Do not place the Network Camera around the heat sources, such as television or oven.
◎ Refer to your user’s manual for the operating temperature.
◎ Keep the Network Camera away from the direct sunlight.
Do not place the Network Camera in high humid environments.

2
Do not place the Network Camera on unsteady surfaces.
◎ Do not touch the Network Camera when it’s lightening.
◎ Do not disassemble the Network Camera.
◎ Do not drop the Network Camera.
◎ Do not manually pan and tilt the Network Camera when are power is on.
◎ Do not insert any object into the Network Camera, such as needles.

3
1. Check Package contents
◎ Wired or Wireless Network Camera
◎ Power adapter ◎Software CD
◎ Camera Mount Kit & Pads
◎ Quick Installation Guide ◎Antenna for wireless
modelonly

4
2. Physical description
◎ Front panel
◎Rear panel
Antennas (wireless model only)
Lens and manual focus ring
Microphone
Status LEDs
Antenna (wireless model only)
N
ote the serial number from the label on the unit.
This serial number is the same as the MAC address.
For example: 0002D000019=00-02-D1-00-00-19
Power Cord socketEthernet 10/100 RJ45 socket

5
3. Mounting the Camera
Ceiling Mount
1. Fix the camera to the bracket with the two supplied screws (type A).
2. Fix the bracket and camera to the ceiling using the two screws and hollow wall anchors.
3. If adopting POE kit (optional accessory) , the POE splitter can be attached to the bracket by using
the two supplied screws (type B)

6
Wall Mount
1. Fix the bracket to the wall using the two screws and hollow wall anchors.
2. Fix the camera to the bracket with the two supplied screws (type A)
3. If adopting POE kit (optional accessory), the POE splitter can be attached to the bracket by
using the two supplied screws * type B).

7
4. Install your Network Camera in Ethernet network
POWERCOLLISION
LINK
RECEIVE
PARTITION
12345
2. Connect power cord to a power outlet.
1. Use Ethernet cable to make connection from Ethernet port to the hub.
zUse Category 5 Cross Cable when the Network Camera is directly connected to PC.

8
5. Assign IP address
1. Run the Installer under the Utility directory from software CD.
2. The program will search the cameras on
the same LAN.
3. After searching, the main installer window
will pop up. Click on serial number that
matches the one you just note from
2. Physical description
4. Click “Link to selected device” to
connect the Internet Explorer to the
Network Camera.

9
6. The Internet Explorer Connects to the Network Camera

10
7. Set up Your Wireless Configuration for the Network Camera
(Wireless model only)
1. Check the SSID currently set on your wireless access point (AP).
2. Go to Configuration > Wireless LAN
Note:
1. SSID abbreviated from Service Set Identifier is the name to the wireless network. The
camera’s factory SSID setting is set to “default “.
2. Select ‘Ad-Hoc” wireless mode if you want the camera to communicate without using
an AP or wireless router.
For setup wireless mode and further configuration, please check user’s manual on the
software CD.
3. Type in the SSID consistent
with the setting on your AP.
4. Select t he wireless mode as
“Infrastructure”
5. Click Save

11
8. Client Settings (Windows 2000/Me/98E)
At the initial access to the “Connection type” page in Windows, the web
browser will ask for a new plug-in installation, the plug-in being the Network
Camera. This plug-in has been registered for certification and can be used
to change the parameters at the client’s site. The user may click on to install
the plug-in. If the web browser does not allow the user to complete the
installation, check the Internet security to lower the security level or contact
your IT or networking supervisor.
1. Initial IE browser, select function item “Tools”-> “Internet Options”
2. Security-> Default Level
3. Lower down the security level bar to “Low”, and press “Apply”

12
4. Refresh IE Browser, a question frame will pop-up to ask for downloadActive-X. press “Yes”.

13
9. Client Settings (Windows XP SP2)
1. Initial IE browser, select function item “Tools”→“Internet Options”
2. Security →”Custom Level”

14
3. Security Settings →Download unsignedActiveX Controls set “Enable” and press “OK”
4. Press “Apply” and then “OK”

15
5. Key-In camera’s IP address and press “OK” on Information Bar.
6. Click the blue bar under the Camera’s IPaddress in the browser, then
choose “Install ActiveX Control”
7. Recover security settings. Download unsignedActiveX Controls set
“Disable” and press “OK” and “Apply”