Oliver Furniture 021218 User manual

OLIVER FURNITURE / GEPPETTO A/S
Ndr. Strandvej 119 A
DK-3150 Hellebæk / Denmark
Tel. [phone]
Fax [phone]
[e-mail]
www.oliverfurniture.dk
ASSEMBLY INSTRUCTION / LOFT BED 021218
READ THE ASSEMBLY INSTRUCTION CAREFULLY BEFORE YOU START / OCT. 2010

PAGE 2
G.
A.
B.
I.
J.
H.
D.
F.
E.
C.
THE LOFT BED CONSISTS OF
6 BOXES:
1 x 031209
1 x 031207
1 x 031218
1 x 031214
1 x 031214
1 x 031219
THE BOXES FOR THE LOFT BED CONSIST
OF THE FOLLOWING PARTS:
A. 2 end board pieces
B. 2 short bars
C. 1 slatted bed case
D. 4 corner posts
E. 1 front bar
F. 1 back bar
G. 1 ladder
H. 2 sidepieces
I. 1 lower panel, long
J. 2 lower panels, short
Outside the boxes is a red string which indicates where the bags with the screws are placed in
the different boxes

PAGE 3
1.
3.
11.
14. 15. 16.
19.
1. 1 allen key
2. 6 screws for fixture of the ladder
3. 22 screws for the slatted bed case
4. 1 top nut
5. 1 spanner
6. 1 small connection screw
7. 16 washers for the connection screws
8. 16 spring washers
9. 2 fixtures for the ladder
10. 8 large plastic covers
11. 18 small plastic covers
12. 16 large wooden dowels
13. 14 small wooden dowels
14. 16 connection nuts
15. 8 nuts for the threads
16. 8 “half-moon” washers
17. 1 medium connection screw
18. 15 large connection screws
19. 8 threads for the corner posts
It is a good idea to assemble the loft bed on a smooth and even surface. Use the flamingo or the
cardboard from the packaging as underlay.
It is possible for 1 person to assemble the loft bed however we recommend that you are 2 persons.
Be aware that the loft bed is very exposed to lacquer damage on corners and edges due to all the
different pieces. erefore you must be very careful when assembling the loft bed.
Do NOT tighten the connections screws until the entire loft bed is assembled.
5.
2.
4.
6.
9.
7.
8.
10.
12.
13. 17.
18.
EXTRA SPARE PARTS MAY OCCUR

PAGE 4
In order to assemble the loft bed you will
need 1 screw driver, 1 hammer, and the
spanner and allen key which are both
included.
Screw the threads for the corner posts (19.)
into the corner posts.
Insert the wooden dowels (12.-13.) into the
blind holes on the corner posts (only half-
drilled holes).
1.
13. 13. 13. 13.
12. 12. 12. 12.
13. 13. 13. 13.
19. 19. 19. 19.
19. 19. 19. 19.
12. 12. 12. 12.
12. 12. 12. 12.
12. 12. 12. 12.
13. 13. 13. 13.
13. 13.

PAGE 5
Place 2 corner posts (D.), 1 end board piece
(A.) and 1 short bars (B.) on the underlay.
e mounting holes must turn upwards on
the end board piece (A.). e end board
piece (A.), the short bars (B.) the lower
panel (J.) must all be in place before assem-
bling.
2.
A.
D. D.
J.
B.
NOTE
Through hole →
Mount the ”half-moon” washer (16) and
the nut for the thread (15.) in the mount-
ing hole on the end board piece (A.).
3.
16.
5.
15.
Mount the upper short bars (B.) to the
corner posts (D.) with the connection nuts
(14.) and the large connection screws (18.)
with the matching washers (8. -7.).
4.
e lower panel (J.) is now mounted with
the corner posts (D.). Use the connection
nuts (14.) and the large connection screws
(18.) with matching washers (8.-7.).
5.
B.D.
J.
14.
18.
8. 7.
NOTE
No hole ↓
Mounting hole →

