Oki SIG24-24843 Quick start guide

SIG24-24843_SIG24-24860_rev03102008
Operational Manual
Vandal Resistant IR Color Camera
z1/3” Hi-Res. CCD
z480 TV Lines
z24 IR LED / 850nm
z4.3mm or 6.0mm Aspherical Lens
z0.1 Lux @ F1.6 (0 Lux @ IR “on”)
zIR Distance up to 85ft / 26m
zIP66 Rating
zMulti Color Temperature for AWB
z12V DC
Unremovable Screw
Ceiling Installation
3D Rotary Bracket
1. Loosen the screw on the base and adjust rotationally.
2. Loosen the screw on the bracket and adjust the camera body
vertically. Each cog gears 18o.
3. Loosen the screw from the bottom and adjust the camera
horizontally. Each cog gears 18o.
NOTE: During step 1 or step 2, do not fully loosen the screw (only
loosen it enough to be able to adjust), or it will be difficult to tighten the
screw again.
SIG24-24843 4.3mm Lens
SIG24-24860 6.0mm Lens
SIG24-24843P
SIG24-24860P
FEATURES
Please read the Operational Manual
before attempting to use this product.
INSTALLATION
A
N
G
LE AD
JUS
TMENT

SIG24-24843_SIG24-24860_rev03102008
* When connecting the power line and video signal line, check to see if
power is 12V DC and monitor is at 75 ohm state.
* Turn on the power and then you can see video display on the monitor.
* Please do not loosen the screw on the camera or it will no longer be water
proof.
* Strong impacts may deform the unit and may cause malfunction to the
water proof feature.
* Please use 12V DC/350mA as the power supply to avoid heat damage or
power insufficiency.
* If water enters the unit or lens causing smoke, unusual heat or smells,
please contact your distributor.
Model SIG24-24843
SIG24-24860 SIG24-24843P SIG24-24860P
TV System NTSC PAL
Image Sensor 1/3” Hi-Res. CCD
Total Pixels 771(H) x 492(V) 753(H) x 582(V)
Video Output 1.0Vp-p / 75 ohms
Resolution 480 TV Lines
Minimum
Illumination 0.1 Lux @ F1.6 (0 Lux @ IR “on”)
Scan System 2:1 Interlace
S/N Ratio More than 48dB
Electronic
Shutter Auto and up to 1/100,000
Synchronization Internal
Gamma
Correction 0.45
Auto Gain Control Full Auto
Back Light
Compensation Full Auto
Auto White
Balance MCT-AWB (Multi Color Temperature AWB)
IP Rating IP66
Aperture
Correction 2H Mode of H.V aperture correction
Lens 4.3mm or 6.0mm Aspherical Lens
Distance Up to 85ft / 26m
Power Supply 12V DC
Power
Consumption 75mA + 10% IR 315mA + 10% under
Operation
Temperature -10oC ~ +45oC
Operation
Humidity RH 85% or less
Storage
Temperature -30oC ~ +60oC
Dimension 85mm(W) x 67mm(H) x 218mm(L)
Weight 850g
* Specifications are subject to change without notice.
zOne (1) SIG24-24843/SIG24-24843P or SIG24-24860/SIG24-24860P
Camera with power/video cable
zOne (1) Wrench Screw
zThree (3) Tapping Screws
zThree (3) Wall Anchors
zOne (1) Operational Manual
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this may
damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling could
damage the camera.
3. Requires a proper operating environment
This camera is designed for outdoor or indoor use. The allowable
temperature range for operation of this camera is between -10°C ~
50°C and the allowable humidity is 85%RH maximum.
4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned before
lens installation or whenever the lens is changed. Cleaning should be
done by using a chamois, a very fine soft cloth, lens tissue, or cotton
tipped applicator and ethanol to carefully remove any fingerprint or
dust.
5. Check the power source voltage
The power source voltage should be within the specified range.
(Camera must meet the specifications). Camera must be connected to
a surge protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may touch
dangerous voltage points of short out parts that could result in a fire
or electric shock. Never spill any kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all service to qualified servicing personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service to
qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video
product.
c. If the video product has been dropped or the cabinet has been
damaged.
d. When the video product exhibits a distinct change in
performance.
OKIUSA Products are covered under warranty for one year from the date
of purchase. The warranty will automatically be voided if any of the
following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm any
information regarding when and where the product was purchased.
We have no other way to verify the purchase record without the serial
number on the camera sticker; therefore, it should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner not
described in this manual, the warranty will be voided immediately. It is
the customer’s responsibility to keep the camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered with.
Cutting or modifying of the cables will result in termination of the
warranty.
CAUTION
SPECIFICATIONS
WARRANTY
CAUTION
LIST OF COMPONENTS