PAGE 6
Repeat the procedure with the other bed
end and tighten all the connections screws.
6.
A.D. D.
J.
B.
Connect 1 sidepiece (H.) on the rearmost
part of the bedside.
Before tightening the nuts for the threads
in the mounting holes (15.) – (picture 1.),
you must connect the back bar (F.) with
the large connection screws (18.) and the
connection nut (14.)
After this you mount the lower panel (I.)
with the large connection screws (18.) and
the connection nut (14.).
Insert the connection nut (14.) while the
lower panel (I.) is placed on the floor /
underlay (picture 2.).
NOTE.
e connection screws are still NOT
completely tightened.
7.
H.
F.
I.
NOTE
Through hole →
Figure 1.
Figure 2.
16.
5.
15.
14.
I.
NOTE
No hole ↓

PAGE 7
Connect the other sidepiece (H.) in the front
of the loft bed.
Before tightening the nuts for the threads in
the mounting holes (15.) - (picture 1.), you
must connect the back bar (F.) with
the large connection screw (18.) and the
connection nut (14.).
Now decide in which end of the loft bed
you prefer to place the ladder (G.).
e front bar (E.) is now connected to the
corner post (D.) in order to make space for
the ladder.
e loft bed is still not completely
tightened.
Let the sidepiece rest on the thread (19.)
in the end where the ladder is placed –
(picture 4.) when the ladder is placed.
In order to mount the ladder use the me-
dium connection screw (17.), the connection
nut (14.) – (picture 5.), the small connection
screw (6.) and the top nut (4.) – (picture 6.).
8.
H.
E.
Figure 5.
Figure 6.
G.
6.
17.
14.
G.
E.
D.
Figure 4.
H.
D.
E.

PAGE 8
e loft bed can now be tightened com-
pletely.
IMPORTANT: Start with the sidepieces
- tighten all the nuts for the threads (15.).
Hereafter you may now tighten all other
screws.
9.
Place the 2 fixtures for the ladder onto the
ladder and sidepiece with the screws (2.)
10.
9.
2. →
H.
E.
e slatted bed case (C.) is rolled out and
mounted with the screws (3.)
As the sidepieces (H.) are made from solid
wood it can occur that the sidepieces are not
entirely straight. If this occurs you must press
the 2 sidepieces (H.) hard together on the
middle while mounting the slatted bed case
with screws (3.)
11.
C.
3. →

PAGE 9
Now insert the plastic covers (11.) in the
mounting holes over the screws (4. 6. 17. 18.).
e plastic covers (10.) are inserted over the
mounting holes inside the sidepieces (H.) and
the end board pieces (A.). Use a hard object
to insert the plastic covers.
12.
e loft bed is now assembled.
13.

PAGE 10
” IMPORTANT”- SAVE FOR LATER USE: READ CAREFULLY
WARNINGS:
1. The loft bed is not suited for children under the age of 6 years of age due to
danger of falling out of the loft bed.
2. The thickness of the mattress cannot exceed 120 mm. We recommend mattress
thickness between 100 - 120 mm
3. Dimension of the mattress must be minimum 88 x 198 cm.
4. Never leave or place other objects in or close to the loft bed which may cause
danger of suffocation. For example lines, strings etc.
5. Children can be wedged in between the loft bed and the wall. The loft bed must
be placed with a distance to the wall of maximum 75 mm or more than 230 mm.
6. Assembly instruction, descriptions and pictures of all parts of the loft bed and
tools must be included before assembly can take place.
7. All fittings must be tightened, checked regularly and re-tightened.
8. The loft bed must not be used if some parts on the loft bed are damaged or
missing. Only use spare parts approved by Oliver Furniture.
9. The loft bed can be cleaned with a wrung cloth.
10. All safety regulations are described in DS/EN 747-1:2007 (E)